Hello, I tried to install current on RockPro64 to eMMC.
_ I used the firmware provided by Marc (on microSD): https://marc.info/?l=openbsd-arm&m=156114869709200&w=2 _ I used an usb stick for miniroot Once arrived to choose the whole disk... Impossible to write the eMMC disk. I tried to force via reinit... without success. _ A reason ? (i will try (to validate the installation process) to install OpenBSD on the sd card. Thanks in advance. ******************** * Installation log * ******************** cu -s 115200 -l /dev/cuaU0 Connected to /dev/cuaU0 (speed 115200) U-Boot TPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31) Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200) Trying to boot from MMC1 NOTICE: BL31: v2.1(debug):2.1 NOTICE: BL31: Built : 21:16:08, Jul 4 2019 INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 INFO: plat_rockchip_pmu_init(1596): pd status 3e INFO: BL31: Initializing runtime services WARNING: BL31: cortex_a53: CPU workaround for 819472 was missing! WARNING: BL31: cortex_a53: CPU workaround for 824069 was missing! WARNING: BL31: cortex_a53: CPU workaround for 827319 was missing! INFO: BL31: cortex_a53: CPU workaround for 855873 was applied INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9 U-Boot 2019.10-rc2-00001-gdf33f86468-dirty (Aug 16 2019 - 22:31:31 +0200) Model: Pine64 RockPro64 DRAM: 3.9 GiB MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: Pine64 RockPro64 rockchip_dnl_key_pressed: adc_channel_single_shot fail! Net: Error: ethernet@fe300000 address not set. eth-1: ethernet@fe300000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0(part 0) is current device ** No partition table - mmc 0 ** switch to partitions #0, OK mmc1 is current device ** Invalid partition 1 ** starting USB... Bus usb@fe380000: USB EHCI 1.00 Bus usb@fe3c0000: USB EHCI 1.00 Bus dwc3: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus dwc3: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@fe380000 for devices... 2 USB Device(s) found scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Device 0: Vendor: Lexar Rev: 1100 Prod: USB Flash Drive Type: Removable Hard Disk Capacity: 7634.0 MB = 7.4 GB (15634432 x 512) ... is now current device Scanning usb 0:1... Found EFI removable media binary efi/boot/bootaa64.efi libfdt fdt_check_header(): FDT_ERR_BADMAGIC Scanning disk dw...@fe320000.blk... Scanning disk sd...@fe330000.blk... Scanning disk usb_mass_storage.lun0... Found 5 disks BootOrder not defined EFI boot manager: Cannot load any image 165119 bytes read in 56 ms (2.8 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC disks: sd0* sd1 sd2 >> OpenBSD/arm64 BOOTAA64 0.20 boot> cannot open sd0a:/etc/random.seed: No such file or directory booting sd0a:/bsd: 2228484+623928+8770112+752864 [180632+109+521472+201593]=0xff1d68 Host not halted after 16000 microseconds. type 0x2 pa 0x200000 va 0x200000 pages 0x4000 attr 0x8 type 0x7 pa 0x4200000 va 0x4200000 pages 0x3eec attr 0x8 type 0x4 pa 0x80ec000 va 0x80ec000 pages 0x28 attr 0x8 type 0x7 pa 0x8114000 va 0x8114000 pages 0xec0a6 attr 0x8 type 0x2 pa 0xf41ba000 va 0xf41ba000 pages 0xc33 attr 0x8 type 0x7 pa 0xf4ded000 va 0xf4ded000 pages 0x1 attr 0x8 type 0x2 pa 0xf4dee000 va 0xf4dee000 pages 0x100 attr 0x8 type 0x1 pa 0xf4eee000 va 0xf4eee000 pages 0x29 attr 0x8 type 0x0 pa 0xf4f17000 va 0xf4f17000 pages 0x7 attr 0x8 type 0x4 pa 0xf4f1e000 va 0xf4f1e000 pages 0x1 attr 0x8 type 0x0 pa 0xf4f1f000 va 0xf4f1f000 pages 0x2 attr 0x8 type 0x6 pa 0xf4f21000 va 0xa3863000 pages 0x1 attr 0x8000000000000008 type 0x0 pa 0xf4f22000 va 0xf4f22000 pages 0x3 attr 0x8 type 0x4 pa 0xf4f25000 va 0xf4f25000 pages 0x2 attr 0x8 type 0x6 pa 0xf4f27000 va 0xa3869000 pages 0x1 attr 0x8000000000000008 type 0x2 pa 0xf4f28000 va 0xf4f28000 pages 0x3018 attr 0x8 type 0x5 pa 0xf7f40000 va 0xa6882000 pages 0x10 attr 0x8000000000000008 type 0x2 pa 0xf7f50000 va 0xf7f50000 pages 0xb0 attr 0x8 Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2019 OpenBSD. All rights reserved. https://www.OpenBSD.org OpenBSD 6.6-current (RAMDISK) #333: Thu Nov 28 01:12:25 MST 2019 dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/RAMDISK real mem = 4093190144 (3903MB) avail mem = 3891441664 (3711MB) mainbus0 at root: Pine64 RockPro64 cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu0: 512KB 64b/line 16-way L2 cache efi0 at mainbus0: UEFI 2.8 efi0: Das U-Boot rev 0x20191000 psci0 at mainbus0: PSCI 1.1, SMCCC 1.1 agintc0 at mainbus0 sec shift 3:3 nirq 288 nredist 6: "interrupt-controller" agintcmsi0 at agintc0 syscon0 at mainbus0: "qos" syscon1 at mainbus0: "qos" syscon2 at mainbus0: "qos" syscon3 at mainbus0: "qos" syscon4 at mainbus0: "qos" syscon5 at mainbus0: "qos" syscon6 at mainbus0: "qos" syscon7 at mainbus0: "qos" syscon8 at mainbus0: "qos" syscon9 at mainbus0: "qos" syscon10 at mainbus0: "qos" syscon11 at mainbus0: "qos" syscon12 at mainbus0: "qos" syscon13 at mainbus0: "qos" syscon14 at mainbus0: "qos" syscon15 at mainbus0: "qos" syscon16 at mainbus0: "qos" syscon17 at mainbus0: "qos" syscon18 at mainbus0: "qos" syscon19 at mainbus0: "qos" syscon20 at mainbus0: "qos" syscon21 at mainbus0: "qos" syscon22 at mainbus0: "qos" syscon23 at mainbus0: "qos" syscon24 at mainbus0: "qos" syscon25 at mainbus0: "power-management" "power-controller" at syscon25 not configured syscon26 at mainbus0: "syscon" "io-domains" at syscon26 not configured syscon27 at mainbus0: "syscon" syscon28 at mainbus0: "syscon" rkclock0 at mainbus0 rkclock1 at mainbus0 syscon29 at mainbus0: "syscon" "io-domains" at syscon29 not configured "usb2-phy" at syscon29 not configured "usb2-phy" at syscon29 not configured "phy" at syscon29 not configured rkpinctrl0 at mainbus0: "pinctrl" rkgpio0 at rkpinctrl0 rkgpio1 at rkpinctrl0 rkgpio2 at rkpinctrl0 rkgpio3 at rkpinctrl0 rkgpio4 at rkpinctrl0 "fit-images" at mainbus0 not configured "pmu_a53" at mainbus0 not configured "pmu_a72" at mainbus0 not configured agtimer0 at mainbus0: tick rate 24000 KHz "xin24m" at mainbus0 not configured simplebus0 at mainbus0: "amba" "dma-controller" at simplebus0 not configured "dma-controller" at simplebus0 not configured dwge0 at mainbus0: address ff:ff:ff:ff:ff:ff rgephy0 at dwge0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6 dwmmc0 at mainbus0: 50 MHz base clock sdmmc0 at dwmmc0: 4-bit, sd high-speed, mmc high-speed, dma sdhc0 at mainbus0 sdhc0: SDHC 3.0, 200 MHz base clock sdmmc1 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma ehci0 at mainbus0 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci0 at mainbus0: version 1.0 ehci1 at mainbus0 usb1 at ehci1: USB revision 2.0 uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci1 at mainbus0: version 1.0 rkdwusb0 at mainbus0: "usb" xhci0 at rkdwusb0, xHCI 1.10 usb2 at xhci0: USB revision 3.0 uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1 rkdwusb1 at mainbus0: "usb" xhci1 at rkdwusb1, xHCI 1.10 usb3 at xhci1: USB revision 3.0 uhub3 at usb3 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00 addr 1 "saradc" at mainbus0 not configured rkiic0 at mainbus0 iic0 at rkiic0 rkiic1 at mainbus0 iic1 at rkiic1 com0 at mainbus0: ns16550, no working fifo com1 at mainbus0: ns16550, no working fifo com1: console "thermal-zones" at mainbus0 not configured "tsadc" at mainbus0 not configured rkiic2 at mainbus0 iic2 at rkiic2 rkpmic0 at iic2 addr 0x1b: RK808 "silergy,syr827" at iic2 addr 0x40 not configured "silergy,syr828" at iic2 addr 0x41 not configured rkiic3 at mainbus0 iic3 at rkiic3 fusbtc0 at iic3 addr 0x22 "pwm" at mainbus0 not configured "pwm" at mainbus0 not configured "dmc" at mainbus0 not configured "efuse" at mainbus0 not configured "phy" at mainbus0 not configured "phy" at mainbus0 not configured "watchdog" at mainbus0 not configured "rktimer" at mainbus0 not configured "i2s" at mainbus0 not configured "i2s" at mainbus0 not configured "i2s" at mainbus0 not configured "vop" at mainbus0 not configured "iommu" at mainbus0 not configured "vop" at mainbus0 not configured "iommu" at mainbus0 not configured "hdmi" at mainbus0 not configured "gpu" at mainbus0 not configured "opp-table0" at mainbus0 not configured "opp-table1" at mainbus0 not configured "opp-table2" at mainbus0 not configured "external-gmac-clock" at mainbus0 not configured "gpio-keys" at mainbus0 not configured "leds" at mainbus0 not configured "sdio-pwrseq" at mainbus0 not configured "vcc12v-dcin" at mainbus0 not configured "vcc1v8-s3" at mainbus0 not configured "vcc3v3-pcie-regulator" at mainbus0 not configured "vcc3v3-sys" at mainbus0 not configured "vcc5v0-host-regulator" at mainbus0 not configured "vcc5v0-typec-regulator" at mainbus0 not configured "vcc5v0-sys" at mainbus0 not configured "vcc5v0-usb" at mainbus0 not configured "vdd-log" at mainbus0 not configured usb4 at ohci0: USB revision 1.0 uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 usb5 at ohci1: USB revision 1.0 uhub5 at usb5 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 scsibus0 at sdmmc0: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SC16G, 0080> removable sd0: 15193MB, 512 bytes/sector, 31116288 sectors scsibus1 at sdmmc1: 2 targets, initiator 0 sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4064, 0000> removable sd1: 59640MB, 512 bytes/sector, 122142720 sectors umass0 at uhub0 port 1 configuration 1 interface 0 "Lexar USB Flash Drive" rev 2.10/11.00 addr 2 umass0: using SCSI over Bulk-Only scsibus2 at umass0: 2 targets, initiator 0 sd2 at scsibus2 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> removable serial.05dca838E89K3FOCINZ7 sd2: 7634MB, 512 bytes/sector, 15634432 sectors softraid0 at root scsibus3 at softraid0: 256 targets bootfile: sd0a:/bsd boot device: sd0 root on rd0a swap on rd0b dump on rd0b WARNING: preposterous clock chip time WARNING: CHECK AND RESET THE DATE! erase ^?, werase ^W, kill ^U, intr ^C, status ^T Welcome to the OpenBSD/arm64 6.6 installation program. (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? I At any prompt except password prompts you can escape to a shell by typing '!'. Default answers are shown in []'s and are selected by pressing RETURN. You can exit this program at any time by pressing Control-C, but this can leave your system in an inconsistent state. Terminal type? [vt220] System hostname? (short form, e.g. 'foo') pinu Available network interfaces are: dwge0 vlan0. Which network interface do you wish to configure? (or 'done') [dwge0] IPv4 address for dwge0? (or 'dhcp' or 'none') [dhcp] dwge0: no link.... dwge0: xxx.xxx.xxx.12 lease accepted from xxx.xxx.xxx.254 (14:0c:xxx:xx:xx:xx) IPv6 address for dwge0? (or 'autoconf' or 'none') [none] autoconf Available network interfaces are: dwge0 vlan0. Which network interface do you wish to configure? (or 'done') [done] DNS domain name? (e.g. 'example.com') [my.domain] burelli.home Using DNS nameservers at xxx.xxx.xxx.254 8.8.8.8 Password for root account? (will not echo) Password for root account? (again) Start sshd(8) by default? [yes] Setup a user? (enter a lower-case loginname, or 'no') [no] olivier Full name for user olivier? [oliv] Olivier Burelli Password for user olivier? (will not echo) Password for user olivier? (again) WARNING: root is targeted by password guessing attacks, pubkeys are safer. Allow root ssh login? (yes, no, prohibit-password) [no] What timezone are you in? ('?' for list) [Europe/Paris] Available disks are: sd0 sd1 sd2. Which disk is the root disk? ('?' for details) [sd0] ? sd0: SD/MMC, SC16G, 0080 (14.8G) sd1: Sandisk, DA4064, 0000 (58.2G) sd2: Lexar, USB Flash Drive, 1100 serial.05dca838E89K3FOCINZ7 (7.5G) Available disks are: sd0 sd1 sd2. Which disk is the root disk? ('?' for details) [sd0] sd1 Disk: sd1 geometry: 7603/255/63 [122142720 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- 0: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 1: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 2: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 3: FF 267349 89 4 - 46077 37 38 [ 4294967295: 740229375 ] Xenix BBT Use (W)hole disk or (E)dit the MBR? [whole] e You will now create one MBR partition to contain your OpenBSD data and one MBR partition on which the OpenBSD boot program is located. Neither partition will overlap any other partition. The OpenBSD MBR partition will have an id of 'A6' and the boot MBR partition will have an id of 'C' (msdos). The boot partition will be at least 16MB and be the first 'MSDOS' partition on the disk. Disk: sd1 geometry: 7603/255/63 [122142720 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- 0: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 1: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 2: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 3: FF 267349 89 4 - 46077 37 38 [ 4294967295: 740229375 ] Xenix BBT Enter 'help' for information sd1: 1> reinit Disk: sd1 geometry: 7603/255/63 [122142720 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- 0: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused 1: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused *3: A6 0 1 2 - 7602 254 63 [ 64: 122142131 ] OpenBSD Use 'write' to update disk. sd1*: 1> write Writing MBR at offset 0. sd1: 1> q No OpenBSD partition in MBR, try again. Disk: sd1 geometry: 7603/255/63 [122142720 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- 0: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 1: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 2: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 3: FF 267349 89 4 - 46077 37 38 [ 4294967295: 740229375 ] Xenix BBT Use (W)hole disk or (E)dit the MBR? [whole] -- burelli.fr <oliv...@burelli.fr>
