Hi,
On 5/10/2007 11:41 PM, Mike Vasquez wrote:
> Boy, I do need new glasses, Changer Command = "/opt/bacula/bin/mtx-changer
> %c %o %S %a %d".
>
> It should have been Changer Command = "/opt/bacula/scripts/mtx-changer %c
> %o %S %a %d"
Yeah, that's what you get for customizing your installation ;-) I can
assure you, though, that glasses don't necessarily help with this sort
of problems :-)
> Now I am getting the following error:
>
> bin/btape /dev/nst0
> Tape block granularity is 1024 bytes.
> btape: butil.c:286 Using device: "/dev/nst0" for writing.
> 10-May 14:26 btape: 3301 Issuing autochanger "loaded? drive 0" command.
> 10-May 14:26 btape: 3302 Autochanger "loaded? drive 0", result is Slot 1.
> 10-May 14:31 btape: Fatal Error at device.c:280 because:
> dev open failed: dev.c:425 Unable to open device "Drive-1" (/dev/nst0):
> ERR=Input/output error
>
> 10-May 14:31 btape: btape Fatal error: butil.c:195 Cannot open "Drive-1"
> (/dev/nst0)
Have you tried to access the tape drive as the user the SD runs as?
"permission denied" or "no such file" would be what I expected, but
"cannot open" might also indicate a permissions problem or, perhaps, the
tape is not fully loaded into the drive, or something.
Trying 'mt -f /dev/nst0 status' as the Bacula user should work, and if
it doesn't, it might tell us something...
Arno
> Here is the Drive-1 configuration.
> SD.conf file (New)
> Autochanger {
> Name = Autochanger
> Device = Drive-1
> Changer Command = "/opt/bacula/scripts/mtx-changer %c %o %S %a %d"
> Changer Device = /dev/sg0
> }
>
> Device {
> Name = Drive-1
> Drive Index = 0
> Media Type = LTO-1
> Archive Device = /dev/nst0
> AutomaticMount = yes;
> AlwaysOpen = yes;
> RemovableMedia = yes;
> RandomAccess = no;
> AutoChanger = yes
> Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
> }
>
> Any Ideas.
>
> Mike
>
> Arno Lehmann wrote:
>> Hi,
>>
>> On 5/10/2007 8:17 PM, Mike Vasquez wrote:
>>> I just upgraded to 2.0.3. I am having problems mounting the Autochanger.
>>> Here are my test results.
>>>
>>> tapeinfo -f /dev/sg0
>>> Product Type: Medium Changer
>>> Vendor ID: 'DELL '
>>> Product ID: 'PV-122T '
>>> Revision: 'D37r'
>>> Attached Changer: No
>>> SerialNumber: '3123B92743'
>>> Invalid tapealert page: 0
>>>
>>> mtx -f /dev/sg0 inquiry
>>> Product Type: Medium Changer
>>> Vendor ID: 'DELL '
>>> Product ID: 'PV-122T '
>>> Revision: 'D37r'
>>> Attached Changer: No
>>>
>>> /btape /dev/nst0
>>> Tape block granularity is 1024 bytes.
>>> btape: butil.c:286 Using device: "/dev/nst0" for writing.
>>> 10-May 10:20 btape: 3301 Issuing autochanger "loaded? drive 0" command.
>>> 10-May 10:20 btape: 3991 Bad autochanger "loaded? drive 0" command:
>>> ERR=No
>>> such file or directory.
>>> Results=
>>> ## It just hangs here.
>> Probably it doesn't find the mtx-changer script (or whatever it tries to
>> use in your case - I always use btabe with the SD configuration).
>>
>>> When I try to mount to take using the console here is what I get.
>>>
>>> SD.conf file
>>> Autochanger {
>>> Name = Autochanger
>>> Device = Drive-1
>>> Changer Command = "/opt/bacula/bin/mtx-changer %c %o %S %a %d"
>> Are you sure the Bacula user can run this script, and it works as
>> expected?
>>
>>> ChangerDevice = /dev/sg0
>>> }
>>>
>>> Device {
>>> Name = Drive-1 #
>>> Drive Index = 0
>>> Media Type = LTO-1
>>> Archive Device = /dev/nst0
>>> AutomaticMount = yes;
>>> AlwaysOpen = yes;
>>> RemovableMedia = yes;
>>> RandomAccess = no;
>>> AutoChanger = yes
>>> Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
>>> }
>> ...
>>> *mount ToTape
>>> Connecting to Storage daemon ToTape at nmc-sdca-mon1:9103 ...
>>> Enter autochanger slot: 1
>>> 3301 Issuing autochanger "loaded? drive 0" command.
>>> 3991 Bad autochanger "loaded? drive 0" command: ERR=No such file or
>>> directory.
>> Looks like the SD, too, can't run mtx-changer.
>>
>>> Results=
>>> 3301 Issuing autochanger "loaded? drive 0" command.
>>> 3991 Bad autochanger "loaded? drive 0" command: ERR=No such file or
>>> directory.
>>> Results=
>>> 3304 Issuing autochanger "load slot 1, drive 0" command.
>>> 3992 Bad autochanger "load slot 1, drive 0": ERR=No such file or
>>> directory.
>>> Results=
>>> 3301 Issuing autochanger "loaded? drive 0" command.
>>> 3991 Bad autochanger "loaded? drive 0" command: ERR=No such file or
>>> directory.
>>> Results=
>>> 3901 open device failed: ERR=dev.c:425 Unable to open device "ToTape.0"
>>> (/dev/nst0): ERR=Input/output error
>>>
>>> What could be wrong. It was working before I upgraded.
>> Permissions, probably. It's possible that, before the upgrade, the SD
>> ran as root and it now runs as a different user.
>>
>> Arno
>>
>>> Mike
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>> --
>> IT-Service Lehmann [EMAIL PROTECTED]
>> Arno Lehmann http://www.its-lehmann.de
>>
>> -------------------------------------------------------------------------
>> This SF.net email is sponsored by DB2 Express
>> Download DB2 Express C - the FREE version of DB2 express and take
>> control of your XML. No limits. Just data. Click to get it now.
>> http://sourceforge.net/powerbar/db2/
>> _______________________________________________
>> Bacula-users mailing list
>> Bacula-users@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/bacula-users
>>
>>
>
--
IT-Service Lehmann [EMAIL PROTECTED]
Arno Lehmann http://www.its-lehmann.de
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take
control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
