Whoops, I must be very very tired. I worked a but on the CubieBoard and misread it.
Yeah, it’s a Cubox, so it’s i.MX. My fault. :( > Am 23.12.2014 um 22:25 schrieb Brian Conway <bcon...@rcesoftware.com>: > > Interesting, even though it's an i.MX6 SoC and not an Allwinner? > Thanks for the tip, I'll give it a look. > > Brian Conway > Founder, Owner > RCE Software, LLC > > > On Tue, Dec 23, 2014 at 3:22 PM, Patrick Wildt <m...@patrick-wildt.de> wrote: >> The i.MX version is definitely the wrong one. You gotta try the SUNXI >> version. >> >> \Patrick >> >>> Am 23.12.2014 um 21:43 schrieb Brian Conway <bcon...@rcesoftware.com>: >>> >>> Obviously not supported hardware, but wanted to throw this out in case >>> it's of use to anyone. I picked up the mid-level CuBox-i2eX >>> (dual-core, serial over USB, >>> http://www.solid-run.com/products/cubox-i-mini-computer/cubox-i-specifications/) >>> model and attempted to load the 12/14/2014 IMX snapshot (via tftp >>> using SolidRun's Ignition image as the U-Boot source). Logs are below, >>> let me know if there's any assistance I can in the future. Thanks. >>> >>> U-Boot SPL 2013.10-rc4 (Oct 27 2014 - 18:17:31) >>> Boot Device: SD1 >>> spl: error reading image u-boot.img, err - -1 >>> Load image from RAW... >>> >>> >>> U-Boot 2013.10-rc4 (Oct 27 2014 - 18:17:31) >>> >>> CPU: Freescale i.MX6Q rev1.5 at 792 MHz >>> Reset cause: WDOG >>> Board: MX6-CuBox-i >>> DRAM: 1 GiB >>> MMC: FSL_SDHC: 0 >>> *** Warning - bad CRC, using default environment >>> >>> In: serial >>> Out: vga >>> Err: vga >>> Net: FEC [PRIME] >>> (Re)start USB... >>> USB0: USB EHCI 1.00 >>> scanning bus 0 for devices... 1 USB Device(s) found >>> scanning usb for storage devices... 0 Storage Device(s) found >>> scanning usb for ethernet devices... 0 Ethernet Device(s) found >>> Hit any key to stop autoboot: 0 >>> CuBox-i U-Boot > dhcp >>> BOOTP broadcast 1 >>> DHCP client bound to address 10.X.Y.113 >>> Using FEC device >>> TFTP from server 10.X.Y.1; our IP address is 10.X.Y.113 >>> Filename 'pxelinux.0'. >>> Load address: 0x10800000 >>> Loading: #### >>> 1.2 MiB/s >>> done >>> Bytes transferred = 46909 (b73d hex) >>> CuBox-i U-Boot > tftpboot ${loadaddr} openbsd/bsd.rd.IMX.umg >>> Using FEC device >>> TFTP from server 10.X.Y.1; our IP address is 10.X.Y.113 >>> Filename 'openbsd/bsd.rd.IMX.umg'. >>> Load address: 0x10800000 >>> Loading: ################################################################# >>> ################################################################# >>> ################################################################# >>> ################################################################# >>> ################################################################# >>> ################################################################# >>> ################################################################# >>> ###################################################### >>> 1.4 MiB/s >>> done >>> Bytes transferred = 7461152 (71d920 hex) >>> CuBox-i U-Boot > bootm >>> ## Booting kernel from Legacy Image at 10800000 ... >>> Image Name: boot >>> Image Type: ARM Linux Kernel Image (uncompressed) >>> Data Size: 7461088 Bytes = 7.1 MiB >>> Load Address: 10800000 >>> Entry Point: 10800000 >>> Verifying Checksum ... OK >>> XIP Kernel Image ... OK >>> >>> Starting kernel ... >>> >>> undefined instruction >>> pc : [<10800008>] lr : [<4ff723b9>] >>> sp : 4f770d70 ip : 0000001e fp : 00000000 >>> r10: 00000000 r9 : 4f770f38 r8 : 4ff724e9 >>> r7 : 00000000 r6 : 10800000 r5 : 4ffa1c6c r4 : 00000000 >>> r3 : 4f770fe0 r2 : 10000100 r1 : 000012d5 r0 : 4f770fe0 >>> Flags: nZCv IRQs off FIQs off Mode SVC_32 >>> Resetting CPU ... >>> >>> resetting ... >>> >>> Brian Conway >>> >>
