Tomorrow I will create the same config in my lab. Keep you posted.
On Oct 31, 2011, at 11:03 PM, Rodrigo Ricardo Passos wrote: > Gustavo, > > I configure the informations like carrier sent to me. > The linkset nothing more than my local identification, ok? > > Follow the real configuration? > > linkset=1 > pointcode=12538 > defaultdpc=3979 > adjpointcode=3979 > > cicbeginswith=1 > networkindicator=national > sigchan=16 > channel=1-15,17-31 > > linkset=2 > pointcode=12538 > defaultdpc=163 > adjpointcode=163 > > cicbeginswith=1 > networkindicator=national > channel=32-62 > > linkset=3 > pointcode=12538 > defaultdpc=160 > adjpointcode=160 > > cicbeginswith=1 > networkindicator=national > channel=63-93 > > linkset=4 > pointcode=12538 > defaultdpc=3980 > adjpointcode=3980 > > cicbeginswith=1 > networkindicator=national > sigchan=108 > channel=94-107,110-124 > > The channel 109 has moved because the 16 channel in NEAX is reserverd. > > Em 31/10/2011 23:54, Gustavo Mársico escreveu: >> Rodrigo >> >> I give you just and example, did you get all the information from the >> carrier about the SPCs? >> >> >> On Oct 31, 2011, at 10:35 PM, Rodrigo Ricardo Passos wrote: >> >>> Gustavo, >>> >>> Thanks for your response. >>> >>> I make the configuration like you recommend, and the problem persist. >>> With the first E1, the call is ok, but with the least E1, the call is >>> completed, but doesn't have audio. >>> Other information is, the asterisk cannot create linkset 2 and 3 because >>> this linksets doesn't have sigchan and when I place a call using these >>> channels, asterisk crash with a segment fault. >>> I'm with asterisk 1.8.6.0 and libss7 1.0.2. >>> >>> Regards, >>> >>> Rodrigo Passos >>> >>> >>> Em 31/10/2011 22:59, Gustavo Mársico escreveu: >>>> Just to mention, Alcatel S12 and Neax 61E aren't softswitches, they're >>>> good old fashion TDM switches. >>>> >>>> If you need to ITX with 4 different switches you will need at least 4 SPC, >>>> and you defined just 2 (80 as STP and 100 as SP). >>>> >>>> Guessing that S12_01 and NEAX_02 are acting as STP for S12_02 and NEAX_01, >>>> and assuming S12_01 is 80, S12_02 is 100, NEAX_01 is 120 and NEAX_02 is >>>> 140, it should be something like this: >>>> >>>> ;s12_01 >>>> ;because you've cic's with S12_01 >>>> linkset=1 >>>> pointcode=80 >>>> adjpointcode=80 >>>> >>>> cicbeginswith = 1 >>>> networkindicator=national >>>> sigchan = 16 >>>> channel = 1-15,17-31 >>>> >>>> ;s12_02 >>>> ;just cics >>>> linkset=2 >>>> pointcode=100 >>>> adjpointcode=80 'STP s12_01 >>>> defaultdpc=80 >>>> >>>> cicbeginswith = 1 >>>> networkindicator=national >>>> channel = 32-62 >>>> >>>> ;neax_01 >>>> ;just cics >>>> linkset=3 >>>> pointcode=120 >>>> adjpointcode=140 'STP neax_02 >>>> defaultdpc=140 >>>> >>>> cicbeginswith = 1 >>>> networkindicator=national >>>> channel = 63-93 >>>> >>>> ;neax_02 >>>> ;because you've cic's with neax_02 >>>> linkset=4 >>>> pointcode=140 >>>> adjpointcode=140 >>>> >>>> cicbeginswith = 1 >>>> networkindicator=national >>>> sigchan = 109 >>>> channel = 94-108,110-124 >>>> >>>> >>>> In any case, you can use 1-31 as CIC in that scenario, you just need to >>>> get the proper information to define the linksets. >>>> >>>> Regards >>>> >>>> Gustavo >>>> >>>> >>>> On Oct 31, 2011, at 8:13 PM, Rodrigo Ricardo Passos wrote: >>>> >>>>> Hi all, >>>>> >>>>> I have the following scenario: >>>>> >>>>> The telco company uses 4 different Softswitchs to compose my SS7 >>>>> interconnection, so 4 E1s to have redundancy. Each this one uses >>>>> channels 1 up to 31. The map of the firsts is equal the ID of the >>>>> asterisk channels, but the next ID´s isn't the same and the signaling >>>>> doesn't work. The telco cannot change the CIC configuration to have the >>>>> same CIC in my configuration. I have one TE405P. The only way to solve >>>>> this problem is change the CIC in the telco company or i can change CIC >>>>> maps in my asterisk box? Only the first E1 align with the first >>>>> softswitch. When I a place a call using channel 64 of my third E1, telco >>>>> doesn't have CIC 64, but have CIC 2 and the cannot be complete because >>>>> the CIC isn't the same. What is the solution? >>>>> >>>>> First E1: Asterisk: 1 - 31 (16 signaling) - Alcatel: S12_01 1-31 (16 >>>>> signaling) >>>>> Second E1 Asterisk: 32 - 62 (no signaling - voice only) - Alcatel: S12_02 >>>>> 1 - 31 >>>>> Third E1: Asterisk: 63 - 93 (no signaling - voice only) - NEC: NEAX_01 1 >>>>> - 31 >>>>> Fourth E1: Asterisk: 94 - 124 (16 signaling) - NEC: NEAX_02 1 - 31 >>>>> >>>>> All dpcs are different; each this one have an unique ID for each E1, only >>>>> problem is the signaling. >>>>> My configurations are: >>>>> >>>>> system.conf: >>>>> span=1,1,0,ccs,hdb3 >>>>> # termtype: unknown >>>>> bchan=1-15,17-31 >>>>> mtp2=16 >>>>> >>>>> # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS >>>>> span=2,1,0,ccs,hdb3 >>>>> # termtype: unknown >>>>> bchan=32-62 >>>>> >>>>> # Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" HDB3/CCS >>>>> span=3,1,0,ccs,hdb3 >>>>> # termtype: unknown >>>>> bchan=63-93 >>>>> >>>>> # Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4" HDB3/CCS >>>>> span=4,1,0,ccs,hdb3 >>>>> # termtype: unknown >>>>> bchan=94-107,110-124 >>>>> mtp2=108 >>>>> >>>>> # Global data >>>>> >>>>> loadzone = us >>>>> defaultzone = us >>>>> >>>>> >>>>> chan_dahdi.conf: >>>>> >>>>> [trunkgroups] >>>>> >>>>> [channels] >>>>> context=interconexoes >>>>> ss7type=itu >>>>> signalling=ss7 >>>>> ss7_called_nai=dynamic >>>>> ss7_calling_nai=dynamic >>>>> networkindicator=national >>>>> echotraining=yes >>>>> echotraining=800 >>>>> echocancel=yes >>>>> >>>>> group=1 >>>>> >>>>> linkset=1 >>>>> pointcode=100 >>>>> defaultdpc=80 >>>>> adjpointcode=80 >>>>> >>>>> cicbeginswith=1 >>>>> channel=1-15 >>>>> cicbeginswith=17 >>>>> channel=17-31 >>>>> sigchan=16 >>>>> >>>>> cicbeginswith=32 >>>>> channel=32-62 >>>>> >>>>> pointcode=100 >>>>> defaultdpc=90 >>>>> adjpointcode=90 >>>>> >>>>> cicbeginswith=63 >>>>> channel=63-93 >>>>> >>>>> cicbeginswith=94 >>>>> channel=94-107 >>>>> cicbeginswith=110 >>>>> channel=110-124 >>>>> sigchan=108 >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> -- >>>>> _____________________________________________________________________ >>>>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>>>> >>>>> asterisk-ss7 mailing list >>>>> To UNSUBSCRIBE or update options visit: >>>>> http://lists.digium.com/mailman/listinfo/asterisk-ss7 >>>> -- >>>> _____________________________________________________________________ >>>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>>> >>>> asterisk-ss7 mailing list >>>> To UNSUBSCRIBE or update options visit: >>>> http://lists.digium.com/mailman/listinfo/asterisk-ss7 >>>> >>> -- >>> _____________________________________________________________________ >>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>> >>> asterisk-ss7 mailing list >>> To UNSUBSCRIBE or update options visit: >>> http://lists.digium.com/mailman/listinfo/asterisk-ss7 >> >> -- >> _____________________________________________________________________ >> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >> >> asterisk-ss7 mailing list >> To UNSUBSCRIBE or update options visit: >> http://lists.digium.com/mailman/listinfo/asterisk-ss7 >> > > -- > _____________________________________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
