Airconsole Mini could work for this? https://www.get-console.com/shop/en/airconsole-mini-20/ 112-airconsole-20-mini.html
We use the 8 port variant and they work well enough so far. On 18 May 2018 at 12:03, Aaron Gould <[email protected]> wrote: > I've actually taken out a little 2600 just to act as a 1-port terminal > server for this exact purpose > > (maybe you can even use an old 2500) > > Aaron > > > On May 18, 2018, at 6:00 AM, Aaron Gould <[email protected]> wrote: > > > > I'm not sure if you can use a console port for connecting to another > router's console port , but you can use the auxiliary (aux) port to do > that. I've done it many times > > > > Aaron > > > >> On May 18, 2018, at 1:55 AM, Patrick M. Hausen <[email protected]> wrote: > >> > >> Hi all, > >> > >> last weekend one switch in our VSS pair failed. Redundancy/VSS > >> did work and we kept our connectivity besides a couple of hosts > >> that only have a single uplink and were connected to that particular > >> chassis. > >> > >> When I came to the data centre I found the failed chassis in rommon. > >> A simple "boot" command restored everything to working order. > >> > >> Now to spare me that drive in case that happens again - is it possible > >> to use the console port of a working Catalyst 6500 to act as a terminal > >> server for the other one? We have quite a lot of spare rollover cables > ;-) > >> > >> I found these instructions but I think I'm missing something: > >> https://www.cisco.com/c/en/us/support/docs/dial-access/ > asynchronous-connections/5466-comm-server.html > >> > >> ip host other 2000 1.2.3.4 > >> > >> Core2#telnet 1.2.3.4 2000 > >> Trying 1.2.3.4, 2000 ... > >> % Connection refused by remote host > >> > >> I used the real IP address of looppback0, of course. > >> > >> > >> Side note/question: any idea what could cause a Cat6500 VS-S720-10G > >> to fail, reset (I can understand *that*) and then not boot into IOS and > stay > >> in rommon? > >> > >> Standby BOOT variable = sup-bootdisk:s72033- > adventerprisek9_wan-mz.122-33.SXJ10.bin,1;disk0:s72033- > adventerprisek9_wan-mz.122-33.SXJ10.bin,1; > >> Standby Configuration register is 0x2102 > >> > >> Core2#dir slavesup-bootdisk: > >> ... > >> s72033-adventerprisek9_wan-mz.122-33.SXJ10.bin > >> > >> > >> Thanks! > >> Patrick > >> -- > >> punkt.de GmbH Internet - Dienstleistungen - Beratung > >> Kaiserallee 13a Tel.: 0721 9109-0 Fax: -100 > >> 76133 Karlsruhe [email protected] http://punkt.de > >> AG Mannheim 108285 Gf: Juergen Egeling > >> > >> _______________________________________________ > >> cisco-nsp mailing list [email protected] > >> https://puck.nether.net/mailman/listinfo/cisco-nsp > >> archive at http://puck.nether.net/pipermail/cisco-nsp/ > > > > _______________________________________________ > > cisco-nsp mailing list [email protected] > > https://puck.nether.net/mailman/listinfo/cisco-nsp > > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
