Agree Show running is my best trouble shooting command.
So I would never go down that road of practicing without... I´am too stupid to remember all the Cisco IOS commands I need. Med venlig hilsen | Best regards Thomas Raabo Senior Network Engineer CCIE #33466 _____________________________________________ [email protected] | Direkte: +45 69 10 60 18 | Tlf.: +45 70 23 55 66 -----Oprindelig meddelelse----- Fra: [email protected] [mailto:[email protected]] På vegne af Arista Wirawan Sendt: 30. maj 2012 17:49 Til: Rishika Goyal; George Leslie Cc: [email protected] Emne: Re: [OSL | CCIE_RS] Troubleshooting section on R&S exam I found show run with "section" or "include" (on switch) command is quite useful on ccie ts to scanning the possible root cause together with other command depend on the issue such as show access-list, show ip ospf int b, show route-map, show ip route, show ip bgp, show spanning-tree, etc. So why not using it. Aris CCIE #35534 Sent from my HTC ----- Reply message ----- From: "Rishika Goyal" <[email protected]> To: "George Leslie" <[email protected]> Cc: "IPExpert Study List" <[email protected]> Subject: [OSL | CCIE_RS] Troubleshooting section on R&S exam Date: Wed, May 30, 2012 6:57 PM Hi George, There is nothing called "barred" in CCIE lab, all you got to know is the rules of the game. show runn would eat your time unnecessarily and you already have limited time at hand when it comes to troubleshooting. You cant just think of having a rough guess by doing sh runn , if you know the real problem just focus on the specifics rather than looking at full config. You can run debug all as well at your free will in lab and crash your routers. But all you need to make sure is that you grab those 8 tickets in less than 2 hours. Its all about time management and having razor sharp eyes to know where the fault is - which comes with knowing the technology. All the best with your studies. Regards, Rishika Goel CCIE# 33041 On Wed, May 30, 2012 at 3:00 PM, George Leslie <[email protected] > wrote: > > > > > Hi all,Very simple question! On the troubleshooting section of the > real exam, are you barred from using "show runn" or "show start"? > Reason I ask is that lots of verification you see in the lab books and > the videos tend to shy away from using show runn etc. I just wondered > if this was to try and build good habits, or out of necessity due to > show runn being not allowed? Regards, George. > _______________________________________________ > For more information regarding industry leading CCIE Lab training, > please visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
