I took that microSD card that has the bootable image without USB and put it into a traditional Pi4. It boots on that without a problem and has mouse and keyboard. I notices that after the additional CPU cores are detected, that is mentions usb/hub… usb/kbd…. The image when booting on the Pi 400 never provides those messages.
Regards, Mack > On Jan 15, 2021, at 1:44 PM, Mack Wallace <mac...@mapinternet.com> wrote: > > Dear Skip, > > That pushed the ball forward significantly, but I still have issues. (But > thank you, every little advancement helps.) So with that flag, I was able to > get Richard’s port to boot into Glenda’s account (showing acme, faces, stats, > etc). However, I do not seem to have any USB; no mouse; nor keyboard. Stats > is moving on the screen, so things are not too locked up. I did try rebooting > with an external keyboard and another mouse. Still nothing. The external > keyboard doesn’t respond to anything (no caps lock nor num lock.) One mouse > is in the USB 2.0 port, another and the external keyboard are in the USB 3.0 > ports. > > on boot, I see the following: > usbxhci: 0x1106 0x3483 port 600000000 size 0x1000 irq0 > #u/usb/ep1.0: xhci port 0x0 irq 0 > > The line before is #l for the network, > The line after is the detection of the other three cores. > > The changing of the enable_gic=1 on the 9front image seemed to have to effect. > > Thanks again! > > Mack > > > On Jan 14, 2021, at 8:15 PM, Skip Tavakkolian <skip.tavakkol...@gmail.com > <mailto:skip.tavakkol...@gmail.com>> wrote: >> >> I'm using a RPi400 with Richard's port. I'm netbooting without issues and up >> for days. The only issue I had was forgetting to set 'enable_gic=1' as >> Richard instructed in the sources. Pi4 works ok without it, pi400 doesn't. >> >> >> On Thu, Jan 14, 2021, 3:39 PM Mack Wallace <mac...@mapinternet.com >> <mailto:mac...@mapinternet.com>> wrote: >> Thank you for the reply Stuart, but no luck. >> >> I did download Mr. Miller’s image. It would not boot at all until I replaced >> the files that you mention, but the kernel in that image locks up after >> detecting the fourth core of the CPU. However, from that failure I learned >> that those files, (start_cd.elf, start4cd.elf, fixup_cd.dat, fixup4cd.dat) >> are necessary for the Pi to boot, and that those with the bootcode.bin and >> presumably, but it doesn’t seem to matter whether I use bcm2711-rpi-4-b.dtb >> or bcm2711-rpi-400.dtb - the dtbs are vital to the process. - and that all >> those files simply need to be copied into the fat partition/boot directory. >> >> So I burned another image (actually many, trying different SD cards, and >> different configurations, older kernels, etc) and replaced all the files >> I’ve mentioned with the ones from >> https://github.com/raspberrypi/firmware/tree/master/boot >> <https://github.com/raspberrypi/firmware/tree/master/boot> (hopefully that’s >> where I should get them). My most recent iteration just has the single error >> repeated: >> >> sdhc: read error intr 2008002 stat 1fff0000 >> >> This occurs many times. In the middle of these errors is >> >> /dev/sdM0: BCM SD Host Controller 02 Version 10 >> >> then the error repeats itself over 50 times before printing out the lines >> /dev/sdM0/data >> bootargs is (tcp, tls, il, local!device)[] >> >> At no time during this process is the keyboard or mouse responsive. Though >> the mouse icon did become visible during the boot process. >> >> I am hoping I am wrong, but I am thinking there is some sort of driver >> issue. At the very least, checking what media there is to mount, or reading >> the SD card. And then possibly for other things, but the former could be >> gumming up the works for everything else. >> >> >>> On Jan 14, 2021, at 6:05 PM, Stuart Morrow <morrow.stu...@gmail.com >>> <mailto:morrow.stu...@gmail.com>> wrote: >>> >>> Try copying the .dtb *and* the start4 and fixup4. >>> >>> ------------------------------------------ >>> 9fans: 9fans >>> Permalink: >>> https://9fans.topicbox.com/groups/9fans/T0178132f3d2ed689-M9f2c8a9a58f03931b399b823 >>> >>> <https://9fans.topicbox.com/groups/9fans/T0178132f3d2ed689-M9f2c8a9a58f03931b399b823> >>> Delivery options: https://9fans.topicbox.com/groups/9fans/subscription >>> <https://9fans.topicbox.com/groups/9fans/subscription> >>> > > 9fans <https://9fans.topicbox.com/latest> / 9fans / see discussions > <https://9fans.topicbox.com/groups/9fans> + participants > <https://9fans.topicbox.com/groups/9fans/members> + delivery options > <https://9fans.topicbox.com/groups/9fans/subscription>Permalink > <https://9fans.topicbox.com/groups/9fans/T0178132f3d2ed689-M3e4eaa51003d3faf4b21f271> ------------------------------------------ 9fans: 9fans Permalink: https://9fans.topicbox.com/groups/9fans/T0178132f3d2ed689-M7fc239ed3107974a45f2ee07 Delivery options: https://9fans.topicbox.com/groups/9fans/subscription
