hi all,
it's been a while since i've had enough issues with getting obsd
installed that it warranted a post to one of the lists. i have seen
sthen post boot messages from a known-working rpi 4b rev 1.2, but i have
a rpi 4b rev 1.4 here that has a mostly-broken bse0 and does not work
with uboot.
when booting 6.8, the uefi firmware + miniroot configuration boots fine,
bse0 pulls an ip properly via dhclient, but when it comes time to fetch
the sets via https the transfer goes glacially slow. as in it would take
many hours or days to pull the installation files down. i worked around
this by writing the install files to another usb storage device, so it
is indeed possible to complete the installation in a timely fashion.
however, on a reboot, the problem with bse0 barely working persists.
i have confirmed that this problem occurs both with the ACPI and
devicetree settings in the uefi firmware.
i suspect that the rev 1.4 has some hardware change relative to rev 1.2
that is not obvious. i have included the miniroot boot messsages at the
end of this email.
when booting the 210418 snapshot, i followed the new instructions and
uboot goes into a loop and never gets to booting miniroot. the messages
are included below.
i think there is little else i can do myself to make this work at this
point. i look forward to any suggestions.
NOTE: i'm not subscribed to the list, so make sure to reply to me as a cc.
regards,
jake
OpenBSD 6.8 (RAMDISK) #780: Sun Oct 4 20:57:28 MDT 2020
dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/RAMDISK
real mem = 1995489280 (1903MB)
avail mem = 1901342720 (1813MB)
random: good seed from bootblocks
mainbus0 at root: Raspberry Pi 4 Model B Rev 1.4
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu0: 1024KB 64b/line 16-way L2 cache
efi0 at mainbus0: UEFI 2.7
efi0: https://github.com/pftf/RPi4 rev 0x10000
"system" at mainbus0 not configured
"axi" at mainbus0 not configured
simplebus0 at mainbus0: "soc"
bcmclock0 at simplebus0
bcmmbox0 at simplebus0
bcmgpio0 at simplebus0
bcmaux0 at simplebus0
ampintc0 at simplebus0 nirq 256, ncpu 4: "interrupt-controller"
syscon0 at simplebus0: "avs-monitor"
"thermal" at syscon0 not configured
bcmdmac0 at simplebus0: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7 DMA8 DMA9
"timer" at simplebus0 not configured
bcmirng0 at simplebus0
pluart0 at simplebus0: console
com0 at simplebus0: ns16550, no working fifo
"local_intc" at simplebus0 not configured
bcmdog0 at simplebus0
simplebus1 at simplebus0: "firmware"
"clocks" at simplebus1 not configured
"gpio" at simplebus1 not configured
"power" at simplebus0 not configured
"mailbox" at simplebus0 not configured
sdhc0 at simplebus0
sdhc0: SDHC 3.0, 250 MHz base clock
sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
"gpiomem" at simplebus0 not configured
"fb" at simplebus0 not configured
"vcsm" at simplebus0 not configured
"clocks" at mainbus0 not configured
"phy" at mainbus0 not configured
simplebus2 at mainbus0: "emmc2bus"
sdhc1 at simplebus2
sdhc1: SDHC 3.0, 100 MHz base clock
sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed, ddr52, dma
"arm-pmu" at mainbus0 not configured
agtimer0 at mainbus0: tick rate 54000 KHz
simplebus3 at mainbus0: "scb"
bcmpcie0 at simplebus3
pci0 at bcmpcie0
ppb0 at pci0 dev 0 function 0 "Broadcom BCM2711" rev 0x10
pci1 at ppb0 bus 1
xhci0 at pci1 dev 0 function 0 "VIA VL805 xHCI" rev 0x01: intx, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "VIA xHCI root hub" rev
3.00/1.00 addr 1
bse0 at simplebus3: address e4:5f:01:07:1d:fe
brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
"dma" at simplebus3 not configured
"hevc-decoder" at simplebus3 not configured
"rpivid-local-intc" at simplebus3 not configured
"h264-decoder" at simplebus3 not configured
"vp9-decoder" at simplebus3 not configured
"leds" at mainbus0 not configured
"sd_io_1v8_reg" at mainbus0 not configured
"fixedregulator_3v3" at mainbus0 not configured
"fixedregulator_5v0" at mainbus0 not configured
simplebus4 at mainbus0: "v3dbus"
"clk-108M" at mainbus0 not configured
"sd_vcc_reg" at mainbus0 not configured
sdmmc1: can't enable card
uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub"
rev 2.10/4.21 addr 2
umass0 at uhub0 port 3 configuration 1 interface 0 "Genesys USB3 Reader"
rev 3.00/0.01 addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Generic, STORAGE DEVICE, FT01> removable
serial.05e30738000000000001
sd0: 15192MB, 512 bytes/sector, 31113216 sectors
scsibus1 at sdmmc0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SD16G, 0020> removable
sd1: 15192MB, 512 bytes/sector, 31113216 sectors
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
gpio at bcmgpio0 not configured
U-Boot 2021.01 (Apr 16 2021 - 15:39:01 +1000)
DRAM: 1.9 GiB
RPI 4 Model B (0xb03114)
MMC: mmcnr@7e300000: 1, emmc2@7e340000: 0
Loading Environment from FAT... *** Warning - bad CRC, using default
environment
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@7d580000
PCIe BRCM: link up, 5.0 Gbps x1 (SSC)
starting USB...
Bus xhci_pci: probe failed, error -110
No working controllers found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
"Synchronous Abort" handler, esr 0x96000044
elr: 000000000009bca0 lr : 000000000009c8ac (reloc)
elr: 000000003b377ca0 lr : 000000003b3788ac
x0 : 616353206f686365 x1 : 000000000000000a
x2 : 000000003b3d30e0 x3 : 0000000000000002
x4 : 000000003af62410 x5 : 000000003af62430
x6 : 0000000000000021 x7 : 000000003b3d30a0
x8 : 000000003aff2a00 x9 : 0000000000000008
x10: 000000003af61a20 x11: 000000003af66ca0
x12: 0000000000000000 x13: 0000000000000200
x14: 000000003af4be78 x15: 0000000000000002
x16: 0000000000004110 x17: 0000007ffffc2228
x18: 000000003af57da0 x19: 000000003af62420
x20: 000000003af62420 x21: 0000000000000020
x22: 000000003b3d30f0 x23: 000000003b3d3000
x24: 0000000000000003 x25: 0000000000000030
x26: 000000003af62410 x27: 0000000000000000
x28: 000000003af61460 x29: 000000003af4abd0
Code: 8b21cc42 f85f0440 a9010880 f9000844 (f9000c04)
Resetting CPU ...
