On Wed, Aug 14, Mark Kettenis wrote:
> > Date: Tue, 13 Aug 2019 22:01:30 +0000
> > From: ioh <m...@sdf.org>
> >
> > On Tue, Aug 13, Mark Kettenis wrote:
> > > > Date: Tue, 13 Aug 2019 01:01:37 +0000
> > > > From: ioh <m...@sdf.org>
> > > >
> > > > On Mon, Aug 12, Mark Kettenis wrote:
> > > > > > Date: Sun, 11 Aug 2019 23:49:10 +0000
> > > > > > From: ioh <m...@sdf.org>
> > > > > >
> > > > > > I have been able to successfully install OpenBSD Current Aug 06
> > > > > > 2019 on the Olimex Teres laptop. It has very similar hardware to
> > > > > > the PineBook, arm64 allwinner, etc. I used
> > > > > > u-boot-sunxi-with-spl.bin
> > > > > > from u-boot v2019.07 (teres_i_defconfig) and Arm Trusted Firmware
> > > > > > v2.1. The dtb (sun50i-a64-teres-i.dtb) is from the OpenBSD
> > > > > > 6.5-release
> > > > > > ports tree.
> >
> > I took the latest linux v5.3-rc4 and added some basic ehci0 and
> > ohci0 nodes. I built the dtb with musl-cross-make and by running
> > make dtbs in the linux source tree:
> >
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
> > b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
> > index 1069e7012c9c..a8596d742d68 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
> > @@ -100,6 +100,11 @@
> > status = "okay";
> > };
> >
> > +&ehci0 {
> > + phys = <&usbphy 0>;
> > + status = "okay";
> > +};
> > +
> > &ehci1 {
> > status = "okay";
> > };
> > @@ -153,6 +158,11 @@
> > status = "okay";
> > };
> >
> > +&ohci0 {
> > + phys = <&usbphy 0>;
> > + status = "okay";
> > +};
> > +
> > &ohci1 {
> > status = "okay";
> > };
> >
> Right, now you need my latest commits!
>
> Latest snapshot kernel (dated Tue Aug 13) should be ok.
I dd'd the latest snapshot miniroot66.fs to a microsd with the
u-boot and atf as described above and the patched dts. It appears
the keyboard is recognized but no driver is attached. It also
appears the camera is not given the uvideo driver as it was before.
External usb nic and external flash drives work.
Here are the boot logs:
U-Boot SPL 2019.07 (Aug 06 2019 - 22:39:39 +0000)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.1(release):v2.1
NOTICE: BL31: Built : 22:20:23, Aug 6 2019
NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE: BL31: Found U-Boot DTB at 0x408a4a0, model: Olimex A64 Teres-I
NOTICE: BL31: PMIC: Detected AXP803 on RSB.
U-Boot 2019.07 (Aug 06 2019 - 22:39:39 +0000) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: Olimex A64 Teres-I
DRAM: 2 GiB
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... *** Warning - bad CRC, using default environment
In: serial
Out: vidconsole
Err: vidconsole
Net: No ethernet found.
starting USB...
Bus usb@1c1b000: USB EHCI 1.00
scanning bus usb@1c1b000 for devices...
USB device not accepting new address (error=2)
4 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
24363 bytes read in 5 ms (4.6 MiB/s)
Found EFI removable media binary efi/boot/bootaa64.efi
Scanning disk m...@1c0f000.blk...
Card did not respond to voltage select!
Scanning disk m...@1c10000.blk...
Disk m...@1c10000.blk not ready
Scanning disk m...@1c11000.blk...
Found 6 disks
BootOrder not defined
EFI boot manager: Cannot load any image
161122 bytes read in 12 ms (12.8 MiB/s)
disks: sd0* sd1
>> OpenBSD/arm64 BOOTAA64 0.18
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2202188+619932+8747640+741088
[220743+109+511728+198149]=0xff00c8
type 0x2 pa 0x40000000 va 0x40000000 pages 0x4000 attr 0x8
type 0x7 pa 0x44000000 va 0x44000000 pages 0x3ef7 attr 0x8
type 0x4 pa 0x47ef7000 va 0x47ef7000 pages 0x12 attr 0x8
type 0x7 pa 0x47f09000 va 0x47f09000 pages 0x702cc attr 0x8
type 0x2 pa 0xb81d5000 va 0xb81d5000 pages 0xd26 attr 0x8
type 0x1 pa 0xb8efb000 va 0xb8efb000 pages 0x28 attr 0x8
type 0x0 pa 0xb8f23000 va 0xb8f23000 pages 0x7 attr 0x8
type 0x6 pa 0xb8f2a000 va 0x3e024be000 pages 0x1 attr 0x8000000000000008
type 0x0 pa 0xb8f2b000 va 0xb8f2b000 pages 0x6 attr 0x8
type 0x6 pa 0xb8f31000 va 0x3e024c5000 pages 0x1 attr 0x8000000000000008
type 0x0 pa 0xb8f32000 va 0xb8f32000 pages 0x1 attr 0x8
type 0x2 pa 0xb8f33000 va 0xb8f33000 pages 0x501d attr 0x8
type 0x5 pa 0xbdf50000 va 0x3e074e4000 pages 0x10 attr 0x8000000000000008
type 0x2 pa 0xbdf60000 va 0xbdf60000 pages 0xa0 attr 0x8
type 0x0 pa 0xbe000000 va 0xbe000000 pages 0x401 attr 0x8
type 0x2 pa 0xbe401000 va 0xbe401000 pages 0x1bff attr 0x8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2019 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.6-beta (RAMDISK) #162: Mon Aug 12 21:05:24 MDT 2019
dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/RAMDISK
real mem = 2015113216 (1921MB)
avail mem = 1920393216 (1831MB)
mainbus0 at root: Olimex A64 Teres-I
cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu0: 512KB 64b/line 16-way L2 cache
efi0 at mainbus0: UEFI 2.7
efi0: Das U-Boot rev 0x20190700
psci0 at mainbus0: PSCI 1.1, SMCCC 1.1
"osc24M_clk" at mainbus0 not configured
"osc32k_clk" at mainbus0 not configured
"pmu" at mainbus0 not configured
"sound" at mainbus0 not configured
"sound_spdif" at mainbus0 not configured
"spdif-out" at mainbus0 not configured
agtimer0 at mainbus0: tick rate 24000 KHz
simplebus0 at mainbus0: "soc"
sxisyscon0 at simplebus0
sxiccmu0 at simplebus0
sxipio0 at simplebus0: 103 pins
ampintc0 at simplebus0 nirq 224, ncpu 4: "interrupt-controller"
sxirtc0 at simplebus0
sxiccmu1 at simplebus0
sxipio1 at simplebus0: 13 pins
sxirsb0 at simplebus0
"x-powers,axp803" at sxirsb0 addr 0x3a3 not configured
"bus" at simplebus0 not configured
"dma-controller" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"video-codec" at simplebus0 not configured
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
sximmc1 at simplebus0
sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma
sximmc2 at simplebus0
sdmmc2 at sximmc2: 8-bit, sd high-speed, mmc high-speed, dma
"eeprom" at simplebus0 not configured
"phy" at simplebus0 not configured
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ohci0 at simplebus0: version 1.0
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00
addr 1
ohci1 at simplebus0: version 1.0
"dai" at simplebus0 not configured
"codec" at simplebus0 not configured
com0 at simplebus0: ns16550, no working fifo
com0: console
sxitwi0 at simplebus0
iic0 at sxitwi0
"gpu" at simplebus0 not configured
"pwm" at simplebus0 not configured
"hdmi-phy" at simplebus0 not configured
"interrupt-controller" at simplebus0 not configured
"codec-analog" at simplebus0 not configured
"watchdog" at simplebus0 not configured
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio1: 32 pins
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00
addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00
addr 1
"backlight" at mainbus0 not configured
"gpio-keys" at mainbus0 not configured
"leds" at mainbus0 not configured
"usb1-vbus" at mainbus0 not configured
"wifi_pwrseq" at mainbus0 not configured
"audio-amplifier" at mainbus0 not configured
simplefb0 at mainbus0: 1366x768, 32bpp
wsdisplay0 at simplefb0
wsdisplay0: screen 0 added (std, vt100 emulation)
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SDCIT, 0030> SCSI2 0/direct removable
sd0: 7464MB, 512 bytes/sector, 15286272 sectors
manufacturer 0x024c, product 0xb723 at sdmmc1 function 1 not configured
scsibus1 at sdmmc2: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Micron, R1J56L, 0000> SCSI2 0/direct removable
sd1: 14080MB, 512 bytes/sector, 28835840 sectors
uhub4 at uhub1 port 1 configuration 1 interface 0 "Genesys Logic USB2.0 Hub"
rev 2.00/85.36 addr 2
urtwn0 at uhub4 port 2 configuration 1 interface 0 "Realtek 802.11n NIC" rev
2.00/0.00 addr 3
urtwn0: MAC/BB RTL8188EU, RF 6052 1T1R, address 84:16:f9:1d:70:5c
"Generic USB2.0 PC CAMERA" rev 2.00/1.00 addr 4 at uhub4 port 3 not configured
"Olimex Ltd. TERES Keyboard+Touchpad (drv)" rev 1.10/0.01 addr 5 at uhub4 port
4 not configured
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/arm64 6.6 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell?
--
ioh
