[Alsa-user] no digital out SPDIF port??

[Josh Sharpe]

I've managed to now get analog signal (I think) coming out my optical port.  My receiver shows the # of channels it has detected.  When I kaffeine dvd:/ I get two channels even after ensuring through the DVD menus that 5.1 is enabled.  aplay file.mp3 plays fine, however aplay test.ac3 plays static (I'm not 100% sure the file is good though since I've never been able to listen to it)  If I plug an optical cable from a DVD player into the same port on my receiver it shows 5.1 channels -- so it's not the receiver.

Here's my .asoundrc that I got from a ALSA howto.  With this one I managed to get analog working
 through the digital port.  Any ideas on this?  Thanx!

# Override the default output used by ALSA.
# If you do not override the default, your default
# device is identical to the (unmixed) analog device
# shown below. If you prefer mixed and/or digital
# output, uncomment the appropriate four lines below
# (only one slave.pcm line).
#pcm.!default {
# type plug
## Uncomment the following to use mixed analog by default
#slave.pcm "dmix-analog"
## Uncomment the following to use unmixed digital by default
# slave.pcm "digital-hw"
## Uncomment the following to use mixed digital by default
 slave.pcm "dmix-digital"
#}

# Alias for analog output on the nForce2 (hw:0,0)
# - This is identical to the device named "default"--which
# always exists and refers to hw:0,0 (unless overridden)
# - Therefore, we can specify "hw:0,0", "default", or "analog"
# to access analog output on the nForce2
pcm.analog {
type plug
slave.pcm "analog-hw"
}

# Control device (mixer, etc.) for the nForce2 card
ctl.analog {
type hw
card 0
}

# Alias for (rate-converted) mixed analog output on the
# nForce2 (hw:0,0)
# - This will accept audio input--regardless of rate--and
# convert to the rate required for the dmix plugin
# (in this case 48000Hz)
pcm.mixed-analog {
type plug
slave.pcm "dmix-analog"
}

# Control device (mixer, etc.) for the nForce2 card
ctl.mixed-analog {
type hw
card 0
}

# Alias for (rate-converted) digital (S/PDIF) output on the
# nForce2 (hw:0,2)
# - This will accept audio input--regardless of rate--and
# convert to the rate required for the S/PDIF hardware
# (in this case 48000Hz)
pcm.digital {
type plug
slave.pcm "digital-hw"
}

# Control device (mixer, etc.) for the nForce2 card
ctl.digital {
type hw
card 0
}

# Alias for mixed (rate-converted) digital (S/PDIF) output on the
# nForce2 (hw:0,2)
# - This will accept audio input--regardless of rate--and
# convert to the rate required for the S/PDIF hardware
# (in this case 48000Hz)
pcm.mixed-digital {
type plug
slave.pcm "dmix-digital"
}

# Control device (mixer, etc.) for the nForce2 card
ctl.mixed-digital {
type hw
card 0
}

# The following devices are not useful by themselves. They
# require specific rates, channels, and formats. Therefore,
# you probably do not want to use them directly. Instead use
# of of the devices defined above.

# Alias for analog output on the nForce2 (hw:0,0)
# Do not use this directly--it requires specific rate,
# channels, and format
pcm.analog-hw {
type hw
card 0
# The default value for device is 0, so no need to specify
}

# Control device (mixer, etc.) for the nForce2 card
ctl.analog-hw {
type hw
card 0
}

# Alias for digital (S/PDIF) output on the nForce2 (hw:0,2)
# Do not use this directly--it requires specific rate,
# channels, and format
pcm.digital-hw {
type hw
card 0
device 2
}

# Control device (mixer, etc.) for the nForce2 card
ctl.digital-hw {
type hw
card 0
}

# Direct software mixing plugin for analog output on
# the nForce2 (hw:0,0)
# Do not use this directly--it requires specific rate,
# channels, and format
pcm.dmix-analog {
type dmix
ipc_key 1234
slave {
pcm "analog-hw"
period_time 0
period_size 1024
buffer_size 4096
rate 48000
}
}

# Control device (mixer, etc.) for the nForce2 card
ctl.dmix-analog {
type hw
card 0
}

# Direct software mixing plugin for digital (S/PDIF) output
# on the nForce2 (hw:0,2)
# Do not use this directly--it requires specific rate,
# channels, and format
pcm.dmix-digital {
type dmix
ipc_key 1235
slave {
pcm "digital-hw"
period_time 0
period_size 1024
buffer_size 4096
rate 48000
}
}

# Control device (mixer, etc.) for the nForce2 card
ctl.dmix-digital {
type hw
card 0
}

_______________________________________________
Alsa-user mailing list
Alsa-user@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/alsa-user