Per Les email set your config register to 2102. Reboot and configure,,,
Note you may want to write erase nvram to ensure that you boot up fully clean JoE On Mar 2, 2012 5:12 AM, "Mohammad Zahid Stanikzai" < [email protected]> wrote: > Joe, > > Not it isn't , the IOS version is c2500-is-l.122-15.T17.bin > > Tweaking with the protocol number sometimes work. > > Regards,. > > Zahid > > -----Original Message----- > From: Joe Danrich [mailto:[email protected]] > Sent: Friday, March 02, 2012 8:37 AM > To: Mohammad Zahid Stanikzai > Cc: 'Edgar Mauricio Diaz Orellana'; 'Jacob Zartmann'; 'Hilton Woods'; > [email protected] > Subject: Re: [OSL | CCIE_RS] Access=Server > > Zaid > > Is the 2511 retaining any of it's configuration? > > Also what IOS version are you running.. > > Cheers > > Joe > > > On 03/01/2012 12:42 PM, Mohammad Zahid Stanikzai wrote: > > Yes, > > > > > > > > I did the clear line, but when I turn off and restart it second day it > > will not work some of them will work and others are giving error. > > > > > > > > I use 2511 RJ > > > > > > > > > > > > From: Edgar Mauricio Diaz Orellana [mailto:[email protected]] > > Sent: Friday, March 02, 2012 1:05 AM > > To: Jacob Zartmann > > Cc: Mohammad Zahid Stanikzai;<[email protected]> > > Subject: Re: [OSL | CCIE_RS] Access=Server > > > > > > > > i read wrong.. sorry for my mistake... just you need to play with show > > lines and clear line<number> when it's stuck.. > > > > > > > > > > > > On Thu, Mar 1, 2012 at 5:34 PM, Edgar Mauricio Diaz Orellana > > <[email protected]> wrote: > > > > check my friend the config-register :-) > > > > > > > > On Thu, Mar 1, 2012 at 5:04 PM, Jacob Zartmann<[email protected]> > wrote: > > > > If you've got a 2509 or 2511 for access server, you'll a lot of times > > need to clear the lines a couple of times before you're able to connect. > > > > /JZ > > > > Sent from my iPhone > > > > > > On 01/03/2012, at 18.30, Mohammad Zahid Stanikzai > > <[email protected]> wrote: > > > >> Dears, > >> > >> > >> > >> I configured my own lab with the devices listed on ine website and > >> other sources and I had purchased Access-Server RJ-45 Series, > >> > >> > >> > >> I configured and it works well but I shut the lab off and next day if > >> I > > want > >> to access the routers or switches some of them are access able and > >> some > > says > >> that connection refused by host, it really take my whole time to do > >> the whole process again and again spending 2 to 3 hours and then It > >> will work, can any one till me why is this doing like this ? > >> > >> > >> > >> Regards, > >> > >> > >> > >> Zahid > >> > >> > >> > >> _______________________________________________ > >> For more information regarding industry leading CCIE Lab training, > >> please > > visit www.ipexpert.com > >> Are you a CCNP or CCIE and looking for a job? Check out > > www.PlatinumPlacement.com > >> http://onlinestudylist.com/mailman/listinfo/ccie_rs > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, > > please visit www.ipexpert.com > > > > Are you a CCNP or CCIE and looking for a job? Check out > > www.PlatinumPlacement.com > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > > > > > > > > > > > > > > > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
