That usually means that either a) the interrupts don’t arrive or b) the timer/hardclock doesn’t tick.
Do your debug printfs print on interrupt? If not, try to add that and see if there are any interrupts at all. Patrick > Am 11.10.2015 um 18:13 schrieb Leonardo Guardati <leona...@guardati.it>: > > I believe I'm almost there. > > To circumvent the problem of the previous email (where > it hung on driver deferred autoconfiguration), > I had to disable the usb drivers on the RAMDISK > kernel config. > > The bsd.rd kernel is now reaching the /sbin/init > executable, but its code wont run! > > I'm sure about this because if I remove the > /sbin/init file from the mr.fs ramdisk image, then the > process gracefully reboots because it doesn't find > the init file. > > I've put some debugging printfs showing the sys/kern/init_main.c > code execution...it goes smooth...no error. > > The problems I think is on the sys_execve() call. > > But I need some insight/suggestion on where to look. > > Here the console output: > > U-Boot SPL 2015.10-rc4-00050-g996ec1d (Oct 04 2015 - 13:27:50) > DRAM: 1024 MiB > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > > > U-Boot 2015.10-rc4-00050-g996ec1d (Oct 04 2015 - 13:27:50 +0200) Allwinner > Technology > > CPU: Allwinner A20 (SUN7I) > I2C: ready > DRAM: 1 GiB > MMC: SUNXI SD/MMC: 0 > *** Warning - bad CRC, using default environment > > In: serial > Out: serial > Err: serial > SCSI: SUNXI SCSI INIT > SATA link 0 timeout. > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > flags: ncq stag pm led clo only pmp pio slum part ccc apst > Net: eth0: ethernet@01c50000 > starting USB... > USB0: USB EHCI 1.00 > USB1: USB OHCI 1.0 > USB2: USB EHCI 1.00 > USB3: USB OHCI 1.0 > scanning bus 0 for devices... 1 USB Device(s) found > scanning bus 2 for devices... 1 USB Device(s) found > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > Found U-Boot script /boot.scr > reading /boot.scr > 189 bytes read in 17 ms (10.7 KiB/s) > ## Executing script at 43100000 > reading bsd.umg > 5688048 bytes read in 294 ms (18.5 MiB/s) > ## Booting kernel from Legacy Image at 40200000 ... > Image Name: boot > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 5687984 Bytes = 5.4 MiB > Load Address: 40300000 > Entry Point: 40300000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > > Starting kernel ... > > > OpenBSD/sunxi booting ... > arg0 0x0 arg1 0x10bb arg2 0x40000100 > atag core flags 0 pagesize 0 rootdev 0 > atag serial 0x16516604:080264c0 > atag cmdline [rd0a:] > atag mem start 0x40000000 size 0x40000000 > bootfile: rd0a: > bootargs: > memory size derived from u-boot > bootconf.mem[0].address = 40000000 pages 262144/0x40000000 > physmemory: 262144 pages at 0x40000000 -> 0x7fffffff > Allocating page tables > freestart = 0x4086d000, free_pages = 259987 (0x0003f793) > IRQ stack: p0x4089b000 v0xc089b000 > ABT stack: p0x4089c000 v0xc089c000 > UND stack: p0x4089d000 v0xc089d000 > SVC stack: p0x4089e000 v0xc089e000 > Creating L1 page table at 0x40870000 > Mapping kernel > Constructing L2 page tables > undefined page pmap [ using 251020 bytes of bsd ELF symbol table ] > board type: 4283 > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org > > OpenBSD 5.8-current (RAMDISK) #8: Sun Oct 11 17:53:06 CEST 2015 > r...@foo.my.domain:/usr/src/sys/arch/armv7/compile/RAMDISK > real mem = 1073741824 (1024MB) > avail mem = 1043972096 (995MB) > mainbus0 at root > cortex0 at mainbus0 > ampintc0 at cortex0 nirq 160 > agtimer0 at cortex0: tick rate 24000 KHz > cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core) > cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled > cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache > sunxi0 at mainbus0: Allwinner A20 > sxipio0 at sunxi0 > sxiccmu0 at sunxi0 > sxitimer0 at sunxi0: ticktimer 100hz @ 32KHz > sxitimer1 at sunxi0: stattimer 128hz @ 32KHz > sxitimer2 at sunxi0: cntrtimer @ 32KHz > sxidog0 at sunxi0: ctrl 0 mode 0 > > sxirtc0 at sunxi0 > sxiuart0 at sunxi0: consoleenable irq 33 register 104 bitmask 00000002 > > sxiuart1 at sunxi0enable irq 34 register 104 bitmask 00000004 > > sxiuart2 at sunxi0enable irq 35 register 104 bitmask 00000008 > > sxiuart3 at sunxi0enable irq 36 register 104 bitmask 00000010 > > sxiuart4 at sunxi0enable irq 49 register 104 bitmask 00020000 > > sxiuart5 at sunxi0enable irq 50 register 104 bitmask 00040000 > > sxiuart6 at sunxi0enable irq 51 register 104 bitmask 00080000 > > sxiuart7 at sunxi0enable irq 52 register 104 bitmask 00100000 > > sxie0 at sunxi0enable irq 87 register 108 bitmask 00800000 > , address 02:04:08:02:64:c0 > rgephy0 at sxie0 phy 0: RTL8169S/8110S/8211 PHY, rev. 5 > rgephy1 at sxie0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5 > ahci0 at sunxi0enable irq 88 register 108 bitmask 01000000 > AHCI 1.1 > scsibus0 at ahci0: 32 targets > sunxi0: device ehci unit 0 not configured > sunxi0: device ehci unit 1 not configured > port 0 pin 0 cfg 2 > port 0 pin 1 cfg 2 > port 0 pin 2 cfg 2 > port 0 pin 3 cfg 2 > port 0 pin 4 cfg 2 > port 0 pin 5 cfg 2 > port 0 pin 6 cfg 2 > port 0 pin 7 cfg 2 > port 0 pin 8 cfg 2 > port 0 pin 9 cfg 2 > port 0 pin 10 cfg 2 > port 0 pin 11 cfg 2 > port 0 pin 12 cfg 2 > port 0 pin 13 cfg 2 > port 0 pin 14 cfg 2 > port 0 pin 15 cfg 2 > port 0 pin 16 cfg 2 > port 0 pin 17 cfg 2 > gpio0 at sxipio0: 18 pins > port 1 pin 0 cfg 2 > port 1 pin 1 cfg 2 > port 1 pin 2 cfg 0 > port 1 pin 3 cfg 0 > port 1 pin 4 cfg 0 > port 1 pin 5 cfg 0 > port 1 pin 6 cfg 0 > port 1 pin 7 cfg 0 > port 1 pin 8 cfg 1 > port 1 pin 9 cfg 0 > port 1 pin 10 cfg 0 > port 1 pin 11 cfg 0 > port 1 pin 12 cfg 0 > port 1 pin 13 cfg 0 > port 1 pin 14 cfg 0 > port 1 pin 15 cfg 0 > port 1 pin 16 cfg 0 > port 1 pin 17 cfg 0 > port 1 pin 18 cfg 0 > port 1 pin 19 cfg 0 > port 1 pin 20 cfg 0 > port 1 pin 21 cfg 0 > port 1 pin 22 cfg 2 > port 1 pin 23 cfg 2 > gpio1 at sxipio0: 24 pins > port 2 pin 0 cfg 0 > port 2 pin 1 cfg 0 > port 2 pin 2 cfg 0 > port 2 pin 3 cfg 0 > port 2 pin 4 cfg 0 > port 2 pin 5 cfg 0 > port 2 pin 6 cfg 0 > port 2 pin 7 cfg 0 > port 2 pin 8 cfg 0 > port 2 pin 9 cfg 0 > port 2 pin 10 cfg 0 > port 2 pin 11 cfg 0 > port 2 pin 12 cfg 0 > port 2 pin 13 cfg 0 > port 2 pin 14 cfg 0 > port 2 pin 15 cfg 0 > port 2 pin 16 cfg 0 > port 2 pin 17 cfg 0 > port 2 pin 18 cfg 0 > port 2 pin 19 cfg 0 > port 2 pin 20 cfg 0 > port 2 pin 21 cfg 0 > port 2 pin 22 cfg 0 > port 2 pin 23 cfg 0 > port 2 pin 24 cfg 0 > gpio2 at sxipio0: 25 pins > port 3 pin 0 cfg 0 > port 3 pin 1 cfg 0 > port 3 pin 2 cfg 0 > port 3 pin 3 cfg 0 > port 3 pin 4 cfg 0 > port 3 pin 5 cfg 0 > port 3 pin 6 cfg 0 > port 3 pin 7 cfg 0 > port 3 pin 8 cfg 0 > port 3 pin 9 cfg 0 > port 3 pin 10 cfg 0 > port 3 pin 11 cfg 0 > port 3 pin 12 cfg 0 > port 3 pin 13 cfg 0 > port 3 pin 14 cfg 0 > port 3 pin 15 cfg 0 > port 3 pin 16 cfg 0 > port 3 pin 17 cfg 0 > port 3 pin 18 cfg 0 > port 3 pin 19 cfg 0 > port 3 pin 20 cfg 0 > port 3 pin 21 cfg 0 > port 3 pin 22 cfg 0 > port 3 pin 23 cfg 0 > port 3 pin 24 cfg 0 > port 3 pin 25 cfg 0 > port 3 pin 26 cfg 0 > port 3 pin 27 cfg 0 > gpio3 at sxipio0: 28 pins > port 4 pin 0 cfg 0 > port 4 pin 1 cfg 0 > port 4 pin 2 cfg 0 > port 4 pin 3 cfg 0 > port 4 pin 4 cfg 0 > port 4 pin 5 cfg 0 > port 4 pin 6 cfg 0 > port 4 pin 7 cfg 0 > port 4 pin 8 cfg 0 > port 4 pin 9 cfg 0 > port 4 pin 10 cfg 0 > port 4 pin 11 cfg 0 > gpio4 at sxipio0: 12 pins > port 5 pin 0 cfg 2 > port 5 pin 1 cfg 2 > port 5 pin 2 cfg 2 > port 5 pin 3 cfg 2 > port 5 pin 4 cfg 2 > port 5 pin 5 cfg 2 > gpio5 at sxipio0: 6 pins > port 6 pin 0 cfg 0 > port 6 pin 1 cfg 0 > port 6 pin 2 cfg 0 > port 6 pin 3 cfg 0 > port 6 pin 4 cfg 0 > port 6 pin 5 cfg 0 > port 6 pin 6 cfg 0 > port 6 pin 7 cfg 0 > port 6 pin 8 cfg 0 > port 6 pin 9 cfg 0 > port 6 pin 10 cfg 0 > port 6 pin 11 cfg 0 > gpio6 at sxipio0: 12 pins > port 7 pin 0 cfg 0 > port 7 pin 1 cfg 0 > port 7 pin 2 cfg 1 > port 7 pin 3 cfg 1 > port 7 pin 4 cfg 0 > port 7 pin 5 cfg 0 > port 7 pin 6 cfg 0 > port 7 pin 7 cfg 0 > port 7 pin 8 cfg 0 > port 7 pin 9 cfg 0 > port 7 pin 10 cfg 0 > port 7 pin 11 cfg 1 > port 7 pin 12 cfg 0 > port 7 pin 13 cfg 0 > port 7 pin 14 cfg 0 > port 7 pin 15 cfg 0 > port 7 pin 16 cfg 0 > port 7 pin 17 cfg 0 > port 7 pin 18 cfg 0 > port 7 pin 19 cfg 0 > port 7 pin 20 cfg 0 > port 7 pin 21 cfg 0 > port 7 pin 22 cfg 0 > port 7 pin 23 cfg 0 > port 7 pin 24 cfg 0 > port 7 pin 25 cfg 0 > port 7 pin 26 cfg 0 > port 7 pin 27 cfg 0 > gpio7 at sxipio0: 28 pins > port 8 pin 0 cfg 0 > port 8 pin 1 cfg 0 > port 8 pin 2 cfg 0 > port 8 pin 3 cfg 0 > port 8 pin 4 cfg 0 > port 8 pin 5 cfg 0 > port 8 pin 6 cfg 0 > port 8 pin 7 cfg 0 > port 8 pin 8 cfg 0 > port 8 pin 9 cfg 0 > port 8 pin 10 cfg 0 > port 8 pin 11 cfg 0 > port 8 pin 12 cfg 0 > port 8 pin 13 cfg 0 > port 8 pin 14 cfg 0 > port 8 pin 15 cfg 0 > port 8 pin 16 cfg 0 > port 8 pin 17 cfg 0 > port 8 pin 18 cfg 0 > port 8 pin 19 cfg 0 > port 8 pin 20 cfg 0 > port 8 pin 21 cfg 0 > gpio8 at sxipio0: 22 pins > enable irq 54 register 104 bitmask 00400000 > enable irq 55 register 104 bitmask 00800000 > Timecounters tick every 10.000 msec > XXXafter fork...before kthread_run_deferred_queue() > XXXafter kthread_run_deferred_queue() > XXXbefore dostartuphooks() > XXXafter dostartuphooks() > boot device: rd0 > dev=0x1202 chrdev=0x1202 rawdev=0x1202 > root on rd0a swap on rd0b dump on rd0b > XXXafter diskconf() > dev=0x1200 chrdev=0x1200 rawdev=0x1202 > WARNING: clock lost 2109 days > WARNING: CHECK AND RESET THE DATE! > XXXafter mountroot() > XXXbefore uvm_swap_init() > XXXbefore start_init_exec() > XXXbefore idle... > init: copying out path `/sbin/init' 11 > XXXreturned from sys_execve(). > XXXafter KERNEL_UNLOCK > > > > The XXX* lines are the printf()s. > > > Anyway, to make it work, I had to disable the usb > related drivers: > #ehci* at sunxi? # EHCI (shim) > #usb* at ehci? #flags 0x1 > > > Also, I've enabled the ddb with > option DDB > option DDB_SAFE_CONSOLE > > but even if I send BREAKs from the serial console, the > debugger isn't called. > > Any help is welcome. > > Leonardo. > > > > > On Sat, Oct 03, 2015 at 11:54:51AM +0200, Leonardo Guardati wrote: >> Hi, >> I'm back trying to make the pcDuino3_Nano board >> work with OpenBSD. >> >> The u-boot version shipped with the board: >> U-Boot 2011.09-rc1 (Jul 03 2013 - 17:40:47) Allwinner Technology >> >> Is not able to load openbsd from sd card. >> >> Back in august I wrote to the list with a config option for >> u-boot 2015-07 to make the bsd.umg image load; that >> was: >> [*] Enable workarounds for booting old kernels >> under ARM Architecture of the uboot menuconfig. >> >> Now, using the last uboot git version >> >> U-Boot 2015.10-rc3-00297-g1a9c229 (Sep 27 2015 - 11:01:54 +0200) Allwinner >> Technology >> >> it would stop at dram initialization: >> >> DRAM:Timeout initialising DRAM >> >> >> I had to change another config option to make it work: >> >> "ARM Architecture" -> "sunxi dram timings" set to "JEDEC DDR3-800E / >> DDR3-1066G / DDR3-1333J" >> >> instead of "Magic vendor timings from Android" >> >> >> Now I'm back to square one with the same problem: openbsd loads fine but >> stuck at the >> end of hardware initialization: >> >> [see output1.log] >> >> >> The sd0 (a SATA disk) device is found. >> >> I've tried to run the same bsd.umg binary in QEMU, and it has the same >> behaviour; but it spews some >> other messages after the gpio: >> >> $ qemu-system-arm -M cubieboard -kernel bsd.rd.SUNXI.umg -m 1024M >> >> [see output2.log] >> >> >> Now I compiled the bsd.rd with debug option activated: and here the >> results: >> >> [see output3.log] >> >> >> and this is without the external SATA disk: >> >> >> [see output4.log] >> >> >> I've checked the source code (I'm not able yet >> to debug live the code...any suggestion on how to >> setup that?) and adding some printf()s here and >> there I saw that the code stops on sys/kern/init_main.c@: >> >> while (config_pending) >> (void) tsleep((void *)&config_pending, PWAIT, "cfpend", 0); >> >> the threads are woken up and I see the disk_attach_callback()s for >> each of the devices (rd and sd) but then something goes wrong >> and >> >> dostartuphooks(); >> >> is never reached. >> >> I've verified the disk_attach_callback() calls the final wakeup(). >> >> Also, in the tsleep() loop, the while() tests on config_pending=2. >> >> Any hint on what could be the problem? >> It seems like the thread waiting for the deferred autoconfiguration >> doesn't wake up. >> >> >> >> >> Leonardo. >> >> >> >> > >> U-Boot SPL 2015.10-rc3-00297-g1a9c229 (Sep 27 2015 - 11:01:54) >> DRAM: 1024 MiB >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 >> >> >> U-Boot 2015.10-rc3-00297-g1a9c229 (Sep 27 2015 - 11:01:54 +0200) Allwinner >> Technology >> >> CPU: Allwinner A20 (SUN7I) >> I2C: ready >> DRAM: 1 GiB >> MMC: SUNXI SD/MMC: 0 >> *** Warning - bad CRC, using default environment >> >> In: serial >> Out: serial >> Err: serial >> SCSI: SUNXI SCSI INIT >> Target spinup took 0 ms. >> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >> flags: ncq stag pm led clo only pmp pio slum part ccc apst >> Net: eth0: ethernet@01c50000 >> starting USB... >> USB0: USB EHCI 1.00 >> USB1: USB OHCI 1.0 >> USB2: USB EHCI 1.00 >> USB3: USB OHCI 1.0 >> scanning bus 0 for devices... 1 USB Device(s) found >> scanning bus 2 for devices... 1 USB Device(s) found >> Hit any key to stop autoboot: 0 >> => fatload mmc 0 0x48000000 bsd.umg >> reading bsd.umg >> 8028428 bytes read in 452 ms (16.9 MiB/s) >> => >> => >> => bootm 0x48000000 >> ## Booting kernel from Legacy Image at 48000000 ... >> Image Name: boot >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 8028364 Bytes = 7.7 MiB >> Load Address: 40300000 >> Entry Point: 40300000 >> Verifying Checksum ... OK >> Loading Kernel Image ... OK >> >> Starting kernel ... >> >> >> OpenBSD/sunxi booting ... >> arg0 0x0 arg1 0x10bb arg2 0x40000100 >> atag core flags 0 pagesize 0 rootdev 0 >> atag serial 0x16516604:080264c0 >> atag mem start 0x40000000 size 0x40000000 >> bootfile: >> bootargs: >> memory size derived from u-boot >> bootconf.mem[0].address = 40000000 pages 262144/0x40000000 >> Allocating page tables >> freestart = 0x40aa9000, free_pages = 259415 (0x0003f557) >> IRQ stack: p0x40ad7000 v0xc0ad7000 >> ABT stack: p0x40ad8000 v0xc0ad8000 >> UND stack: p0x40ad9000 v0xc0ad9000 >> SVC stack: p0x40ada000 v0xc0ada000 >> Creating L1 page table at 0x40aac000 >> Mapping kernel >> Constructing L2 page tables >> undefined page pmap board type: 4283 >> Copyright (c) 1982, 1986, 1989, 1991, 1993 >> The Regents of the University of California. All rights reserved. >> Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org >> >> OpenBSD 5.8-current (RAMDISK) #23: Mon Sep 21 16:37:27 AEST 2015 >> j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK >> real mem = 1073741824 (1024MB) >> avail mem = 1041674240 (993MB) >> mainbus0 at root >> cortex0 at mainbus0 >> ampintc0 at cortex0 nirq 160 >> agtimer0 at cortex0: tick rate 24000 KHz >> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core) >> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled >> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache >> sunxi0 at mainbus0: Allwinner A20 >> sxipio0 at sunxi0 >> sxiccmu0 at sunxi0 >> sxitimer0 at sunxi0: ticktimer 100hz @ 32KHz >> sxitimer1 at sunxi0: stattimer 128hz @ 32KHz >> sxitimer2 at sunxi0: cntrtimer @ 32KHz >> sxidog0 at sunxi0 >> sxirtc0 at sunxi0 >> sxiuart0 at sunxi0: console >> sxiuart1 at sunxi0 >> sxiuart2 at sunxi0 >> sxiuart3 at sunxi0 >> sxiuart4 at sunxi0 >> sxiuart5 at sunxi0 >> sxiuart6 at sunxi0 >> sxiuart7 at sunxi0 >> sxie0 at sunxi0, address 02:04:08:02:64:c0 >> rgephy0 at sxie0 phy 0: RTL8169S/8110S/8211 PHY, rev. 5 >> rgephy1 at sxie0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5 >> ahci0 at sunxi0 AHCI 1.1 >> ahci0: port 0: 3.0Gb/s >> scsibus0 at ahci0: 32 targets >> sd0 at scsibus0 targ 0 lun 0: <ATA, WDC WD10JPVX-22J, 01.0> SCSI3 0/direct >> fixed naa.50014ee65ac04a9a >> sd0: 953869MB, 512 bytes/sector, 1953525168 sectors >> ehci0 at sunxi0 >> usb0 at ehci0: USB revision 2.0 >> uhub0 at usb0 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1 >> ehci1 at sunxi0 >> usb1 at ehci1: USB revision 2.0 >> uhub1 at usb1 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1 >> gpio0 at sxipio0: 18 pins >> gpio1 at sxipio0: 24 pins >> gpio2 at sxipio0: 25 pins >> gpio3 at sxipio0: 28 pins >> gpio4 at sxipio0: 12 pins >> gpio5 at sxipio0: 6 pins >> gpio6 at sxipio0: 12 pins >> gpio7 at sxipio0: 28 pins >> gpio8 at sxipio0: 22 pins >> >> > >> OpenBSD/sunxi booting ... >> arg0 0x0 arg1 0x1008 arg2 0x40000100 >> atag core flags 1 pagesize 1000 rootdev 0 >> atag mem start 0x40000000 size 0x40000000 >> bootfile: >> bootargs: >> memory size derived from u-boot >> bootconf.mem[0].address = 40000000 pages 262144/0x40000000 >> Allocating page tables >> freestart = 0x40aa9000, free_pages = 259415 (0x0003f557) >> IRQ stack: p0x40ad7000 v0xc0ad7000 >> ABT stack: p0x40ad8000 v0xc0ad8000 >> UND stack: p0x40ad9000 v0xc0ad9000 >> SVC stack: p0x40ada000 v0xc0ada000 >> Creating L1 page table at 0x40aac000 >> Mapping kernel >> Constructing L2 page tables >> undefined page pmap board type: 4104 >> Copyright (c) 1982, 1986, 1989, 1991, 1993 >> The Regents of the University of California. All rights reserved. >> Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org >> >> OpenBSD 5.8-current (RAMDISK) #23: Mon Sep 21 16:37:27 AEST 2015 >> j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK >> real mem = 1073741824 (1024MB) >> avail mem = 1041674240 (993MB) >> mainbus0 at root >> cpu0 at mainbus0: ARM Cortex A8 rev 0 (ARMv7 core) >> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled >> cpu0: 16KB(64b/l,4way) I-cache, 16KB(64b/l,4way) wr-back D-cache >> sunxi0 at mainbus0: Allwinner A1x >> sxipio0 at sunxi0 >> sxiccmu0 at sunxi0 >> a1xintc0 at sunxi0 >> sxitimer0 at sunxi0: ticktimer 100hz @ 32KHz >> sxitimer1 at sunxi0: stattimer 128hz @ 32KHz >> sxitimer2 at sunxi0: cntrtimer @ 32KHz >> sxidog0 at sunxi0 >> sxirtc0 at sunxi0 >> sxiuart0 at sunxi0: console >> sxiuart1 at sunxi0 >> sxiuart2 at sunxi0 >> sxiuart3 at sunxi0 >> sxiuart4 at sunxi0 >> sxiuart5 at sunxi0 >> sxiuart6 at sunxi0 >> sxiuart7 at sunxi0 >> sxie0 at sunxi0, address fe:e1:ba:d0:6b:f0 >> rlphy0 at sxie0 phy 1: RTL8201L 10/100 PHY, rev. 1 >> ahci0 at sunxi0: AHCI phy power up failed. >> ehci0 at sunxi0 >> ehci0: halt timeout >> usb0 at ehci0: USB revision 2.0 >> uhub0 at usb0 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1 >> uhub0: no ports, hub ignored >> usb0: root device is not a hub >> ehci1 at sunxi0 >> ehci1: halt timeout >> usb1 at ehci1: USB revision 2.0 >> uhub1 at usb1 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1 >> uhub1: no ports, hub ignored >> usb1: root device is not a hub >> gpio0 at sxipio0: 18 pins >> gpio1 at sxipio0: 24 pins >> gpio2 at sxipio0: 25 pins >> gpio3 at sxipio0: 28 pins >> gpio4 at sxipio0: 12 pins >> gpio5 at sxipio0: 6 pins >> gpio6 at sxipio0: 12 pins >> gpio7 at sxipio0: 28 pins >> gpio8 at sxipio0: 22 pins >> boot device: lookup '' failed. >> root on rd0a swap on rd0b dump on rd0b >> WARNING: preposterous clock chip time >> WARNING: CHECK AND RESET THE DATE! >> > >> U-Boot SPL 2015.10-rc3-00297-g1a9c229 (Sep 30 2015 - 21:47:24) >> DRAM: 1024 MiB >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 >> >> >> U-Boot 2015.10-rc3-00297-g1a9c229 (Sep 30 2015 - 21:47:24 +0200) Allwinner >> Technology >> >> CPU: Allwinner A20 (SUN7I) >> I2C: ready >> DRAM: 1 GiB >> MMC: SUNXI SD/MMC: 0 >> *** Warning - bad CRC, using default environment >> >> In: serial >> Out: serial >> Err: serial >> SCSI: SUNXI SCSI INIT >> Target spinup took 0 ms. >> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >> flags: ncq stag pm led clo only pmp pio slum part ccc apst >> Net: eth0: ethernet@01c50000 >> starting USB... >> USB0: USB EHCI 1.00 >> USB1: USB OHCI 1.0 >> USB2: USB EHCI 1.00 >> USB3: USB OHCI 1.0 >> scanning bus 0 for devices... 1 USB Device(s) found >> scanning bus 2 for devices... 1 USB Device(s) found >> Hit any key to stop autoboot: 0 >> => fatload mmc 0 0x40200000 bsd.umg; bootm 0x40200000 >> reading bsd.umg >> 8029540 bytes read in 407 ms (18.8 MiB/s) >> ## Booting kernel from Legacy Image at 40200000 ... >> Image Name: boot >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 8029476 Bytes = 7.7 MiB >> Load Address: 40300000 >> Entry Point: 40300000 >> Verifying Checksum ... OK >> Loading Kernel Image ... OK >> >> Starting kernel ... >> >> >> OpenBSD/sunxi booting ... >> arg0 0x0 arg1 0x10bb arg2 0x40000100 >> atag core flags 0 pagesize 0 rootdev 0 >> atag serial 0x16516604:080264c0 >> atag mem start 0x40000000 size 0x40000000 >> bootfile: >> bootargs: >> memory size derived from u-boot >> bootconf.mem[0].address = 40000000 pages 262144/0x40000000 >> physmemory: 262144 pages at 0x40000000 -> 0x7fffffff >> Allocating page tables >> freestart = 0x40aa9000, free_pages = 259415 (0x0003f557) >> IRQ stack: p0x40ad7000 v0xc0ad7000 >> ABT stack: p0x40ad8000 v0xc0ad8000 >> UND stack: p0x40ad9000 v0xc0ad9000 >> SVC stack: p0x40ada000 v0xc0ada000 >> Creating L1 page table at 0x40aac000 >> Mapping kernel >> Constructing L2 page tables >> undefined page pmap board type: 4283 >> Copyright (c) 1982, 1986, 1989, 1991, 1993 >> The Regents of the University of California. All rights reserved. >> Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org >> >> OpenBSD 5.8-current (RAMDISK) #6: Wed Sep 30 21:51:18 CEST 2015 >> r...@cc.my.domain:/usr/src/sys/arch/armv7/compile/RAMDISK >> real mem = 1073741824 (1024MB) >> avail mem = 1041674240 (993MB) >> mainbus0 at root >> cortex0 at mainbus0 >> ampintc0 at cortex0 nirq 160 >> agtimer0 at cortex0: tick rate 24000 KHz >> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core) >> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled >> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache >> sunxi0 at mainbus0: Allwinner A20 >> sxipio0 at sunxi0 >> sxiccmu0 at sunxi0 >> sxitimer0 at sunxi0: ticktimer 100hz @ 32KHz >> sxitimer1 at sunxi0: stattimer 128hz @ 32KHz >> sxitimer2 at sunxi0: cntrtimer @ 32KHz >> sxidog0 at sunxi0: ctrl 0 mode 0 >> >> sxirtc0 at sunxi0 >> sxiuart0 at sunxi0: consoleenable irq 33 register 104 bitmask 00000002 >> >> sxiuart1 at sunxi0enable irq 34 register 104 bitmask 00000004 >> >> sxiuart2 at sunxi0enable irq 35 register 104 bitmask 00000008 >> >> sxiuart3 at sunxi0enable irq 36 register 104 bitmask 00000010 >> >> sxiuart4 at sunxi0enable irq 49 register 104 bitmask 00020000 >> >> sxiuart5 at sunxi0enable irq 50 register 104 bitmask 00040000 >> >> sxiuart6 at sunxi0enable irq 51 register 104 bitmask 00080000 >> >> sxiuart7 at sunxi0enable irq 52 register 104 bitmask 00100000 >> >> sxie0 at sunxi0enable irq 87 register 108 bitmask 00800000 >> , address 02:04:08:02:64:c0 >> rgephy0 at sxie0 phy 0: RTL8169S/8110S/8211 PHY, rev. 5 >> rgephy1 at sxie0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5 >> ahci0 at sunxi0enable irq 88 register 108 bitmask 01000000 >> AHCI 1.1 >> ahci0: port 0: 3.0Gb/s >> scsibus0 at ahci0: 32 targets >> sd0 at scsibus0 targ 0 lun 0: <ATA, WDC WD10JPVX-22J, 01.0> SCSI3 0/direct >> fixed naa.50014ee65ac04a9a >> sd0: 953869MB, 512 bytes/sector, 1953525168 sectors >> ehci0 at sunxi0 >> enable irq 71 register 108 bitmask 00000080 >> usb0 at ehci0: USB revision 2.0 >> uhub0 at usb0 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1 >> ehci1 at sunxi0 >> enable irq 72 register 108 bitmask 00000100 >> usb1 at ehci1: USB revision 2.0 >> uhub1 at usb1 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1 >> port 0 pin 0 cfg 2 >> port 0 pin 1 cfg 2 >> port 0 pin 2 cfg 2 >> port 0 pin 3 cfg 2 >> port 0 pin 4 cfg 2 >> port 0 pin 5 cfg 2 >> port 0 pin 6 cfg 2 >> port 0 pin 7 cfg 2 >> port 0 pin 8 cfg 2 >> port 0 pin 9 cfg 2 >> port 0 pin 10 cfg 2 >> port 0 pin 11 cfg 2 >> port 0 pin 12 cfg 2 >> port 0 pin 13 cfg 2 >> port 0 pin 14 cfg 2 >> port 0 pin 15 cfg 2 >> port 0 pin 16 cfg 2 >> port 0 pin 17 cfg 2 >> gpio0 at sxipio0: 18 pins >> port 1 pin 0 cfg 2 >> port 1 pin 1 cfg 2 >> port 1 pin 2 cfg 0 >> port 1 pin 3 cfg 0 >> port 1 pin 4 cfg 0 >> port 1 pin 5 cfg 0 >> port 1 pin 6 cfg 0 >> port 1 pin 7 cfg 0 >> port 1 pin 8 cfg 1 >> port 1 pin 9 cfg 0 >> port 1 pin 10 cfg 0 >> port 1 pin 11 cfg 0 >> port 1 pin 12 cfg 0 >> port 1 pin 13 cfg 0 >> port 1 pin 14 cfg 0 >> port 1 pin 15 cfg 0 >> port 1 pin 16 cfg 0 >> port 1 pin 17 cfg 0 >> port 1 pin 18 cfg 0 >> port 1 pin 19 cfg 0 >> port 1 pin 20 cfg 0 >> port 1 pin 21 cfg 0 >> port 1 pin 22 cfg 2 >> port 1 pin 23 cfg 2 >> gpio1 at sxipio0: 24 pins >> port 2 pin 0 cfg 0 >> port 2 pin 1 cfg 0 >> port 2 pin 2 cfg 0 >> port 2 pin 3 cfg 0 >> port 2 pin 4 cfg 0 >> port 2 pin 5 cfg 0 >> port 2 pin 6 cfg 0 >> port 2 pin 7 cfg 0 >> port 2 pin 8 cfg 0 >> port 2 pin 9 cfg 0 >> port 2 pin 10 cfg 0 >> port 2 pin 11 cfg 0 >> port 2 pin 12 cfg 0 >> port 2 pin 13 cfg 0 >> port 2 pin 14 cfg 0 >> port 2 pin 15 cfg 0 >> port 2 pin 16 cfg 0 >> port 2 pin 17 cfg 0 >> port 2 pin 18 cfg 0 >> port 2 pin 19 cfg 0 >> port 2 pin 20 cfg 0 >> port 2 pin 21 cfg 0 >> port 2 pin 22 cfg 0 >> port 2 pin 23 cfg 0 >> port 2 pin 24 cfg 0 >> gpio2 at sxipio0: 25 pins >> port 3 pin 0 cfg 0 >> port 3 pin 1 cfg 0 >> port 3 pin 2 cfg 0 >> port 3 pin 3 cfg 0 >> port 3 pin 4 cfg 0 >> port 3 pin 5 cfg 0 >> port 3 pin 6 cfg 0 >> port 3 pin 7 cfg 0 >> port 3 pin 8 cfg 0 >> port 3 pin 9 cfg 0 >> port 3 pin 10 cfg 0 >> port 3 pin 11 cfg 0 >> port 3 pin 12 cfg 0 >> port 3 pin 13 cfg 0 >> port 3 pin 14 cfg 0 >> port 3 pin 15 cfg 0 >> port 3 pin 16 cfg 0 >> port 3 pin 17 cfg 0 >> port 3 pin 18 cfg 0 >> port 3 pin 19 cfg 0 >> port 3 pin 20 cfg 0 >> port 3 pin 21 cfg 0 >> port 3 pin 22 cfg 0 >> port 3 pin 23 cfg 0 >> port 3 pin 24 cfg 0 >> port 3 pin 25 cfg 0 >> port 3 pin 26 cfg 0 >> port 3 pin 27 cfg 0 >> gpio3 at sxipio0: 28 pins >> port 4 pin 0 cfg 0 >> port 4 pin 1 cfg 0 >> port 4 pin 2 cfg 0 >> port 4 pin 3 cfg 0 >> port 4 pin 4 cfg 0 >> port 4 pin 5 cfg 0 >> port 4 pin 6 cfg 0 >> port 4 pin 7 cfg 0 >> port 4 pin 8 cfg 0 >> port 4 pin 9 cfg 0 >> port 4 pin 10 cfg 0 >> port 4 pin 11 cfg 0 >> gpio4 at sxipio0: 12 pins >> port 5 pin 0 cfg 2 >> port 5 pin 1 cfg 2 >> port 5 pin 2 cfg 2 >> port 5 pin 3 cfg 2 >> port 5 pin 4 cfg 2 >> port 5 pin 5 cfg 2 >> gpio5 at sxipio0: 6 pins >> port 6 pin 0 cfg 0 >> port 6 pin 1 cfg 0 >> port 6 pin 2 cfg 0 >> port 6 pin 3 cfg 0 >> port 6 pin 4 cfg 0 >> port 6 pin 5 cfg 0 >> port 6 pin 6 cfg 0 >> port 6 pin 7 cfg 0 >> port 6 pin 8 cfg 0 >> port 6 pin 9 cfg 0 >> port 6 pin 10 cfg 0 >> port 6 pin 11 cfg 0 >> gpio6 at sxipio0: 12 pins >> port 7 pin 0 cfg 0 >> port 7 pin 1 cfg 0 >> port 7 pin 2 cfg 1 >> port 7 pin 3 cfg 1 >> port 7 pin 4 cfg 0 >> port 7 pin 5 cfg 0 >> port 7 pin 6 cfg 1 >> port 7 pin 7 cfg 0 >> port 7 pin 8 cfg 0 >> port 7 pin 9 cfg 0 >> port 7 pin 10 cfg 0 >> port 7 pin 11 cfg 1 >> port 7 pin 12 cfg 0 >> port 7 pin 13 cfg 0 >> port 7 pin 14 cfg 0 >> port 7 pin 15 cfg 0 >> port 7 pin 16 cfg 0 >> port 7 pin 17 cfg 0 >> port 7 pin 18 cfg 0 >> port 7 pin 19 cfg 0 >> port 7 pin 20 cfg 0 >> port 7 pin 21 cfg 0 >> port 7 pin 22 cfg 0 >> port 7 pin 23 cfg 0 >> port 7 pin 24 cfg 0 >> port 7 pin 25 cfg 0 >> port 7 pin 26 cfg 0 >> port 7 pin 27 cfg 0 >> gpio7 at sxipio0: 28 pins >> port 8 pin 0 cfg 0 >> port 8 pin 1 cfg 0 >> port 8 pin 2 cfg 0 >> port 8 pin 3 cfg 0 >> port 8 pin 4 cfg 0 >> port 8 pin 5 cfg 0 >> port 8 pin 6 cfg 0 >> port 8 pin 7 cfg 0 >> port 8 pin 8 cfg 0 >> port 8 pin 9 cfg 0 >> port 8 pin 10 cfg 0 >> port 8 pin 11 cfg 0 >> port 8 pin 12 cfg 0 >> port 8 pin 13 cfg 0 >> port 8 pin 14 cfg 0 >> port 8 pin 15 cfg 0 >> port 8 pin 16 cfg 0 >> port 8 pin 17 cfg 0 >> port 8 pin 18 cfg 0 >> port 8 pin 19 cfg 0 >> port 8 pin 20 cfg 0 >> port 8 pin 21 cfg 0 >> gpio8 at sxipio0: 22 pins >> enable irq 54 register 104 bitmask 00400000 >> enable irq 55 register 104 bitmask 00800000 >> Timecounters tick every 10.000 msec >> dev=0x1802 chrdev=0x1802 rawdev=0x1802 >> dev=0x1202 chrdev=0x1202 rawdev=0x1202 >> > >> U-Boot SPL 2015.10-rc3-00297-g1a9c229 (Sep 30 2015 - 21:47:24) >> DRAM: 1024 MiB >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 >> >> >> U-Boot 2015.10-rc3-00297-g1a9c229 (Sep 30 2015 - 21:47:24 +0200) Allwinner >> Technology >> >> CPU: Allwinner A20 (SUN7I) >> I2C: ready >> DRAM: 1 GiB >> MMC: SUNXI SD/MMC: 0 >> *** Warning - bad CRC, using default environment >> >> In: serial >> Out: serial >> Err: serial >> SCSI: SUNXI SCSI INIT >> SATA link 0 timeout. >> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode >> flags: ncq stag pm led clo only pmp pio slum part ccc apst >> Net: eth0: ethernet@01c50000 >> starting USB... >> USB0: USB EHCI 1.00 >> USB1: USB OHCI 1.0 >> USB2: USB EHCI 1.00 >> USB3: USB OHCI 1.0 >> scanning bus 0 for devices... 1 USB Device(s) found >> scanning bus 2 for devices... 1 USB Device(s) found >> Hit any key to stop autoboot: 0 >> => fatload mmc 0 0x40200000 bsd.umg; bootm 0x40200000 >> reading bsd.umg >> 8029540 bytes read in 407 ms (18.8 MiB/s) >> ## Booting kernel from Legacy Image at 40200000 ... >> Image Name: boot >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 8029476 Bytes = 7.7 MiB >> Load Address: 40300000 >> Entry Point: 40300000 >> Verifying Checksum ... OK >> Loading Kernel Image ... OK >> >> Starting kernel ... >> >> >> OpenBSD/sunxi booting ... >> arg0 0x0 arg1 0x10bb arg2 0x40000100 >> atag core flags 0 pagesize 0 rootdev 0 >> atag serial 0x16516604:080264c0 >> atag mem start 0x40000000 size 0x40000000 >> bootfile: >> bootargs: >> memory size derived from u-boot >> bootconf.mem[0].address = 40000000 pages 262144/0x40000000 >> physmemory: 262144 pages at 0x40000000 -> 0x7fffffff >> Allocating page tables >> freestart = 0x40aa9000, free_pages = 259415 (0x0003f557) >> IRQ stack: p0x40ad7000 v0xc0ad7000 >> ABT stack: p0x40ad8000 v0xc0ad8000 >> UND stack: p0x40ad9000 v0xc0ad9000 >> SVC stack: p0x40ada000 v0xc0ada000 >> Creating L1 page table at 0x40aac000 >> Mapping kernel >> Constructing L2 page tables >> undefined page pmap board type: 4283 >> Copyright (c) 1982, 1986, 1989, 1991, 1993 >> The Regents of the University of California. All rights reserved. >> Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org >> >> OpenBSD 5.8-current (RAMDISK) #6: Wed Sep 30 21:51:18 CEST 2015 >> r...@cc.my.domain:/usr/src/sys/arch/armv7/compile/RAMDISK >> real mem = 1073741824 (1024MB) >> avail mem = 1041674240 (993MB) >> mainbus0 at root >> cortex0 at mainbus0 >> ampintc0 at cortex0 nirq 160 >> agtimer0 at cortex0: tick rate 24000 KHz >> cpu0 at mainbus0: ARM Cortex A7 rev 4 (ARMv7 core) >> cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled >> cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache >> sunxi0 at mainbus0: Allwinner A20 >> sxipio0 at sunxi0 >> sxiccmu0 at sunxi0 >> sxitimer0 at sunxi0: ticktimer 100hz @ 32KHz >> sxitimer1 at sunxi0: stattimer 128hz @ 32KHz >> sxitimer2 at sunxi0: cntrtimer @ 32KHz >> sxidog0 at sunxi0: ctrl 0 mode 0 >> >> sxirtc0 at sunxi0 >> sxiuart0 at sunxi0: consoleenable irq 33 register 104 bitmask 00000002 >> >> sxiuart1 at sunxi0enable irq 34 register 104 bitmask 00000004 >> >> sxiuart2 at sunxi0enable irq 35 register 104 bitmask 00000008 >> >> sxiuart3 at sunxi0enable irq 36 register 104 bitmask 00000010 >> >> sxiuart4 at sunxi0enable irq 49 register 104 bitmask 00020000 >> >> sxiuart5 at sunxi0enable irq 50 register 104 bitmask 00040000 >> >> sxiuart6 at sunxi0enable irq 51 register 104 bitmask 00080000 >> >> sxiuart7 at sunxi0enable irq 52 register 104 bitmask 00100000 >> >> sxie0 at sunxi0enable irq 87 register 108 bitmask 00800000 >> , address 02:04:08:02:64:c0 >> rgephy0 at sxie0 phy 0: RTL8169S/8110S/8211 PHY, rev. 5 >> rgephy1 at sxie0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5 >> ahci0 at sunxi0enable irq 88 register 108 bitmask 01000000 >> AHCI 1.1 >> scsibus0 at ahci0: 32 targets >> ehci0 at sunxi0 >> enable irq 71 register 108 bitmask 00000080 >> usb0 at ehci0: USB revision 2.0 >> uhub0 at usb0 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1 >> ehci1 at sunxi0 >> enable irq 72 register 108 bitmask 00000100 >> usb1 at ehci1: USB revision 2.0 >> uhub1 at usb1 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1 >> port 0 pin 0 cfg 2 >> port 0 pin 1 cfg 2 >> port 0 pin 2 cfg 2 >> port 0 pin 3 cfg 2 >> port 0 pin 4 cfg 2 >> port 0 pin 5 cfg 2 >> port 0 pin 6 cfg 2 >> port 0 pin 7 cfg 2 >> port 0 pin 8 cfg 2 >> port 0 pin 9 cfg 2 >> port 0 pin 10 cfg 2 >> port 0 pin 11 cfg 2 >> port 0 pin 12 cfg 2 >> port 0 pin 13 cfg 2 >> port 0 pin 14 cfg 2 >> port 0 pin 15 cfg 2 >> port 0 pin 16 cfg 2 >> port 0 pin 17 cfg 2 >> gpio0 at sxipio0: 18 pins >> port 1 pin 0 cfg 2 >> port 1 pin 1 cfg 2 >> port 1 pin 2 cfg 0 >> port 1 pin 3 cfg 0 >> port 1 pin 4 cfg 0 >> port 1 pin 5 cfg 0 >> port 1 pin 6 cfg 0 >> port 1 pin 7 cfg 0 >> port 1 pin 8 cfg 1 >> port 1 pin 9 cfg 0 >> port 1 pin 10 cfg 0 >> port 1 pin 11 cfg 0 >> port 1 pin 12 cfg 0 >> port 1 pin 13 cfg 0 >> port 1 pin 14 cfg 0 >> port 1 pin 15 cfg 0 >> port 1 pin 16 cfg 0 >> port 1 pin 17 cfg 0 >> port 1 pin 18 cfg 0 >> port 1 pin 19 cfg 0 >> port 1 pin 20 cfg 0 >> port 1 pin 21 cfg 0 >> port 1 pin 22 cfg 2 >> port 1 pin 23 cfg 2 >> gpio1 at sxipio0: 24 pins >> port 2 pin 0 cfg 0 >> port 2 pin 1 cfg 0 >> port 2 pin 2 cfg 0 >> port 2 pin 3 cfg 0 >> port 2 pin 4 cfg 0 >> port 2 pin 5 cfg 0 >> port 2 pin 6 cfg 0 >> port 2 pin 7 cfg 0 >> port 2 pin 8 cfg 0 >> port 2 pin 9 cfg 0 >> port 2 pin 10 cfg 0 >> port 2 pin 11 cfg 0 >> port 2 pin 12 cfg 0 >> port 2 pin 13 cfg 0 >> port 2 pin 14 cfg 0 >> port 2 pin 15 cfg 0 >> port 2 pin 16 cfg 0 >> port 2 pin 17 cfg 0 >> port 2 pin 18 cfg 0 >> port 2 pin 19 cfg 0 >> port 2 pin 20 cfg 0 >> port 2 pin 21 cfg 0 >> port 2 pin 22 cfg 0 >> port 2 pin 23 cfg 0 >> port 2 pin 24 cfg 0 >> gpio2 at sxipio0: 25 pins >> port 3 pin 0 cfg 0 >> port 3 pin 1 cfg 0 >> port 3 pin 2 cfg 0 >> port 3 pin 3 cfg 0 >> port 3 pin 4 cfg 0 >> port 3 pin 5 cfg 0 >> port 3 pin 6 cfg 0 >> port 3 pin 7 cfg 0 >> port 3 pin 8 cfg 0 >> port 3 pin 9 cfg 0 >> port 3 pin 10 cfg 0 >> port 3 pin 11 cfg 0 >> port 3 pin 12 cfg 0 >> port 3 pin 13 cfg 0 >> port 3 pin 14 cfg 0 >> port 3 pin 15 cfg 0 >> port 3 pin 16 cfg 0 >> port 3 pin 17 cfg 0 >> port 3 pin 18 cfg 0 >> port 3 pin 19 cfg 0 >> port 3 pin 20 cfg 0 >> port 3 pin 21 cfg 0 >> port 3 pin 22 cfg 0 >> port 3 pin 23 cfg 0 >> port 3 pin 24 cfg 0 >> port 3 pin 25 cfg 0 >> port 3 pin 26 cfg 0 >> port 3 pin 27 cfg 0 >> gpio3 at sxipio0: 28 pins >> port 4 pin 0 cfg 0 >> port 4 pin 1 cfg 0 >> port 4 pin 2 cfg 0 >> port 4 pin 3 cfg 0 >> port 4 pin 4 cfg 0 >> port 4 pin 5 cfg 0 >> port 4 pin 6 cfg 0 >> port 4 pin 7 cfg 0 >> port 4 pin 8 cfg 0 >> port 4 pin 9 cfg 0 >> port 4 pin 10 cfg 0 >> port 4 pin 11 cfg 0 >> gpio4 at sxipio0: 12 pins >> port 5 pin 0 cfg 2 >> port 5 pin 1 cfg 2 >> port 5 pin 2 cfg 2 >> port 5 pin 3 cfg 2 >> port 5 pin 4 cfg 2 >> port 5 pin 5 cfg 2 >> gpio5 at sxipio0: 6 pins >> port 6 pin 0 cfg 0 >> port 6 pin 1 cfg 0 >> port 6 pin 2 cfg 0 >> port 6 pin 3 cfg 0 >> port 6 pin 4 cfg 0 >> port 6 pin 5 cfg 0 >> port 6 pin 6 cfg 0 >> port 6 pin 7 cfg 0 >> port 6 pin 8 cfg 0 >> port 6 pin 9 cfg 0 >> port 6 pin 10 cfg 0 >> port 6 pin 11 cfg 0 >> gpio6 at sxipio0: 12 pins >> port 7 pin 0 cfg 0 >> port 7 pin 1 cfg 0 >> port 7 pin 2 cfg 1 >> port 7 pin 3 cfg 1 >> port 7 pin 4 cfg 0 >> port 7 pin 5 cfg 0 >> port 7 pin 6 cfg 1 >> port 7 pin 7 cfg 0 >> port 7 pin 8 cfg 0 >> port 7 pin 9 cfg 0 >> port 7 pin 10 cfg 0 >> port 7 pin 11 cfg 1 >> port 7 pin 12 cfg 0 >> port 7 pin 13 cfg 0 >> port 7 pin 14 cfg 0 >> port 7 pin 15 cfg 0 >> port 7 pin 16 cfg 0 >> port 7 pin 17 cfg 0 >> port 7 pin 18 cfg 0 >> port 7 pin 19 cfg 0 >> port 7 pin 20 cfg 0 >> port 7 pin 21 cfg 0 >> port 7 pin 22 cfg 0 >> port 7 pin 23 cfg 0 >> port 7 pin 24 cfg 0 >> port 7 pin 25 cfg 0 >> port 7 pin 26 cfg 0 >> port 7 pin 27 cfg 0 >> gpio7 at sxipio0: 28 pins >> port 8 pin 0 cfg 0 >> port 8 pin 1 cfg 0 >> port 8 pin 2 cfg 0 >> port 8 pin 3 cfg 0 >> port 8 pin 4 cfg 0 >> port 8 pin 5 cfg 0 >> port 8 pin 6 cfg 0 >> port 8 pin 7 cfg 0 >> port 8 pin 8 cfg 0 >> port 8 pin 9 cfg 0 >> port 8 pin 10 cfg 0 >> port 8 pin 11 cfg 0 >> port 8 pin 12 cfg 0 >> port 8 pin 13 cfg 0 >> port 8 pin 14 cfg 0 >> port 8 pin 15 cfg 0 >> port 8 pin 16 cfg 0 >> port 8 pin 17 cfg 0 >> port 8 pin 18 cfg 0 >> port 8 pin 19 cfg 0 >> port 8 pin 20 cfg 0 >> port 8 pin 21 cfg 0 >> gpio8 at sxipio0: 22 pins >> enable irq 54 register 104 bitmask 00400000 >> enable irq 55 register 104 bitmask 00800000 >> Timecounters tick every 10.000 msec >> dev=0x1202 chrdev=0x1202 rawdev=0x1202
