Hi Yang bin,
Not sure if you followed the right docs. I suspect you didn’t, because you
should use ceph-disk and specified a FS-Type in the command.
I think you might mislead by the quick
start(http://ceph.com/docs/master/start/quick-ceph-deploy/#create-a-cluster),
it use a directory instead of a disk as OSD(“Add two OSDs. For fast setup, this
quick start uses a directory rather than an entire disk per Ceph OSD Daemon.
See ceph-deploy
osd<http://ceph.com/docs/master/rados/deployment/ceph-deploy-osd> for details
on using separate disks/partitions for OSDs and journals.”)
So, just read
http://docs.ceph.com/docs/master/rados/deployment/ceph-deploy-osd/ or
http://ceph.com/docs/master/install/manual-deployment/#adding-osds may help
your case.
Xiaoxi
From: ceph-users [mailto:ceph-users-boun...@lists.ceph.com] On Behalf Of
yang.bi...@zte.com.cn
Sent: Monday, December 22, 2014 3:58 PM
To: Karan Singh
Cc: ceph-users
Subject: [ceph-users] 答复: Re: can not add osd
Hi
I have deploied ceph osd according official Ceph docs,and the same error came
out again.
发件人: Karan Singh <karan.si...@csc.fi<mailto:karan.si...@csc.fi>>
收件人: yang.bi...@zte.com.cn<mailto:yang.bi...@zte.com.cn>,
抄送: ceph-users
<ceph-users@lists.ceph.com<mailto:ceph-users@lists.ceph.com>>
日期: 2014/12/16 22:51
主题: Re: [ceph-users] can not add osd
________________________________
Hi
You logs does not provides much information , if you are following any other
documentation for Ceph , i would recommend you to follow official Ceph docs.
http://ceph.com/docs/master/start/quick-start-preflight/
****************************************************************
Karan Singh
Systems Specialist , Storage Platforms
CSC - IT Center for Science,
Keilaranta 14, P. O. Box 405, FIN-02101 Espoo, Finland
mobile: +358 503 812758
tel. +358 9 4572001
fax +358 9 4572302
http://www.csc.fi/
****************************************************************
On 16 Dec 2014, at 09:55, yang.bi...@zte.com.cn<mailto:yang.bi...@zte.com.cn>
wrote:
hi
When i execute "ceph-deploy osd prepare node3:/dev/sdb",always come out err
like this :
[node3][WARNIN] INFO:ceph-disk:Running command: /bin/umount --
/var/lib/ceph/tmp/mnt.u2KXW3
[node3][WARNIN] umount: /var/lib/ceph/tmp/mnt.u2KXW3: target is busy.
Then i execute "/bin/umount -- /var/lib/ceph/tmp/mnt.u2KXW3",result is ok.
--------------------------------------------------------
ZTE Information Security Notice: The information contained in this mail (and
any attachment transmitted herewith) is privileged and confidential and is
intended for the exclusive use of the addressee(s). If you are not an intended
recipient, any disclosure, reproduction, distribution or other dissemination or
use of the information contained is strictly prohibited. If you have received
this mail in error, please delete it and notify us immediately.
_______________________________________________
ceph-users mailing list
ceph-users@lists.ceph.com<mailto:ceph-users@lists.ceph.com>
http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
--------------------------------------------------------
ZTE Information Security Notice: The information contained in this mail (and
any attachment transmitted herewith) is privileged and confidential and is
intended for the exclusive use of the addressee(s). If you are not an intended
recipient, any disclosure, reproduction, distribution or other dissemination or
use of the information contained is strictly prohibited. If you have received
this mail in error, please delete it and notify us immediately.
_______________________________________________
ceph-users mailing list
ceph-users@lists.ceph.com
http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
