Dear all, I just installed the latest armv7 snapshot onto the internal flash of a BeableBone Black. Thank you tedu@ http://www.tedunangst.com/flak/post/OpenBSD-on-BeagleBone-Black See dmesg below; from the internal flash, it runs just fine.
The reason I am installing onto the internal flash at all is that I can't install on a separate microSD card: I am *always* getting i/o errors that make the install fail. Having from a miniroot-am335x-55.fs card, the install starts fine, but after doing the disklabel, it starts reporting IO errors, similar to http://marc.info/?l=openbsd-arm&m=138619564917603&w=2 Patrick said it is an issue that got fixed http://marc.info/?l=openbsd-arm&m=138619642616977&w=2 but could I still be getting that? I suspected the card of course, but this happens with three different cards. I also suspected the BBB itself, when this was happening a month ago, so I got me a new one. The install to the microSD card seems to go better if I let the automatic label untouched, but that only fails due to IO later, when untarring the sets. Jan OpenBSD 5.5-beta (GENERIC-OMAP) #2: Wed Feb 5 21:19:22 EST 2014 r...@bbb1.openbsd.org:/usr/src/sys/arch/armv7/compile/GENERIC-OMAP real mem = 536870912 (512MB) avail mem = 518811648 (494MB) warning: no entropy supplied by boot loader mainbus0 at root cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core) cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache omap0 at mainbus0: BeagleBone prcm0 at omap0 rev 0.2 sitaracm0 at omap0: control module, rev 1.0 intc0 at omap0 rev 5.0 edma0 at omap0 rev 0.0 dmtimer0 at omap0 rev 3.1 dmtimer1 at omap0 rev 3.1 omdog0 at omap0 rev 0.1 omgpio0 at omap0: rev 0.1 gpio0 at omgpio0: 32 pins omgpio1 at omap0: rev 0.1 gpio1 at omgpio1: 32 pins omgpio2 at omap0: rev 0.1 gpio2 at omgpio2: 32 pins omgpio3 at omap0: rev 0.1 gpio3 at omgpio3: 32 pins ommmc0 at omap0 sdmmc0 at ommmc0 ommmc1 at omap0 sdmmc1 at ommmc1 com0 at omap0: ti16750, 64 byte fifo com0: console cpsw0 at omap0: version 1.12 (0), address 90:59:af:82:2e:7e ukphy0 at cpsw0 phy 0: Generic IEEE 802.3u media interface, rev. 1: OUI 0x0001f0, model 0x000f scsibus0 at sdmmc1: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <SD/MMC, Drive #01, > SCSI2 0/direct fixed sd0: 1832MB, 512 bytes/sector, 3751936 sectors vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets boot device: sd0 root on sd0a (62d40e725c6b886a.a) swap on sd0b dump on sd0b WARNING: CHECK AND RESET THE DATE!
