I was able to get to it over the fiber too on the bench. It's like they
were bridged in recovery mode.
On 4/22/2021 11:55 AM, Josh Luthman wrote:
Yes if you put it in recovery mode it's only the cat5 cable (default
OOB config).
Josh Luthman
24/7 Help Desk: 937-552-2340
Direct: 937-552-2343
1100 Wayne St
Suite 1337
Troy, OH 45373
On Thu, Apr 22, 2021 at 12:37 PM Nate Burke <n...@blastcomm.com
<mailto:n...@blastcomm.com>> wrote:
Ok, that makes me feel a little better
Recovery mode appears to be available on both the Fiber and Cat5
From there you can enter 'default mode' which will set the data
path to the Cat5, and you can update and reboot from there.
On 4/22/2021 11:18 AM, Adam Moffett wrote:
Is Cat5 the default setting? So in recovery console mode you'd
have the Cat5 and you could get in on 169.254.1.1?
https://community.cambiumnetworks.com/t/how-to-enter-default-mode-or-recovery-console-for-450b-450i-and-450m-series-products/44936
On 4/22/2021 12:14 PM, Nate Burke wrote:
Not that I've found. It's a single drop down box to select the
data path, that's the only setting. I set it for Fiber, the
Cat5 port still has a physical link, but passes no traffic.
I unplugged the Fiber cable, plugged my laptop into the cat5 and
rebooted. I got a handfull of pings through, (maybe 5 or 6)
during the bootup process, then it stopped responding
completely. I thought maybe if it had no Link during a boot it
would automatically switch to the interface with an active link,
but no.
On 4/22/2021 11:10 AM, Adam Moffett wrote:
I don't have a 450m....
Can you have both ports on with different IP's? Even if they're
not bridged at least a way to back door in through the second port?
On 4/22/2021 12:07 PM, Nate Burke wrote:
Oh, that's bad. A fully functional AP, hanging in the air,
that's completely unusable just because what should/can be
redundant, isn't, because of software.
On 4/22/2021 10:58 AM, Josh Luthman wrote:
It sucks. That's how it is.
If it's 5 GHz you can do it over RF. If it's 3 GHz you can't
because it'll have to reach a SAS to transmit.
Josh Luthman
24/7 Help Desk: 937-552-2340
Direct: 937-552-2343
1100 Wayne St
Suite 1337
Troy, OH 45373
On Thu, Apr 22, 2021 at 11:14 AM Nate Burke
<n...@blastcomm.com <mailto:n...@blastcomm.com>> wrote:
I'm getting ready to deploy my first set of 450M radios,
from my bench
testing, and reading through the manual, do you have to
Choose which
data path is active, Copper OR Fiber? And the only way
to switch it if
that path is down is to log into the Radio with an SM
connection over
the RF? That can't be right can it?
The EPMP radios bridge the copper and Fiber inside the
radio so both are
active. That doesn't seem to be the case with the 450M.
Does the 450M
only allow one data path, and if it breaks your SOL
unless you can gain
sudo-physical access to the AP? I have be missing where
you set the
primary/secondary data path, but I haven't been able to
find it yet.
--
AF mailing list
AF@af.afmug.com <mailto:AF@af.afmug.com>
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
--
AF mailing list
AF@af.afmug.com <mailto:AF@af.afmug.com>
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
--
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
