So the thing to remember is that you can bond and balance all outgoing traffic however there’s not a whole lot you can do to dictate how traffic comes inbound to you. BGP can help but there’s not much you can do to determine routes too you.
Unless of course you have full control over both links, which it sounds like you don’t since they are from 2 different providers. -Sean On Tue, Mar 12, 2019 at 2:16 PM Mark - Myakka Technologies <m...@mailmt.com> wrote: > Josh, > > Yes. I was describing the winbox setup. Not sure if you can do > 1.1.1.1,2.2.2.2 in winbox or if you have to pull down to get another > gateway box. > -- > Best regards, > Mark mailto:m...@mailmt.com <m...@mailmt.com> > > Myakka Technologies, Inc. > www.MyakkaTech.com > > ------ > > > Tuesday, March 12, 2019, 4:04:56 PM, you wrote: > > > I think what you're saying is your dst-address=0.0.0.0/0 > gateway=1.1.1.1,2.2.2.2 > > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > <https://maps.google.com/?q=1100+Wayne+St+%0D%0ASuite+1337+%0D%0ATroy,+OH+45373&entry=gmail&source=g> > Suite 1337 > <https://maps.google.com/?q=1100+Wayne+St+%0D%0ASuite+1337+%0D%0ATroy,+OH+45373&entry=gmail&source=g> > Troy, OH 45373 > <https://maps.google.com/?q=1100+Wayne+St+%0D%0ASuite+1337+%0D%0ATroy,+OH+45373&entry=gmail&source=g> > > On Tue, Mar 12, 2019 at 1:51 PM Mark - Myakka Technologies < > m...@mailmt.com> wrote: > > Timothy, > > Been a long time since I've done something like this, being we are using > BGP now. But, back in the old startup days we were in the same situation. > > Here is something to try. > > On the router with the 2 connections, setup your default gateway 0.0.0.0/0. > In the gateway field, put in the fiber gateway. To the right you'll see an > up and down arrow. If you click on that it will allow you to put in a > second gateway. > > The tik will now use both gateways. I believe if you put the fiber > gateway in twice and the wireless gateway in once, you may get a 2 to 1 > ratio. This will only work if you are using private IP addresses to the > customers and NATing at the router. > > If you are using any public IP addresses you'll have to put some routing > rules in to force it to go out the correct interface all the time. > > As I said, been a while, so I may have missed something. I'm sure there > is better information on a WIKI somewhere. > > > > -- > Best regards, > Mark mailto:m...@mailmt.com <m...@mailmt.com> > > Myakka Technologies, Inc. > www.MyakkaTech.com > > ------ > > Tuesday, March 12, 2019, 12:37:32 PM, you wrote: > > > asking this for a buddy in the Philippines that has basically no income so > linkteks not really an option and Mikrotik forum does not seem to like me.. > > He has 2 internet connections 1 from fiber and has a Public IP > the other is from a WISP providing a dedicated BH but has a private IP > address for him to use for the WAN > > is there any way to Bond the 2 connections in Mikrotik? > > the how-to guides I have been reading do not seem to work > > > Thanks for any help -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com > -- > AF mailing list > AF@af.afmug.com > http://af.afmug.com/mailman/listinfo/af_af.afmug.com >
-- AF mailing list AF@af.afmug.com http://af.afmug.com/mailman/listinfo/af_af.afmug.com
