Thanks Rod!

I discovered an immediate problem I hadn't caught before.. two of the trimmer 
resistors had actually been broken right off two of their legs.. so that may 
account for strange/missing voltages.   They are a CONRAC part 928237.  The CRT 
is CONRAC too, but I still don't think this is a CONRAC terminal.  Anyway, I 
only found one source for the exact resistor, an aerospace company, and they 
want $80 per unit (I think they just want me to go away).

So far in testing I haven't found any shorts.  My main worry is the PSU sending 
incorrect voltages to wrong place.  In addition to the broken resistors I also 
discovered some broken solder joints on the PSU PCB.. those at least are 
repaired.  I'm trying to figure out the resistance the two resistors were set 
to so I can put a replacement in with same, hopefully that gets me close to 
what should be there.

Brad

-----Original Message-----
From: Rod Smallwood via cctalk <cctalk@classiccmp.org> 
Sent: Wednesday, July 5, 2023 8:48 AM
To: Douglas Taylor via cctalk <cctalk@classiccmp.org>
Cc: Rod Smallwood <rodsmallwoo...@btinternet.com>
Subject: [cctalk] Re: 1974 No Name Terminal

I worked on VDU's as an engineer in the UK before joining DEC to sell volume 
VT100's in 1975

There's a mention of block on one of the cards so a block mode terminal.

That means enter data and press a key to send the lot.

The card cage could mean its emulating something.

I'd test as many capacitors as possible. PSU first and replace as required.

Run PSU and check voltages.

  Check each board for power rail to ground shorts.

  If ok give each board +5v on its own and see if the TTL is alive.

If theres a clock gen start there (look for a crystal can)

  Loads of fans might indicate an industrial environment

   At this age some TTL will have failed plus capacitors.

  Rod Smallwood


On 05/07/2023 16:28, Douglas Taylor via cctalk wrote:
> At first glance it reminded me of the Hazeltine 1000, I owned one in 
> the early 1980's.  Brutally simple terminals, I remember getting a ROM 
> from Jameco which allowed the terminal to display lowercase letters.
> Pure luxury.
> Doug
>
> On 7/4/2023 6:57 PM, Brad H via cctalk wrote:
>> Hi there - not sure how much overlap there is with vcfed's forum, but 
>> thought I would reach out here in case.  I have a terminal from 1974 
>> (based on date codes I've found on the motherboard).  I'm unable to 
>> determine manufacturer and that would be handy for diagnostic 
>> purposes. The terminal casing is made out of foam, and although there 
>> are some serial numbers stamped around, nothing really lines up.  The 
>> fans inside have zero dust or dirt, so I'm thinking this may not have 
>> seen much use, or may be a prototype or pilot for something.  It does 
>> have RS232 capability. Interestingly the screen is set down below the 
>> keyboard so that only half of it is visible.
>>
>>
>> My main issue right now is the PSU - I am trying to determine if I'm 
>> safe to attempt powering up the board (the PSU so far seems to be ok, 
>> although some voltages on a couple of pins are mysterious).
>>
>>
>> Anyway, on the extremely off chance anyone has ever seen one of these 
>> or something like it.. any tips would be appreciated. If I can find a 
>> manual I'll feel a lot safer about turning it on.
>>
>>
>> Some pics here:
>> https://drive.google.com/drive/folders/1-2uEFbi3OKBYr06y6yHnygDiLMtw2
>> Qkj?usp
>>
>> =sharing
>>
>>
>> Brad
>>
>> b...@techtimetraveller.com
>>
>>
>

Reply via email to