Thank you EVERYONE. Yes I confirmed that the red disc is a heater and the 
little device on the side is a temp sensor. All is good.

I will send a new email out with some new questions but wanted to tie off this 
discussion with thanks to all

Eugene


-----Original Message-----
From: cctalk <cctalk-boun...@classiccmp.org> On Behalf Of dwight via cctalk
Sent: Friday, June 26, 2020 9:26 AM
To: General Discussion: On-Topic and Off-Topic Posts <cctalk@classiccmp.org>
Subject: Re: IDE Hard Drive Question

I'd measure the temperature sensor. It is most likely a typical thermistor but 
may be an RTD. Most RTD's are 100 ohm but there are some platinum on ceramic 
that are 1K ohms. Check it both directions with an ohm meter. It might be a 
solid state semiconductor type device. If a resistive device, it can likely be 
replaced by a resistor. If it is 10K thermistor or whatever just replace it 
with a fixed resistor.
Put it in the fridge for a few minutes to see if it is a negative or positive 
temperature coefficient. Once you know that it should be easy to use a value of 
resistor that would tell it that is was at a happy 20c.
You can likely leave the heater leads open.
The temperature sensor is the small black thing. I doubt it is a thermal switch 
but it might be. It is most likely to be around specific resistances of 10 
ohms, 100, 1K or 10K.
Dwight

________________________________
From: cctalk <cctalk-boun...@classiccmp.org> on behalf of jim stephens via 
cctalk <cctalk@classiccmp.org>
Sent: Thursday, June 25, 2020 11:59 PM
To: cct...@classiccmp.org <cct...@classiccmp.org>
Subject: Re: IDE Hard Drive Question



On 6/25/2020 11:20 PM, Chuck Guzis via cctech wrote:
> On 6/25/20 4:12 PM, Jon Elson via cctech wrote:
>> On 06/25/2020 05:29 PM, W2HX via cctech wrote:
>>> Does ANYONE have any idea what these 4 wires are connected to and why?
>>> And anyone give any odds about whether these 4 wires will prevent 
>>> this IDE-SD converter from working?
>>>
>>>
>> Temperature sensor and heater.  Undoubtedly for start-up in extreme 
>> cold conditions.
> Certainly looks like that to me also.  Sits right atop the spindle motor.
>
> --Chuck
>
The drive spec I found for the Conner cfs540a (this drive) shows an operating 
range of 5c to 55c.

The top of the range is useful for mil operations, but the 5c spec would be bad 
if you ran the drive.

Full military just a casual google says is -55c, and extended industrial is 
-40c on the bottom.  We did -40 specs for some of our projects, but nothing 
mechanical. The are at -40c to 60c for nonoperating, so would be close to the 
low range if they could heat the spindle, and let the drive heat itself up.

One issue might be that the sensor will heat up this dongle and allow the thing 
to run, but there may be a provision to spin the drive before it is expected to 
run.  A heat up or warmup feature might be performed besides what Jon suggested 
with the heater / sensor.

I suspect this thing has to heat up and be at temp before something in the bios 
or otherwise allows the drive to run.

The OP might look around and see if there are any of the heater strips around 
as well, to allow heating in the drive box as needed.

I may have one of these systems with some extra drives, and the good news is 
they guy I bought them from if mine are the same or of similar spec, is that he 
was putting drives in the boxes from random drive buys and they were easy to 
run.  He didn't recall the spindle dongle on his drive pods though.

I'm waiting to hear for sure if the fellow I bought mine from remembers the 
manufacturer.  The system and an auxiliary box of similar size with more pods 
came in a deal I couldn't pass up.  My box has got a 486 motherboard and 
functional 10baseT card running in it.  I plan to use one of the pods to do one 
of these as solid state to save runtime on the physical disks.


spec I used at:
ftp://ftp.seagate.com/techsuppt/seagate_utils/allconnr.pdf


Reply via email to