Are both interface using the same network type? What verification have you done?
Michael Davis CCIE #26050, CISSP #376023 , ECC C|EH MCSE Webquor Services Pty Limited Suite 504, Level 5 105 Pitt Street Sydney NSW 2000 [email protected] <mailto:[email protected]> Tel: 1300 653 115 Fax: +61 (2) 8905 9224 ITIL® Accredited <http://www.itil-officialsite.com/> ITIL® <http://www.itil-officialsite.com/> is a Registered Trade Mark of the Office of Government Commerce, in the United Kingdom and other countries. P Please consider the environment before printing this email "This communication is intended for the addressed recipient only. It may contain information that is privileged, confidential and/or exempt from disclosure. If you are not the intended recipient, you are notified that any use, disclosure, dissemination or any action taken or admitted to be taken or reliance on it is strictly prohibited. If you have received this e-mail in error, please reply to the sender immediately and delete the document. Except as required by law, Webquor Services Pty. Limited does not represent, warrant and/or guarantee that the integrity of this communication has been maintained. We also do not guarantee that the communication is free of errors, virus, interception or interference, but do assume that the utmost effort and technology has been utilised to ensure that the information is free from such effects². On 6/03/12 7:57 PM, "khaled al-ajeman" <[email protected]> wrote: >Hi fellas, > >I have the neighbor relation ship formed between R9 and R98, however, the >routes are not travelling from R9 AND R98 and vise verse, can anyone tell >please why? > >Here is my configuration below: > >R9 > >R9(config)#do sh run | s os >hostname R9 > ip ospf network broadcast >router ospf 1 > log-adjacency-changes > passive-interface default > no passive-interface FastEthernet0/0 > no passive-interface Serial0/1 > network 150.50.69.0 0.0.0.255 area 69 > network 150.50.98.0 0.0.0.127 area 96 ------------------------------ >> I am looking at area 96 > >R98(config)#do sr | s os >hostname vlan98 >router ospf 1 > router-id 96.96.96.96 > log-adjacency-changes > passive-interface default > no passive-interface FastEthernet0/0 > network 10.10.0.0 0.0.0.0 area 96 > network 10.10.1.0 0.0.0.0 area 96 > network 10.10.2.0 0.0.0.0 area 96 > network 10.10.3.0 0.0.0.0 area 96 > network 10.10.4.0 0.0.0.0 area 96 > network 10.10.5.0 0.0.0.0 area 96 > network 10.10.6.0 0.0.0.0 area 96 > network 150.50.98.0 0.0.0.127 area >96 ------------------------------ area 96 > >the neighbor relationship forming bet R9 AND R98 > > >R9 > >R9(config)#do sh ip os nei >Neighbor ID Pri State Dead Time Address >Interface >200.0.0.6 1 FULL/DR 00:00:32 150.50.69.6 >Serial0/1 >96.96.96.96 1 FULL/DR 00:00:32 150.50.98.10 >FastEthernet0/0 --------------- successfully forming >relationship with R98 >R98 > >R98(config)#DO SH IP OS NEI >Neighbor ID Pri State Dead Time Address >Interface --------------------- successfully >forming >relationship with R9 >200.0.0.9 1 FULL/BDR 00:00:34 150.50.98.9 >FastEthernet0/0 > > >thanks so much fellas > >khaled >_______________________________________________ >For more information regarding industry leading CCIE Lab training, please >visit www.ipexpert.com > >Are you a CCNP or CCIE and looking for a job? Check out >www.PlatinumPlacement.com > >http://onlinestudylist.com/mailman/listinfo/ccie_rs _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
