Well, I do not have that piece of hardware. I did install one of 6.8, 6.9, 7.0 or 7.1 on Lime2 with fresh u-boot back then and I was able to boot well. Which OpenBSD are you using on Lime2? Maybe I can use the older one for now.
Thanking you Sagar Acharya Nov 17, 2022, 14:46 by jan.de.kr...@gmail.com: > That last line is the same when I boot. > > But this picture seems to tell me that you have hooked up an HDMI screen. > > To see the full boot you need to wire up the debug uart via an rs232 > converter and use terminal software on some other computer. > See the Olimex manual. > > Once X is enabled you will see this on the HDMI output and a while later > the X login screen. > j. > > > On Thu, Nov 17, 2022 at 3:07 PM Sagar Acharya <sagaracha...@tutanota.com> > wrote: > >> I face the same issue. Attaching image alongside. >> Thanking you >> Sagar Acharya >> >> >> 17 Nov 2022, 18:31 by jan.de.kr...@gmail.com: >> >> > Yes, it is. >> > j. >> > >> > >> > On Thu, Nov 17, 2022 at 1:40 PM Sagar Acharya <sagaracha...@tutanota.com >> > >> > wrote: >> > >> >> I'll try it out. I was assuming that since cubieboard also has A20, >> things >> >> would work straightaway. Are device trees same across GNU/Linux and >> OpenBSD? >> >> >> >> Thanking you >> >> Sagar Acharya >> >> >> >> >> >> Nov 17, 2022, 11:42 by jan.de.kr...@gmail.com: >> >> >> >> > I am running armv7/7.2 on this board. >> >> > This is how I got it to run: >> >> > >> >> > from one of the images at >> >> > >> >> > https://images.olimex.com/release/a20/ >> >> > >> >> > you extract >> >> > /usr/lib/linux-image-5.10.105-olimex/sun7i-a20-olinuxino-lime2.dtb >> (or >> >> the >> >> > other one if your board is that way) >> >> > >> >> > I put it in the root of the EFI (dos) partition, which is 'p1' on my >> >> image. >> >> > >> >> > and you extract >> >> > /usr/lib/u-boot-olinuxino/a20-olinuxino/u-boot-sunxi-with-spl.bin >> >> > >> >> > it must go onto the image you created for bsd, in the usual place. >> >> > j. >> >> > >> >> > On Thu, Nov 17, 2022 at 10:46 AM Sagar Acharya < >> >> sagaracha...@tutanota.com> >> >> > wrote: >> >> > >> >> >> I finally recognized the beauty of OpenBSD with extremely easy >> configs >> >> of >> >> >> OpenSMTPD, doas, xenocara, and many more such softwares. I have been >> a >> >> dev >> >> >> at Hyperbola soon to be HyperbolaBSD. >> >> >> >> >> >> I was trying to install OpenBSD Lime2. I tried flashing cubieboard >> image >> >> >> of miniroot followed by flashing u-boot as shown in installation >> >> >> instructions. I built a fresh binary from 2022.10 release of u-boot. >> >> >> >> >> >> dd if=miniroot-cubie.img of=/dev/sda bs=1M conv=sync >> >> >> dd if=u-boot-sunxi-with-spl.bin of=/dev/sda bs=1024 seek=8 >> >> >> >> >> >> u-boot tries to search for /etc/random.seed which it doesn't find. >> There >> >> >> are just 2 files, bsd and bsd.mp . After the prompt, >> >> >> "EHCI fails to shut down host controller", a completely black screen >> >> turns >> >> >> up. So, I'm unable to get the kernel booted. Kindly help. >> >> >> >> >> >> Thanking you >> >> >> Sagar Acharya >> >> >> >> >> >>
