On my OpenBSD 7.3 arm64 system i executed sysupgrade and the automatic reboot comes to this. If you need more info, let me know, happy to provide it. Cheers! U-Boot SPL 2021.10 (Mar 25 2023 - 15:00:03 -0600) DRAM: 2048 MiB Trying to boot from MMC2 NOTICE: BL31: v2.7(debug):2.7.0 NOTICE: BL31: Built : 14:34:12, Mar 25 2023 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x209a720, model: Pinebook INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller INFO: PMIC: Probing AXP803 on RSB INFO: PMIC: dcdc1 voltage: 3.300V INFO: PMIC: dcdc5 voltage: 1.200V INFO: PMIC: dcdc6 voltage: 1.100V INFO: PMIC: dldo1 voltage: 3.300V INFO: PMIC: dldo2 voltage: 2.500V INFO: PMIC: dldo4 voltage: 3.300V INFO: PMIC: fldo1 voltage: 1.200V INFO: PMIC: Enabling DC SW INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 843419 was applied INFO: BL31: cortex_a53: CPU workaround for 855873 was applied INFO: BL31: cortex_a53: CPU workaround for 1530924 was applied INFO: PSCI: Suspend is unavailable INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9
U-Boot 2021.10 (Mar 25 2023 - 15:00:03 -0600) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Pinebook DRAM: 2 GiB MMC: mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... Unable to read "uboot.env" from mmc1:1... In: serial Out: vidconsole Err: vidconsole Net: No ethernet found. starting USB... Bus usb@1c1a000: USB EHCI 1.00 Bus usb@1c1a400: USB OHCI 1.0 Bus usb@1c1b000: USB EHCI 1.00 Bus usb@1c1b400: USB OHCI 1.0 scanning bus usb@1c1a000 for devices... 2 USB Device(s) found scanning bus usb@1c1a400 for devices... 1 USB Device(s) found scanning bus usb@1c1b000 for devices... 4 USB Device(s) found scanning bus usb@1c1b400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:1... libfdt fdt_check_header(): FDT_ERR_BADMAGIC MMC: no card present Scanning disk m...@1c0f000.blk... Disk m...@1c0f000.blk not ready Card did not respond to voltage select! : -110 Scanning disk m...@1c10000.blk... Disk m...@1c10000.blk not ready Scanning disk m...@1c11000.blk... Found 3 disks No EFI system partition BootOrder not defined EFI boot manager: Cannot load any image Found EFI removable media binary efi/boot/bootaa64.efi 219050 bytes read in 6 ms (34.8 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC Booting /efi\boot\bootaa64.efi disks: sd0* >> OpenBSD/arm64 BOOTAA64 1.18 boot> NOTE: random seed is being reused. booting sd0a:/bsd: 10659652+2524680+295936+849936 [789702+91+1219896+731148]=0x13b5180 [ using 2741616 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2023 OpenBSD. All rights reserved. https://www.OpenBSD.org OpenBSD 7.4 (GENERIC.MP) #2273: Tue Oct 10 09:45:06 MDT 2023 dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP real mem = 2027720704 (1933MB) avail mem = 1928769536 (1839MB) random: boothowto does not indicate good seed mainbus0 at root: Pinebook psci0 at mainbus0: PSCI 1.1, SMCCC 1.2 efi0 at mainbus0: UEFI 2.8 efi0: Das U-Boot rev 0x20211000 smbios0 at efi0: SMBIOS 3.0 smbios0: vendor U-Boot version "2021.10" date 10/01/2021 smbios0: Unknown Unknown Product cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu0: 512KB 64b/line 16-way L2 cache cpu0: CRC32,SHA2,SHA1,AES+PMULL,ASID16 cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4 cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu1: 512KB 64b/line 16-way L2 cache cpu1: CRC32,SHA2,SHA1,AES+PMULL,ASID16 cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4 cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu2: 512KB 64b/line 16-way L2 cache cpu2: CRC32,SHA2,SHA1,AES+PMULL,ASID16 cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4 cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu3: 512KB 64b/line 16-way L2 cache cpu3: CRC32,SHA2,SHA1,AES+PMULL,ASID16 apm0 at mainbus0 "display-engine" at mainbus0 not configured "osc24M_clk" at mainbus0 not configured "osc32k_clk" at mainbus0 not configured "pmu" at mainbus0 not configured simpleaudio0 at mainbus0 agtimer0 at mainbus0: 24000 kHz simplebus0 at mainbus0: "soc" sxisyscon0 at simplebus0 sxisid0 at simplebus0 sxiccmu0 at simplebus0 sxipio0 at simplebus0: 103 pins ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1, 2: "interrupt-controller" sxirtc0 at simplebus0 sxiccmu1 at simplebus0 sxitwi0 at simplebus0 iic0 at sxitwi0 "analogix,anx6345" at iic0 addr 0x38 not configured sxipio1 at simplebus0: 13 pins sxirsb0 at simplebus0 axppmic0 at sxirsb0 addr 0x3a3: AXP803 "bus" at simplebus0 not configured "dma-controller" at simplebus0 not configured "lcd-controller" at simplebus0 not configured "lcd-controller" at simplebus0 not configured "video-codec" at simplebus0 not configured sximmc0 at simplebus0 sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma sximmc1 at simplebus0 sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma sximmc2 at simplebus0 sdmmc2 at sximmc2: 8-bit, sd high-speed, mmc high-speed, dma "crypto" at simplebus0 not configured "mailbox" at simplebus0 not configured "phy" at simplebus0 not configured ehci0 at simplebus0 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci0 at simplebus0: version 1.0 ehci1 at simplebus0 usb1 at ehci1: USB revision 2.0 uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci1 at simplebus0: version 1.0 "dai" at simplebus0 not configured "codec" at simplebus0 not configured sxitemp0 at simplebus0 com0 at simplebus0: dw16550 com0: console "gpu" at simplebus0 not configured sxipwm0 at simplebus0 "dram-controller" at simplebus0 not configured "deinterlace" at simplebus0 not configured "hdmi-phy" at simplebus0 not configured sxirintc0 at simplebus0 "codec-analog" at simplebus0 not configured sxidog0 at simplebus0 gpio0 at sxipio0: 32 pins gpio1 at sxipio0: 32 pins gpio2 at sxipio0: 32 pins gpio3 at sxipio0: 32 pins gpio4 at sxipio0: 32 pins gpio5 at sxipio0: 32 pins gpio6 at sxipio0: 32 pins gpio7 at sxipio0: 32 pins gpio8 at sxipio1: 32 pins usb2 at ohci0: USB revision 1.0 uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 usb3 at ohci1: USB revision 1.0 uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 "opp_table0" at mainbus0 not configured pwmbl0 at mainbus0 gpiokeys0 at mainbus0: "Lid Switch" "panel-edp" at mainbus0 not configured "vbklt" at mainbus0 not configured "vcc5v0" at mainbus0 not configured "wifi_pwrseq" at mainbus0 not configured simpleamp0 at mainbus0 "binman" at mainbus0 not configured simplefb0 at mainbus0: 1920x1080, 32bpp wsdisplay0 at simplefb0 mux 1 wsdisplay0: screen 0-5 added (std, vt100 emulation) manufacturer 0x024c, product 0xb703 at sdmmc1 function 1 not configured scsibus0 at sdmmc2: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <Samsung, AJTD4R, 0000> removable sd0: 14910MB, 512 bytes/sector, 30535680 sectors run0 at uhub0 port 1 configuration 1 interface 0 "Ralink 802.11 n WLAN" rev 2.00/1.01 addr 2 run0: MAC/BBP RT5390 (rev 0x0502), RF unknown (MIMO 1T1R), address 00:25:22:44:43:e0 uhub4 at uhub1 port 1 configuration 1 interface 0 "Genesys Logic USB2.0 Hub" rev 2.00/88.32 addr 2 uhidev0 at uhub4 port 1 configuration 1 interface 0 "HAILUCK CO.,LTD USB KEYBOARD" rev 1.10/1.00 addr 3 uhidev0: iclass 3/1 ukbd0 at uhidev0: 8 variable keys, 6 key codes wskbd0 at ukbd0 mux 1 wskbd0: connecting to wsdisplay0 uhidev1 at uhub4 port 1 configuration 1 interface 1 "HAILUCK CO.,LTD USB KEYBOARD" rev 1.10/1.00 addr 3 uhidev1: iclass 3/0, 9 report ids ums0 at uhidev1 reportid 1: 5 buttons, Z and W dir wsmouse0 at ums0 mux 0 uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0 ucc0 at uhidev1 reportid 3: 24 usages, 15 keys, enum wskbd1 at ucc0 mux 1 wskbd1: connecting to wsdisplay0 uhid1 at uhidev1 reportid 5: input=0, output=0, feature=5 uhid2 at uhidev1 reportid 6: input=0, output=0, feature=255 uhid3 at uhidev1 reportid 9: input=1, output=0, feature=0 uvideo0 at uhub4 port 3 configuration 1 interface 0 "Generic USB2.0 PC CAMERA" rev 2.00/1.00 addr 4 video0 at uvideo0 vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets root on sd0a (6bec12928f691e87.a) swap on sd0b dump on sd0b WARNING: /mnt was not properly unmounted panipca:ni atct:e m p t t o uavcmc_efsasu lt f a il e d : ff f f f f 7 f ucsaecr9 2 ad0dcdr ees ssr 806x020 0 f0ro0m4 EfarL1 fStopped at panic+0x164: cmp w21, #0x0 TID PID UID PRFLAGS PFLAGS CPU COMMAND 333802 82136 0 0x14000 0x200 3 update 483950 88172 0 0x14000 0x200 2K cleaner *230917 43036 0 0x14000 0x200 1 reaper 0 0 0 0x10000 0x200 0 swapper db_enter() at panic+0x160 panic() at kdata_abort+0x17c do_el0_sync() at handle_el1h_sync+0x6c handle_el1h_sync() at proc_trampoline+0x4 proc_trampoline() at proc_trampoline+0x4 https://www.openbsd.org/ddb.html describes the minimum info required in bug reports. Insufficient info makes it difficult to find and fix bugs. ddb{1}> show panic cpu2: uvm_fault failed: ffffff7fcac92d0c esr 86000004 far ffffff7fcac92d0c *cpu1: attempt to access user address 0x2 from EL1 ddb{1}> trace db_enter() at panic+0x160 panic() at kdata_abort+0x17c do_el0_sync() at handle_el1h_sync+0x6c handle_el1h_sync() at proc_trampoline+0x4 proc_trampoline() at proc_trampoline+0x4 ddb{1}> ps PID TID PPID UID S FLAGS WAIT COMMAND 11561 15144 0 0 2 0x14200 smr 71445 249368 0 0 2 0x14200 zerothread 17852 252280 0 0 2 0x14200 aiodoned 82136 333802 0 0 7 0x14200 update 88172 483950 0 0 7 0x14200 cleaner *43036 230917 0 0 7 0x14200 reaper 42297 220576 0 0 2 0x14200 pagedaemon 59026 91905 0 0 3 0x14200 bored tztq 52314 54196 0 0 3 0x14200 bored wsdisplay0 79764 194460 0 0 3 0x14200 usbtsk usbtask 37015 55050 0 0 3 0x14200 usbatsk usbatsk 68043 391474 0 0 3 0x14200 mmctsk sdmmc2 49382 116874 0 0 3 0x14200 mmctsk sdmmc1 3160 512071 0 0 3 0x14200 mmctsk sdmmc0 14118 517952 0 0 3 0x14200 bored sensors 74887 515300 0 0 3 0x14200 bored sleep 18627 389142 0 0 1 0x14200 idle3 93959 276852 0 0 1 0x14200 idle2 64695 47893 0 0 1 0x14200 idle1 9472 329554 0 0 3 0x14200 bored softnet3 62505 89938 0 0 3 0x14200 bored softnet2
