Hi Mark, Ooo! Awesome! It turns out my setup is missing a lot of things so rebuilding drivers doesn't seem to work. I am looking at redoing the install in a SIMH pdp11 to see if I can get a more complete installation. But this looks like it should solve the immediate problem. I will definitely try this later today when I get back home from work.
Thank you! - Peter On Tue, Dec 31, 2024 at 10:14 AM Mark Matlock <m...@matlockfamily.com> wrote: > Peter, > I just set up a pregenned RL02 based RSX11M+ and took a look at the DD > driver. It is a vectored driver and needs to have the /VEC switch to tell > it not to use the default RSX11M.STB but instead use RSXVEC.STB > > I was able to load the DDDRV with: > > >LOA DD:/VEC/PAR=GEN/HIGH > > The /PAR=GEN overrides trying to put the driver in DRVPAR that won’t have > room for it unless you reVMR > The /HIGH puts the driver at highest available memory in GEN to avoid > fragmenting the memory in GEN > > Best, > Mark > > On Dec 30, 2024, at 4:21 PM, Peter Ekstrom <epekst...@gmail.com> wrote: > > Hi Mark, > > Thank you so much for this information! Seeing this, I was on the right > track but was missing a few items. > I typed this into a file on the PDP and ran it, but now it turns out I > don't have the RSX11M.OLB file, so I guess I am just going to have to work > on getting the sysgen stuff onto my disk. > > Again, thank you very much for the info! > > -Peter > > > On Mon, Dec 30, 2024 at 3:20 PM Mark Matlock <m...@matlockfamily.com> > wrote: > >> Peter, >> The command file below is from a SYSGEN driver build of DDDRV from my >> system but I think it should work for yours. Note that OU: is defined by >> the SYSGEN process and should be set as a logical to your system disk >> (DL0:) or perhaps more simply just edited to be SY: Also, note that it uses >> RSXVEC.STB which should work on the pregenned RL02 RSX11M+. >> >> [200,200]DDDRVBLD.CMD >> ; >> ; DDDRVBLD.CMD -- RSX-11M-PLUS loadable DD: driver build command file >> ; >> ; Created on 01-NOV-2024 at 14:00:05 >> ; >> OU:[1,54]DDDRV/-MM/-HD,SY:[1,34]DDDRV/SH/-SP,OU:[1,54]DDDRV= >> SY:[1,24]RSX11M/LB:DDDRV:DDTAB >> LB:[3,54]RSXVEC.STB/SS >> LB:[1,1]EXELIB/LB >> / >> STACK=0 >> PAR=DRVPAR:120000:20000 >> / >> >> If for some reason you need to assemble the DDDRV driver below is the >> SYSGEN produced assembly command files. >> >> >> [200,200]DDDRVASM.CMD >> ; >> ; DDDRVASM.CMD -- RSX-11M-PLUS loadable DD: driver assembly command file >> ; >> ; Created on 01-NOV-2024 at 12:56:02 >> ; >> >> OU:[11,24]DDDRV,LS:[11,34]DDDRV/-SP=IN:[1,1]EXEMC/ML,[11,10]RSXMC/PA:1,DDDRV >> >> OU:[11,24]DDTAB,LS:[11,34]DDTAB/-SP=IN:[1,1]EXEMC/ML,[11,10]RSXMC/PA:1,DDTAB >> >> Good Luck, >> Mark >> >> >> 1. I need some RSX11M+ TKB help (Peter Ekstrom) >> >> *From: *Peter Ekstrom <epekst...@gmail.com> >> *Subject: **[cctalk] I need some RSX11M+ TKB help* >> *Date: *December 29, 2024 at 6:21:46 PM CST >> *To: *"General Discussion: On-Topic and Off-Topic Posts" < >> cctalk@classiccmp.org> >> *Reply-To: *"General Discussion: On-Topic and Off-Topic Posts" < >> cctalk@classiccmp.org> >> >> I have RSX11M+ 4.6 BL87 installed and running on my real PDP 11/23+ and >> have gotten DECnet to work as well. But recently a need to access a TU58 >> tape has come up, and turns out the DD driver on disk isn't built against >> the correct RSX11M.STB file. So I need to, I guess, recreate the DDDRV.TSK >> file. I have tried some very simplistic TKB commands but keep getting an >> error saying a required file is missing. >> >> I don't have the sysgen stuff on this disk... What I have comes from the >> pregenned RL02 image. >> >> Does anyone know how the TKB command line should look for this? I know, I >> am looking for the easy way out. I have skimmed through some manuals but >> nothing has stood out to me (I'm sure I missed it). >> >> Any help would be greatly appreciated. >> >> - Peter >> >> >
