Set your uefi firmware to device tree or acpi + device tree mode.
On 2021/01/13 01:25, tech-lists wrote:
> On Wed, Jan 13, 2021 at 03:56:22PM +0100, Mark Kettenis wrote:
> > > Date: Wed, 13 Jan 2021 01:06:30 +0000
> > > From: tech-lists <tech-li...@zyxst.net>
> > >
> > > Hi,
> > >
> > > On Wed, Jan 13, 2021 at 10:43:57PM +0800, Archimedes Gaviola wrote:
> > > >Hi,
> > > >
> > > >Can you try this in your system?
> > > >
> > > >openbsdrpi4b2# sysctl -a | grep temp0
> > > >hw.sensors.bcmtmon0.temp0=55.99 degC
> > >
> > > obsd# sysctl -a | grep temp0
> > > obsd#
> >
> > Show us your dmesg!
> >
>
> OK was worried it'd be too long. Here it is:
>
> OpenBSD 6.8 (GENERIC.MP) #3: Thu Jan 7 07:35:28 MST 2021
>
> r...@syspatch-68-arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP
> real mem = 8375504896 (7987MB)
> avail mem = 8085917696 (7711MB)
> random: good seed from bootblocks
> mainbus0 at root: ACPI
> psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
> cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
> cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu0: 1024KB 64b/line 16-way L2 cache
> cpu1 at mainbus0 mpidr 1: ARM Cortex-A72 r0p3
> cpu1: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu1: 1024KB 64b/line 16-way L2 cache
> cpu2 at mainbus0 mpidr 2: ARM Cortex-A72 r0p3
> cpu2: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu2: 1024KB 64b/line 16-way L2 cache
> cpu3 at mainbus0 mpidr 3: ARM Cortex-A72 r0p3
> cpu3: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu3: 1024KB 64b/line 16-way L2 cache
> efi0 at mainbus0: UEFI 2.7
> efi0: https://github.com/pftf/RPi4 rev 0x10000
> smbios0 at efi0: SMBIOS 3.3.0
> smbios0: vendor https://github.com/pftf/RPi4 version "UEFI Firmware v1.22"
> date 01/06/2021
> smbios0: Raspberry Pi Foundation Raspberry Pi 4 Model B
> apm0 at mainbus0
> ampintc0 at mainbus0 nirq 256, ncpu 4 ipi: 0, 1: "interrupt-controller"
> agtimer0 at mainbus0: tick rate 54000 KHz
> acpi0 at mainbus0: ACPI 6.3
> acpi0: sleep states
> acpi0: tables DSDT FACP CSRT DBG2 GTDT IORT APIC PPTT SPCR
> acpi0: wakeup devices
> "BCM2849" at acpi0 not configured
> "BCM2835" at acpi0 not configured
> "BCM2854" at acpi0 not configured
> "ACPI0004" at acpi0 not configured
> xhci0 at acpi0 XHC0 addr 0x600000000/0x1000 irq 175, xHCI 1.0
> usb0 at xhci0: USB revision 3.0
> uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev
> 3.00/1.00 addr 1
> "ACPI0007" at acpi0 not configured
> "ACPI0007" at acpi0 not configured
> "ACPI0007" at acpi0 not configured
> "ACPI0007" at acpi0 not configured
> "ACPI0004" at acpi0 not configured
> "BCM2848" at acpi0 not configured
> "BCM2850" at acpi0 not configured
> "BCM2856" at acpi0 not configured
> "BCM2845" at acpi0 not configured
> "BCM2841" at acpi0 not configured
> "BCM2841" at acpi0 not configured
> "BCM2838" at acpi0 not configured
> "BCM2839" at acpi0 not configured
> "BCM2844" at acpi0 not configured
> pluart0 at acpi0 URT0 addr 0xfe201000/0x1000 irq 153: console
> "BCM2836" at acpi0 not configured
> "BCM2EA6" at acpi0 not configured
> "MSFT8000" at acpi0 not configured
> "BCM2847" at acpi0 not configured
> "BCM2855" at acpi0 not configured
> bse0 at acpi0 ETH0 addr 0xfd580000/0x10000 irq 189: address dc:a6:32:e2:48:fc
> brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
> "PNP0C06" at acpi0 not configured
> acpitz at acpi0 not configured
> uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub" rev
> 2.10/4.21 addr 2
> uhidev0 at uhub1 port 3 configuration 1 interface 0 "Logitech USB Receiver"
> rev 2.00/29.01 addr 3
> uhidev0: iclass 3/1
> ukbd0 at uhidev0: 8 variable keys, 6 key codes
> wskbd0 at ukbd0 mux 1
> uhidev1 at uhub1 port 3 configuration 1 interface 1 "Logitech USB Receiver"
> rev 2.00/29.01 addr 3
> uhidev1: iclass 3/1, 17 report ids
> ums0 at uhidev1 reportid 2: 16 buttons, Z and W dir
> wsmouse0 at ums0 mux 0
> uhid0 at uhidev1 reportid 3: input=4, output=0, feature=0
> uhid1 at uhidev1 reportid 4: input=1, output=0, feature=0
> uhid2 at uhidev1 reportid 16: input=6, output=6, feature=0
> uhid3 at uhidev1 reportid 17: input=19, output=19, feature=0
> umass0 at uhub0 port 3 configuration 1 interface 0 "USB SanDisk 3.2Gen1" rev
> 3.20/1.00 addr 4
> umass0: using SCSI over Bulk-Only
> scsibus0 at umass0: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <USB, SanDisk 3.2Gen1, 1.00> removable
> serial.078155838107b4280bcc
> sd0: 29340MB, 512 bytes/sector, 60088320 sectors
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> bootfile: sd0a:/bsd
> boot device: sd0
> root on sd0a (e5a43b2d7fd9d217.a) swap on sd0b dump on sd0b
> WARNING: clock lost 6 days
> WARNING: CHECK AND RESET THE DATE!
> wskbd0 detached
> ukbd0 detached
> uhidev0 detached
> wsmouse0 detached
> ums0 detached
> uhid0 detached
> uhid1 detached
> uhid2 detached
> uhid3 detached
> uhidev1 detached
> --
> J.
>
