Rodrigo I give you just and example, did you get all the information from the carrier about the SPCs?
On Oct 31, 2011, at 10:35 PM, Rodrigo Ricardo Passos wrote: > > Gustavo, > > Thanks for your response. > > I make the configuration like you recommend, and the problem persist. > With the first E1, the call is ok, but with the least E1, the call is > completed, but doesn't have audio. > Other information is, the asterisk cannot create linkset 2 and 3 because this > linksets doesn't have sigchan and when I place a call using these channels, > asterisk crash with a segment fault. > I'm with asterisk 1.8.6.0 and libss7 1.0.2. > > Regards, > > Rodrigo Passos > > > Em 31/10/2011 22:59, Gustavo Mársico escreveu: >> Just to mention, Alcatel S12 and Neax 61E aren't softswitches, they're good >> old fashion TDM switches. >> >> If you need to ITX with 4 different switches you will need at least 4 SPC, >> and you defined just 2 (80 as STP and 100 as SP). >> >> Guessing that S12_01 and NEAX_02 are acting as STP for S12_02 and NEAX_01, >> and assuming S12_01 is 80, S12_02 is 100, NEAX_01 is 120 and NEAX_02 is 140, >> it should be something like this: >> >> ;s12_01 >> ;because you've cic's with S12_01 >> linkset=1 >> pointcode=80 >> adjpointcode=80 >> >> cicbeginswith = 1 >> networkindicator=national >> sigchan = 16 >> channel = 1-15,17-31 >> >> ;s12_02 >> ;just cics >> linkset=2 >> pointcode=100 >> adjpointcode=80 'STP s12_01 >> defaultdpc=80 >> >> cicbeginswith = 1 >> networkindicator=national >> channel = 32-62 >> >> ;neax_01 >> ;just cics >> linkset=3 >> pointcode=120 >> adjpointcode=140 'STP neax_02 >> defaultdpc=140 >> >> cicbeginswith = 1 >> networkindicator=national >> channel = 63-93 >> >> ;neax_02 >> ;because you've cic's with neax_02 >> linkset=4 >> pointcode=140 >> adjpointcode=140 >> >> cicbeginswith = 1 >> networkindicator=national >> sigchan = 109 >> channel = 94-108,110-124 >> >> >> In any case, you can use 1-31 as CIC in that scenario, you just need to get >> the proper information to define the linksets. >> >> Regards >> >> Gustavo >> >> >> On Oct 31, 2011, at 8:13 PM, Rodrigo Ricardo Passos wrote: >> >>> Hi all, >>> >>> I have the following scenario: >>> >>> The telco company uses 4 different Softswitchs to compose my SS7 >>> interconnection, so 4 E1s to have redundancy. Each this one uses channels >>> 1 up to 31. The map of the firsts is equal the ID of the asterisk channels, >>> but the next ID´s isn't the same and the signaling doesn't work. The telco >>> cannot change the CIC configuration to have the same CIC in my >>> configuration. I have one TE405P. The only way to solve this problem is >>> change the CIC in the telco company or i can change CIC maps in my asterisk >>> box? Only the first E1 align with the first softswitch. When I a place a >>> call using channel 64 of my third E1, telco doesn't have CIC 64, but have >>> CIC 2 and the cannot be complete because the CIC isn't the same. What is >>> the solution? >>> >>> First E1: Asterisk: 1 - 31 (16 signaling) - Alcatel: S12_01 1-31 (16 >>> signaling) >>> Second E1 Asterisk: 32 - 62 (no signaling - voice only) - Alcatel: S12_02 1 >>> - 31 >>> Third E1: Asterisk: 63 - 93 (no signaling - voice only) - NEC: NEAX_01 1 - >>> 31 >>> Fourth E1: Asterisk: 94 - 124 (16 signaling) - NEC: NEAX_02 1 - 31 >>> >>> All dpcs are different; each this one have an unique ID for each E1, only >>> problem is the signaling. >>> My configurations are: >>> >>> system.conf: >>> span=1,1,0,ccs,hdb3 >>> # termtype: unknown >>> bchan=1-15,17-31 >>> mtp2=16 >>> >>> # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" HDB3/CCS >>> span=2,1,0,ccs,hdb3 >>> # termtype: unknown >>> bchan=32-62 >>> >>> # Span 3: TE4/0/3 "T4XXP (PCI) Card 0 Span 3" HDB3/CCS >>> span=3,1,0,ccs,hdb3 >>> # termtype: unknown >>> bchan=63-93 >>> >>> # Span 4: TE4/0/4 "T4XXP (PCI) Card 0 Span 4" HDB3/CCS >>> span=4,1,0,ccs,hdb3 >>> # termtype: unknown >>> bchan=94-107,110-124 >>> mtp2=108 >>> >>> # Global data >>> >>> loadzone = us >>> defaultzone = us >>> >>> >>> chan_dahdi.conf: >>> >>> [trunkgroups] >>> >>> [channels] >>> context=interconexoes >>> ss7type=itu >>> signalling=ss7 >>> ss7_called_nai=dynamic >>> ss7_calling_nai=dynamic >>> networkindicator=national >>> echotraining=yes >>> echotraining=800 >>> echocancel=yes >>> >>> group=1 >>> >>> linkset=1 >>> pointcode=100 >>> defaultdpc=80 >>> adjpointcode=80 >>> >>> cicbeginswith=1 >>> channel=1-15 >>> cicbeginswith=17 >>> channel=17-31 >>> sigchan=16 >>> >>> cicbeginswith=32 >>> channel=32-62 >>> >>> pointcode=100 >>> defaultdpc=90 >>> adjpointcode=90 >>> >>> cicbeginswith=63 >>> channel=63-93 >>> >>> cicbeginswith=94 >>> channel=94-107 >>> cicbeginswith=110 >>> channel=110-124 >>> sigchan=108 >>> >>> >>> >>> >>> >>> -- >>> _____________________________________________________________________ >>> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >>> >>> asterisk-ss7 mailing list >>> To UNSUBSCRIBE or update options visit: >>> http://lists.digium.com/mailman/listinfo/asterisk-ss7 >> >> -- >> _____________________________________________________________________ >> -- Bandwidth and Colocation Provided by http://www.api-digital.com -- >> >> asterisk-ss7 mailing list >> To UNSUBSCRIBE or update options visit: >> http://lists.digium.com/mailman/listinfo/asterisk-ss7 >> > > -- > _____________________________________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7 -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
