Glad to offer possible assistance. Good luck on your project. Do you know how I can post a question to the entire BVARC community?
I have an interesting question regarding EMP I am sure will get lots of responses. > On May 1, 2017, at 7:52 PM, Gary Sitton via BVARC <[email protected]> wrote: > > Fred: > > I believe I found a local solution, but thanks. I'll > keep you in mind if this doesn't work out. > > 73s, > Gary Sitton, K5AMH > [email protected] <mailto:[email protected]> > > On 5/1/2017 19:12, Frederic R Wenzel via BVARC wrote: >> We have machining equipment that can machine your holes for you. I assume >> from note below, that you just need to enlarge the 0.500” holes to 0.750” >> holes (though holes). This is easy job to accomplish. >> >> We are in Katy at 27027 Westheimer Parkway, suite 700, Katy, TX 77494. Just >> south of Katy Mills Mall. Give us a call at 281-382-8987, or my cell at >> 713-206-7802 tomorrow to discuss. >> >>> On May 1, 2017, at 6:57 PM, Rick Hiller via BVARC <[email protected] >>> <mailto:[email protected]>> wrote: >>> >>> Ok I'm an idiot. You want to enlarge the holes. Sorry. Misunderstood. >>> Never mind my offer. Again sorry! >>> >>> Sent from my i-Thingamajig >>> >>> On May 1, 2017, at 6:16 PM, rodney martinez via BVARC <[email protected] >>> <mailto:[email protected]>> wrote: >>> >>>> My bad....center punching is not necessary with a HALF INCH existing hole. >>>> Didnt read the minor details in the request. Anyway, call me and we can >>>> do it here. I have a 24 volt monster drill here. You hold one side, and >>>> I will hold the other. >>>> >>>> Rod >>>> >>>> >>>> On Monday, May 1, 2017 6:08 PM, rodney martinez via BVARC <[email protected] >>>> <mailto:[email protected]>> wrote: >>>> >>>> >>>> I have a heavy duty portable drill, and center punching. We can do it >>>> here in my garage in Meyerland. >>>> >>>> Helping out a fellow BVARC member tomorrow morning at 1100, but home after >>>> 1300 hours tomorrow afternoon. >>>> >>>> Rod Martinez >>>> KC5MZK >>>> 832-423-5640 >>>> >>>> >>>> On Monday, May 1, 2017 5:54 PM, Gary Sitton via BVARC <[email protected] >>>> <mailto:[email protected]>> wrote: >>>> >>>> >>>> Anyone know of anyone with the skills and tools to bore out four 1/2" >>>> holes >>>> in an aluminum plate to 3/4". I'm very willing to pay. I considered a >>>> step-bit or a straight drill but either is tricky, etc. This is for a base >>>> plate on an antenna mast. The material is 6061-T6. >>>> >>>> Gary, K5AMH >>>> >>>> Sent with AquaMail for Android >>>> http://www.aqua-mail.com <http://www.aqua-mail.com/> >>>> >>>> >>>> >>>> _______________________________________________ >>>> BVARC mailing list >>>> [email protected] <mailto:[email protected]> >>>> http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org >>>> <http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org> >>>> Message delivered to [email protected] <mailto:[email protected]> >>>> >>>> >>>> _______________________________________________ >>>> BVARC mailing list >>>> [email protected] <mailto:[email protected]> >>>> http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org >>>> <http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org> >>>> Message delivered to [email protected] <mailto:[email protected]> >>>> >>>> >>>> _______________________________________________ >>>> BVARC mailing list >>>> [email protected] <mailto:[email protected]> >>>> http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org >>>> <http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org> >>>> Message delivered to [email protected] <mailto:[email protected]> >>> _______________________________________________ >>> BVARC mailing list >>> [email protected] <mailto:[email protected]> >>> http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org >>> <http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org> >>> Message delivered to [email protected] <mailto:[email protected]> >> >> >> _______________________________________________ >> BVARC mailing list >> [email protected] <mailto:[email protected]> >> http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org >> <http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org> >> Message delivered to [email protected] <mailto:[email protected]> > > > _______________________________________________ > BVARC mailing list > [email protected] > http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org > Message delivered to [email protected]
_______________________________________________ BVARC mailing list [email protected] http://mail.bvarc.org/mailman/listinfo/bvarc_bvarc.org Message delivered to [email protected]
