Hi, i just got it back half working :-( dmesg | grep 2:0:1:1 [ 79.677949] scsi 2:0:1:1: Medium Changer NEC T40A2 0005 PQ: 0 ANSI: 2 [ 80.449402] ch 2:0:1:1: Attached scsi changer ch1 [ 80.449402] ch 2:0:1:1: Attached scsi generic sg6 type 8 [13387.819021] scsi 2:0:1:1: Medium Changer NEC T40A2 0005 PQ: 0 ANSI: 2 [13388.191786] ch 2:0:1:1: Attached scsi changer ch1 [13388.191786] ch 2:0:1:1: Attached scsi generic sg6 type 8
if i run mtx -f $device status i'll gett following messages mtx -f /dev/sg3 status mtx: Request Sense: Long Report=yes mtx: Request Sense: Valid Residual=no mtx: Request Sense: Error Code=70 (Current) mtx: Request Sense: Sense Key=Illegal Request mtx: Request Sense: FileMark=no mtx: Request Sense: EOM=no mtx: Request Sense: ILI=no mtx: Request Sense: Additional Sense Code = 24 mtx: Request Sense: Additional Sense Qualifier = 00 mtx: Request Sense: Field in Error = 05 mtx: Request Sense: BPV=yes mtx: Request Sense: Error in CDB=yes mtx: Request Sense: SKSV=yes mtx: Request Sense: Field Pointer = 00 02 Mode sense (0x1A) for Page 0x1D failed mtx: Request Sense: Long Report=yes mtx: Request Sense: Valid Residual=no mtx: Request Sense: Error Code=70 (Current) mtx: Request Sense: Sense Key=Illegal Request mtx: Request Sense: FileMark=no mtx: Request Sense: EOM=no mtx: Request Sense: ILI=no mtx: Request Sense: Additional Sense Code = 20 mtx: Request Sense: Additional Sense Qualifier = 00 mtx: Request Sense: Field in Error = 00 mtx: Request Sense: BPV=no mtx: Request Sense: Error in CDB=yes mtx: Request Sense: SKSV=yes mtx: Request Sense: Field Pointer = 00 00 READ ELEMENT STATUS Command Failed mtx -f /dev/sg4 status mtx: Request Sense: Long Report=yes mtx: Request Sense: Valid Residual=no mtx: Request Sense: Error Code=70 (Current) mtx: Request Sense: Sense Key=Illegal Request mtx: Request Sense: FileMark=no mtx: Request Sense: EOM=no mtx: Request Sense: ILI=no mtx: Request Sense: Additional Sense Code = 20 mtx: Request Sense: Additional Sense Qualifier = 00 mtx: Request Sense: Field in Error = 00 mtx: Request Sense: BPV=no mtx: Request Sense: Error in CDB=yes mtx: Request Sense: SKSV=yes mtx: Request Sense: Field Pointer = 00 00 READ ELEMENT STATUS Command Failed also on bat, the slots for the lto4 are not shown. slowly this become a little bit critical thanks andre On 25.05.2011 17:36, Mauro Colorio wrote: > try this > > dmesg | grep 2:0:1:1 > > it will tell you the name of the device where the loaders is attached > (sg3 in my case) > then > > mtx -f /dev/sg3 status > > if it works check ur config files > > Mauro > > ------------------------------------------------------------------------------ > vRanger cuts backup time in half-while increasing security. > With the market-leading solution for virtual backup and recovery, > you get blazing-fast, flexible, and affordable data protection. > Download your free trial now. > http://p.sf.net/sfu/quest-d2dcopy1 > _______________________________________________ > Bacula-users mailing list > Bacula-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/bacula-users ------------------------------------------------------------------------------ vRanger cuts backup time in half-while increasing security. With the market-leading solution for virtual backup and recovery, you get blazing-fast, flexible, and affordable data protection. Download your free trial now. http://p.sf.net/sfu/quest-d2dcopy1 _______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
