Well, I guess I'm a bad seaman too. I have never closed my seacocks either. I just make sure that my hoses are good and the connections are sound. I could never remember to turn them on when I needed them. I'll take that back. I do have to close to seacock to the sink in the head when the wind is up.
Bill C&C 39 <div>-------- Original message --------</div><div>From: dwight via CnC-List <cnc-list@cnc-list.com> </div><div>Date:05/26/2014 5:18 AM (GMT-05:00) </div><div>To: 'Jim Watts' <paradigmat...@gmail.com>,cnc-list@cnc-list.com </div><div>Subject: Stus-List Seacocks </div><div> </div>My C&C 35 MKII has 7 Groco bronze seacocks, each one placed in a very hard to reach space…since it is well known to be good seamanship to close all seacocks when leaving the boat I wonder why the designers did not make them a little more easily accessible and with longer handles too…I might be more inclined to use them if they were more accessible…however all 7 do move freely open to close, the surveyor confirmed that just last week From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jim Watts via CnC-List Sent: May 26, 2014 2:07 AM To: M Bod; 1 CnC List Subject: Re: Stus-List First sail Either leave the engine seacock open, or hang the ignition key off the seacock handle. Me, I'm useless and we have a Yanmar, so I can start the engine with pretty much anything I have in my pocket including lint. I leave the seacock open. I know this makes me a bad person and I can live with that. Jim Watts Paradigm Shift C&C 35 Mk III Victoria, BC On 25 May 2014 20:13, M Bod via CnC-List <cnc-list@cnc-list.com> wrote: OK. Boat got off the dock today. After a bunch of engine work, new hoses and new fuel tank (all installed by mechanic) everything is supposed to be working smoothly. Well. Getting off the dock was not so smooth. Couldn't sort out why roller furler was jamming for a bit. Finally sorted the issue, started the engine, made sure all looked good (exhaust a little louder than I expected, but not bad). Off we went (had a friend along to assist moving the boat from the marina to a nearby cove where it can stay an extra week). 10 min out I see some smoke riding through the companion way. Throttle down. Full off engine cowling. Coolant everywhere! Must have a leak. We turn around to limp back to the dock. I'm looking at the mess with the coolant boiling over when I realize (OK remember mechanic warned me) the seacock for the engine is CLOSED!!! Opened the seacock. Everything cooled off. We had burned off much of our coolant - so I poured in a 1/2 litre water bottle. Kept the engine at low rpm and made the run to the cove. Little hitch at the end. Went to furl the jib but too much sail and not enough line on the furling drum. Only managed to pack away 2/3 of the sail. Solved that by doing 10 clockwise circles in the bay to wrap the sail around the forestay! Dirty, but it worked. All told we survived. Feel like a royal idiot for forgetting the seacock. Had pretty good water shooting out of the muffler after - but I figure I better pull the impellor and check/replace it anyway. I had checked the exhaust when we started - saw splashes. But later realized I was looking at the air exhaust hitting the water and causing a little splash. Still a little shell shocked from the experience but thinking I'll likely remember the seacock in the future!!!!! Mark _______________________________________________ This List is provided by the C&C Photo Album Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
_______________________________________________ This List is provided by the C&C Photo Album Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com