Hmmzz,
Houston we have a problem. This is a SATA drive so hooking it up to a
SCSI HBA is impossible.
If i run the diagnostic tests of the Quantum DLT Sage Talk, read and
write actions are working perfectly. If the drivers was bad, this should
fail also.
I guess that Bacula only supports SCSI tape drives?
On ma, 2007-04-02 at 13:14 +0200, Kern Sibbald wrote:
> I suspect that you have a bad driver. I don't think I have ever seen a
> non-SCSI tape driver that works correctly, probably because they are written
> by disk driver programmers that don't understand the subtleties of tape
> drivers.
>
> I'd recommend that if possible you hook your drive up through a good SCSI
> card.
>
> On Monday 02 April 2007 00:28, Sebastiaan Veldhuisen wrote:
> > Minor update.
> >
> > I tried the bacula 2.0.0-1 debs and redid the btape fill. At the end I
> > get the following in my kernel.log:
> >
> > Apr 2 00:10:17 debian kernel: st0: Current [descriptor]: sense key:
> > Hardware Error
> > Apr 2 00:10:17 debian kernel: Additional sense: No additional sense
> > information
> > Apr 2 00:10:17 debian kernel: Descriptor sense data with sense
> > descriptors (in hex):
> > Apr 2 00:10:17 debian kernel: 72 04 00 00 00 00 00 0e 09 0e 00
> > 52 00 03 00 00
> > Apr 2 00:10:17 debian kernel: 00 00 00 00 a0 51
> > Apr 2 00:10:19 debian kernel: ata2.00: exception Emask 0x0 SAct 0x0
> > SErr 0x0 action 0x0
> > Apr 2 00:10:19 debian kernel: ata2.00: (BMDMA stat 0x20)
> > Apr 2 00:10:19 debian kernel: ata2.00: tag 0 cmd 0xa0 Emask 0x1 stat
> > 0x51 err 0x52 (device error)
> > Apr 2 00:10:19 debian kernel: ata2: EH complete
> > Apr 2 00:10:19 debian kernel: st0: Current [descriptor]: sense key:
> > Hardware Error
> > Apr 2 00:10:19 debian kernel: Additional sense: No additional sense
> > information
> > Apr 2 00:10:19 debian kernel: Descriptor sense data with sense
> > descriptors (in hex):
> > Apr 2 00:10:19 debian kernel: 72 04 00 00 00 00 00 0e 09 0e 00
> > 52 00 03 00 00
> > Apr 2 00:10:19 debian kernel: 00 00 00 00 a0 51
> > Apr 2 00:10:21 debian kernel: ata2.00: exception Emask 0x0 SAct 0x0
> > SErr 0x0 action 0x0
> > Apr 2 00:10:21 debian kernel: ata2.00: (BMDMA stat 0x20)
> > Apr 2 00:10:21 debian kernel: ata2.00: tag 0 cmd 0xa0 Emask 0x1 stat
> > 0x51 err 0x52 (device error)
> > Apr 2 00:10:21 debian kernel: ata2: EH complete
> > Apr 2 00:10:21 debian kernel: st0: Current [descriptor]: sense key:
> > Hardware Error
> > Apr 2 00:10:21 debian kernel: Additional sense: No additional sense
> > information
> > Apr 2 00:10:21 debian kernel: Descriptor sense data with sense
> > descriptors (in hex):
> > Apr 2 00:10:21 debian kernel: 72 04 00 00 00 00 00 0e 09 0e 00
> > 52 00 03 00 00
> > Apr 2 00:10:21 debian kernel: 00 00 00 00 a0 51
> > Apr 2 00:10:23 debian kernel: ata2.00: exception Emask 0x0 SAct 0x0
> > SErr 0x0 action 0x0
> > Apr 2 00:10:23 debian kernel: ata2.00: (BMDMA stat 0x20)
> > Apr 2 00:10:23 debian kernel: ata2.00: tag 0 cmd 0xa0 Emask 0x1 stat
> > 0x51 err 0x52 (device error)
> > Apr 2 00:10:23 debian kernel: ata2: EH complete
> > Apr 2 00:10:23 debian kernel: st0: Current [descriptor]: sense key:
> > Hardware Error
> > Apr 2 00:10:23 debian kernel: Additional sense: No additional sense
> > information
> > Apr 2 00:10:23 debian kernel: Descriptor sense data with sense
> > descriptors (in hex):
> > Apr 2 00:10:23 debian kernel: 72 04 00 00 00 00 00 0e 09 0e 00
> > 52 00 03 00 00
> > Apr 2 00:10:23 debian kernel: 00 00 00 00 a0 51
> > Apr 2 00:10:25 debian kernel: ata2.00: exception Emask 0x0 SAct 0x0
> > SErr 0x0 action 0x0
> > Apr 2 00:10:25 debian kernel: ata2.00: tag 0 cmd 0xa0 Emask 0x1 stat
> > 0x51 err 0x52 (device error)
> > Apr 2 00:10:25 debian kernel: ata2: EH complete
> > Apr 2 00:10:25 debian kernel: st0: Current [descriptor]: sense key:
> > Hardware Error
> > Apr 2 00:10:25 debian kernel: Additional sense: No additional sense
> > information
> > Apr 2 00:10:25 debian kernel: Descriptor sense data with sense
> > descriptors (in hex):
> > Apr 2 00:10:25 debian kernel: 72 04 00 00 00 00 00 0e 09 0e 00
> > 52 00 03 00 00
> > Apr 2 00:10:25 debian kernel: 00 00 00 20 a0 51
> >
> >
> > My question is: is my problem is Bacula or kernel related?
> >
> > Thanks for your time
> >
> > Sebastiaan
> >
> > On zo, 2007-04-01 at 11:02 +0200, Sebastiaan Veldhuisen wrote:
> > > Hi,
> > >
> > > I'm trying to get a Quantum DLT-V4 SATA to work on my Debian Etch Bacula
> > > setup. My knowledge about Linux is good, but I don't have a lot of
> > > experience with Tape drives and/ or Bacula. Did a lot of testing with
> > > btape (as in days), but it is still not working. I'm really done with
> > > testing, therefore my hope is targeted at some gurus on the mailinglist
> > > that can tell me what is wrong (or what I am doing wrong).
> > > Any help would be great!
> > >
> > > Some notes:
> > > If I schedule a backup inside Bacula it works (completes successfully).
> > > I can't do a restore, which gives me the same errors as with btape.
> > >
> > > -------------------------------
> > > *version
> > > -------------------------------
> > > debian-dir Version: 1.38.11 (28 June 2006)
> > >
> > > -------------------------------
> > > debian:~# cat /proc/scsi/scsi
> > > -------------------------------
> > > Attached devices:
> > > Host: scsi0 Channel: 00 Id: 00 Lun: 00
> > > Vendor: ATA Model: SAMSUNG SP1614C Rev: SW10
> > > Type: Direct-Access ANSI SCSI revision: 05
> > > Host: scsi1 Channel: 00 Id: 00 Lun: 00
> > > Vendor: QUANTUM Model: DLT-V4 Rev: 0800
> > > Type: Sequential-Access ANSI SCSI revision: 02
> > >
> > > -------------------------------
> > > debian:~# cat /etc/stinit.def
> > > -------------------------------
> > > # QUANTUM DLT-V4
> > > manufacturer=QUANTUM model="DLT-V4" {
> > > timeout=3600
> > > long-timeout=14400
> > > can-partitions=0
> > > drive-buffering=1
> > > no-wait=0
> > > buffering=0
> > > async-writes=0
> > > read-ahead=0
> > > two-fms=0
> > > auto-lock=0
> > > fast-eom=0
> > > can-bsr=1
> > > noblklimits=0
> > > mode1 blocksize=0 density=0x51 compression=1 # DLT-V4 density,
> > > compression on
> > > }
> > >
> > > -------------------------------
> > > device section from bacula-sd.conf:
> > > -------------------------------
> > > Device {
> > > Name = DLT-V4
> > > Media Type = DLT
> > > Archive Device = /dev/nst0
> > > LabelMedia = yes;
> > > AutomaticMount = yes; # when device opened, read it
> > > AlwaysOpen = no;
> > > RemovableMedia = yes;
> > > RandomAccess = no;
> > > # too bad, tapeinfo not supported on this device :(
> > > #Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
> > > }
> > >
> > > -------------------------------
> > > When i do a btape test, everything seems ok:
> > > -------------------------------
> > > === Write, rewind, and re-read test ===
> > >
> > > I'm going to write 1000 records and an EOF
> > > then write 1000 records and an EOF, then rewind,
> > > and re-read the data to verify that it is correct.
> > >
> > > This is an *essential* feature ...
> > >
> > > btape: btape.c:795 Wrote 1000 blocks of 64412 bytes.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:811 Wrote 1000 blocks of 64412 bytes.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:820 Rewind OK.
> > > 1000 blocks re-read correctly.
> > > Got EOF on tape.
> > > 1000 blocks re-read correctly.
> > > === Test Succeeded. End Write, rewind, and re-read test ===
> > >
> > >
> > > === Write, rewind, and position test ===
> > >
> > > I'm going to write 1000 records and an EOF
> > > then write 1000 records and an EOF, then rewind,
> > > and position to a few blocks and verify that it is correct.
> > >
> > > This is an *essential* feature ...
> > >
> > > btape: btape.c:907 Wrote 1000 blocks of 64412 bytes.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:923 Wrote 1000 blocks of 64412 bytes.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:932 Rewind OK.
> > > Reposition to file:block 0:4
> > > Block 5 re-read correctly.
> > > Reposition to file:block 0:200
> > > Block 201 re-read correctly.
> > > Reposition to file:block 0:999
> > > Block 1000 re-read correctly.
> > > Reposition to file:block 1:0
> > > Block 1001 re-read correctly.
> > > Reposition to file:block 1:600
> > > Block 1601 re-read correctly.
> > > Reposition to file:block 1:999
> > > Block 2000 re-read correctly.
> > > === Test Succeeded. End Write, rewind, and re-read test ===
> > >
> > >
> > >
> > > === Append files test ===
> > >
> > > This test is essential to Bacula.
> > >
> > > I'm going to write one record in file 0,
> > > two records in file 1,
> > > and three records in file 2
> > >
> > > btape: btape.c:438 Rewound "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:338 open device "DLT-V4" (/dev/nst0): OK
> > > btape: btape.c:438 Rewound "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1061 Now moving to end of medium.
> > > btape: btape.c:490 Moved to end of medium.
> > > We should be in file 3. I am at file 3. This is correct!
> > >
> > > Now the important part, I am going to attempt to append to the tape.
> > >
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:438 Rewound "DLT-V4" (/dev/nst0)
> > > Done appending, there should be no I/O errors
> > >
> > > Doing Bacula scan of blocks:
> > > 1 block of 64448 bytes in file 1
> > > End of File mark.
> > > 2 blocks of 64448 bytes in file 2
> > > End of File mark.
> > > 3 blocks of 64448 bytes in file 3
> > > End of File mark.
> > > 1 block of 64448 bytes in file 4
> > > End of File mark.
> > > Total files=4, blocks=7, bytes = 451,136
> > > End scanning the tape.
> > > We should be in file 4. I am at file 4. This is correct!
> > >
> > > The above Bacula scan should have output identical to what follows.
> > > Please double check it ...
> > > === Sample correct output ===
> > > 1 block of 64448 bytes in file 1
> > > End of File mark.
> > > 2 blocks of 64448 bytes in file 2
> > > End of File mark.
> > > 3 blocks of 64448 bytes in file 3
> > > End of File mark.
> > > 1 block of 64448 bytes in file 4
> > > End of File mark.
> > > Total files=4, blocks=7, bytes = 451,136
> > > === End sample correct output ===
> > >
> > > If the above scan output is not identical to the
> > > sample output, you MUST correct the problem
> > > or Bacula will not be able to write multiple Jobs to
> > > the tape.
> > >
> > >
> > > === Write, backup, and re-read test ===
> > >
> > > I'm going to write three records and an EOF
> > > then backup over the EOF and re-read the last record.
> > > Bacula does this after writing the last block on the
> > > tape to verify that the block was written correctly.
> > >
> > > This is not an *essential* feature ...
> > >
> > > btape: btape.c:438 Rewound "DLT-V4" (/dev/nst0)
> > > btape: btape.c:674 Wrote first record of 64412 bytes.
> > > btape: btape.c:685 Wrote second record of 64412 bytes.
> > > btape: btape.c:696 Wrote third record of 64412 bytes.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:712 Backspaced over EOF OK.
> > > btape: btape.c:717 Backspace record OK.
> > > btape: btape.c:735
> > > Block re-read correct. Test succeeded!
> > > === End Write, backup, and re-read test ===
> > >
> > >
> > >
> > > === Forward space files test ===
> > >
> > > This test is essential to Bacula.
> > >
> > > I'm going to write five files then test forward spacing
> > >
> > > btape: btape.c:438 Rewound "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1531 Wrote one record of 64412 bytes.
> > > btape: btape.c:1533 Wrote block to device.
> > > btape: btape.c:469 Wrote 1 EOF to "DLT-V4" (/dev/nst0)
> > > btape: btape.c:438 Rewound "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1276 Now forward spacing 1 file.
> > > We should be in file 1. I am at file 1. This is correct!
> > > btape: btape.c:1288 Now forward spacing 2 files.
> > > We should be in file 3. I am at file 3. This is correct!
> > > btape: btape.c:438 Rewound "DLT-V4" (/dev/nst0)
> > > btape: btape.c:1301 Now forward spacing 4 files.
> > > We should be in file 4. I am at file 4. This is correct!
> > >
> > > btape: btape.c:1319 Now forward spacing 1 more file.
> > > We should be in file 5. I am at file 5. This is correct!
> > >
> > > === End Forward space files test ===
> > >
> > >
> > > -------------------------------
> > > However the fill test gives me the following error:
> > > -------------------------------
> > > 01-Apr 10:14 btape: btape Error: block.c:538 Write error at 216:694 on
> > > device "DLT-V4" (/dev/nst0). ERR=Input/output error.
> > > 01-Apr 10:14 btape: btape Error: Error writing final EOF to tape. This
> > > Volume may not be readable.
> > > dev.c:1542 ioctl MTWEOF error on "DLT-V4" (/dev/nst0). ERR=Input/output
> > > error.
> > > btape: btape.c:2301 Last block at: 216:693 this_dev_block_num=694
> > > btape: btape.c:2335 End of tape 216:694. VolumeCapacity=148,615,818,480.
> > > Write rate = 9076.9 KB/s
> > > Done writing ...
> > > Wrote state file last_block_num1=693 last_block_num2=0
> > >
> > > -------------------------------
> > > With the above btape error, a kernel error is also presented:
> > > -------------------------------
> > > Apr 1 10:39:42 debian kernel: ata2.00: qc timeout (cmd 0xa0)
> > > Apr 1 10:39:42 debian kernel: ata2.00: exception Emask 0x0 SAct 0x0
> > > SErr 0x0 action 0x2 frozen
> > > Apr 1 10:39:42 debian kernel: ata2.00: (BMDMA stat 0x20)
> > > Apr 1 10:39:42 debian kernel: ata2.00: tag 0 cmd 0xa0 Emask 0x5 stat
> > > 0x51 err 0x51 (timeout)
> > > Apr 1 10:39:49 debian kernel: ata2: port is slow to respond, please be
> > > patient
> > > Apr 1 10:40:12 debian kernel: ata2: port failed to respond (30 secs)
> > > Apr 1 10:40:12 debian kernel: ata2: soft resetting port
> > > Apr 1 10:40:13 debian kernel: ata2: SATA link up 1.5 Gbps (SStatus 113
> > > SControl 300)
> > > Apr 1 10:40:13 debian kernel: ata2.00: configured for UDMA/133
> > > Apr 1 10:40:13 debian kernel: ata2: EH complete
> > > Apr 1 10:40:13 debian kernel: st0: Current [descriptor]: sense key:
> > > Medium Error
> > > Apr 1 10:40:13 debian kernel: Additional sense: Address mark not
> > > found for data field
> > > Apr 1 10:40:13 debian kernel: Descriptor sense data with sense
> > > descriptors (in hex):
> > > Apr 1 10:40:13 debian kernel: 72 03 13 00 00 00 00 0e 09 0e 00
> > > 51 00 03 00 00
> > > Apr 1 10:40:13 debian kernel: 00 00 00 00 a0 51
> > > Apr 1 10:40:25 debian kernel: st0: Current: sense key: Unit Attention
> > > Apr 1 10:40:25 debian kernel: Additional sense: Scsi bus reset
> > > occurred
> > > Apr 1 10:41:08 debian kernel: ata2.00: qc timeout (cmd 0xa0)
> > > Apr 1 10:41:08 debian kernel: ata2.00: exception Emask 0x0 SAct 0x0
> > > SErr 0x0 action 0x2 frozen
> > > Apr 1 10:41:08 debian kernel: ata2.00: (BMDMA stat 0x20)
> > > Apr 1 10:41:08 debian kernel: ata2.00: tag 0 cmd 0xa0 Emask 0x5 stat
> > > 0x51 err 0x51 (timeout)
> > > Apr 1 10:41:15 debian kernel: ata2: port is slow to respond, please be
> > > patient
> > > Apr 1 10:41:39 debian kernel: ata2: port failed to respond (30 secs)
> > > Apr 1 10:41:39 debian kernel: ata2: soft resetting port
> > > Apr 1 10:41:39 debian kernel: ata2: SATA link up 1.5 Gbps (SStatus 113
> > > SControl 300)
> > > Apr 1 10:41:39 debian kernel: ata2.00: configured for UDMA/133
> > > Apr 1 10:41:39 debian kernel: ata2: EH complete
> > > Apr 1 10:41:39 debian kernel: st0: Current [descriptor]: sense key:
> > > Medium Error
> > > Apr 1 10:41:39 debian kernel: Additional sense: Address mark not
> > > found for data field
> > > Apr 1 10:41:39 debian kernel: Descriptor sense data with sense
> > > descriptors (in hex):
> > > Apr 1 10:41:39 debian kernel: 72 03 13 00 00 00 00 0e 09 0e 00
> > > 51 00 03 00 00
> > > Apr 1 10:41:39 debian kernel: 00 00 00 00 a0 51
> > >
> > > I tried appending "irqpoll acpi=noirq" to see wether it is a kernel
> > > problem, but that didn't make any difference. As writing seems to work,
> > > I guess it is not a kernel problem.
> > >
> > > --
> > > Regards,
> > >
> > > Sebastiaan
> > >
> > >
> > > -------------------------------------------------------------------------
> > > Take Surveys. Earn Cash. Influence the Future of IT
> > > Join SourceForge.net's Techsay panel and you'll get the chance to share
> your
> > > opinions on IT & business topics through brief surveys-and earn cash
> > > http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
> > > _______________________________________________
> > > Bacula-users mailing list
> > > Bacula-users@lists.sourceforge.net
> > > https://lists.sourceforge.net/lists/listinfo/bacula-users
> > --
> > Met vriendelijke groeten,
> >
> > Sebastiaan Veldhuisen
> > Arsenso B.V.
> > Europalaan 16
> > 2408 BG Alphen aan den Rijn
> > T: 0172-49 14 16
> > F: 0712-49 14 04
> > E: [EMAIL PROTECTED]
> >
> >
> > -------------------------------------------------------------------------
> > Take Surveys. Earn Cash. Influence the Future of IT
> > Join SourceForge.net's Techsay panel and you'll get the chance to share your
> > opinions on IT & business topics through brief surveys-and earn cash
> > http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
> > _______________________________________________
> > Bacula-users mailing list
> > Bacula-users@lists.sourceforge.net
> > https://lists.sourceforge.net/lists/listinfo/bacula-users
> >
--
Met vriendelijke groeten,
Sebastiaan Veldhuisen
Arsenso B.V.
Europalaan 16
2408 BG Alphen aan den Rijn
T: 0172-49 14 16
F: 0712-49 14 04
E: [EMAIL PROTECTED]
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
