----- Le 8 Avr 15, à 14:21, lijian <blacker1...@163.com> a écrit :
> Hi Stephane, > I dump from a osd deamon You have to apply the mon_osd_down_out_interval value to monitor and not osd. What is the value on the mon ? Stephane. > Thanks > Jian LI > At 2015-04-08 16:05:04, "Stéphane DUGRAVOT" > <stephane.dugra...@univ-lorraine.fr> > wrote: >> ----- Le 7 Avr 15, à 14:57, lijian < blacker1...@163.com > a écrit : >>> Haomai Wang, >>> the mon_osd_down_out_interval is 300, please refer to my settings, and I >>> use the >>> cli 'service ceph stop osd.X' to stop a osd >>> the pg status change to remap,backfill and recovering ... immediately >>> so other something wrong with my settings or operation? >> Hi, >> From what daemon you get the mon_osd_down_out_interval value ? >> Is it from mon or osd ? >> Stephane. >>> Thanks, >>> Jian Ji >>> At 2015-04-07 20:38:29, "Haomai Wang" < haomaiw...@gmail.com > wrote: >>> >Whatever the version you tested, ceph won't recover data when you >>> >manually stop osd immediately. And it will trigger mark down osd out >>> >when it reach "mon_osd_down_out_interval" seconds. >>> >On Tue, Apr 7, 2015 at 8:33 PM, lijian < blacker1...@163.com > wrote: >>> >> Hi, >>> >> The recovering start delay 300s after I stop a osd and the osd status >>> >> change >>> >> from in to out, the test ENV is Ceph 0.80.7 >>> >> But I test in ceph 0.87.1, the recovering start immediately after I stop >>> >> a >>> >> OSD,all the settings is the default value,the following is mon_osd* >>> >> settings >>> >> in my test ENV: >>> >> "mon_osd_laggy_halflife": "3600", >>> >> "mon_osd_laggy_weight": "0.3", >>> >> "mon_osd_adjust_heartbeat_grace": "true", >>> >> "mon_osd_adjust_down_out_interval": "true", >>> >> "mon_osd_auto_mark_in": "false", >>> >> "mon_osd_auto_mark_auto_out_in": "true", >>> >> "mon_osd_auto_mark_new_in": "true", >>> >> "mon_osd_down_out_interval": "300", >>> >> "mon_osd_down_out_subtree_limit": "rack", >>> >> "mon_osd_min_up_ratio": "0.3", >>> >> "mon_osd_min_in_ratio": "0.3", >>> >> "mon_osd_max_op_age": "32", >>> >> "mon_osd_max_split_count": "32", >>> >> "mon_osd_allow_primary_temp": "false", >>> >> "mon_osd_allow_primary_affinity": "false", >>> >> "mon_osd_full_ratio": "0.95", >>> >> "mon_osd_nearfull_ratio": "0.85", >>> >> "mon_osd_report_timeout": "45000", >>> >> "mon_osd_min_down_reporters": "50", >>> >> "mon_osd_min_down_reports": "150", >>> >> "mon_osd_force_trim_to": "0", >>> >> so when the recovering start? why they are different with the two Ceph >>> >> version, or someting wrong with my settings >>> >> Thanks! >>> >> Jian Li >>> >> _______________________________________________ >>> >> ceph-users mailing list >>>>> ceph-users@lists.ceph.com >> >>> >> http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com >>> >-- >>> >Best Regards, >>> >Wheat >>> _______________________________________________ >>> ceph-users mailing list >>> ceph-users@lists.ceph.com >>> http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
_______________________________________________ ceph-users mailing list ceph-users@lists.ceph.com http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
