Hi Gary,
On Sun, 2014-04-13 at 03:12 -0600, Gary Thomas wrote:
> I just tried building (core-image-sato) for my BeagleBoneBlack
> using the latest Poky/Yocto master:
>
> Build Configuration:
> BB_VERSION = "1.23.0"
> BUILD_SYS = "i686-linux"
> NATIVELSBSTRING = "Fedora-13"
> TARGET_SYS = "arm-poky-linux-gnueabi"
> MACHINE = "beaglebone"
> DISTRO = "poky"
> DISTRO_VERSION = "1.6+snapshot-20140411"
> TUNE_FEATURES = "armv7a vfp neon callconvention-hard cortexa8"
> TARGET_FPU = "vfp-neon"
> meta
> meta-yocto
> meta-yocto-bsp = "master:863cc7483f5ee43189537940de8ee5c0964d24cc"
>
> This built the kernel using SRCREV 928d7b2dda
>
> I followed the bring-up instructions from README.hadware and the
> boot failed to even start the kernel. Here's what I see:
>
> =============================== boot log
> =========================================
> U-Boot 2013.07 (Apr 11 2014 - 15:03:04)
>
> I2C: ready
> DRAM: 512 MiB
> WARNING: Caches not enabled
> NAND: 0 MiB
> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
> *** Warning - readenv() failed, using default environment
>
> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
> musb-hdrc: MHDRC RTL version 2.0
> musb-hdrc: setup fifo_mode 4
> musb-hdrc: 28/31 max ep, 16384/16384 memory
> USB Peripheral mode controller at 47401000 using PIO, IRQ 0
> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
> musb-hdrc: MHDRC RTL version 2.0
> musb-hdrc: setup fifo_mode 4
> musb-hdrc: 28/31 max ep, 16384/16384 memory
> USB Host mode controller at 47401800 using PIO, IRQ 0
> Net: <ethaddr> not set. Validating first E-fuse MAC
> Phy not found
> PHY reset timed out
> cpsw, usb_ether
> Hit any key to stop autoboot: 0
> mmc0 is current device
> SD/MMC found on device 0
> reading uEnv.txt
> ** Unable to read file uEnv.txt **
> 4981688 bytes read in 613 ms (7.7 MiB/s)
> 29192 bytes read in 46 ms (619.1 KiB/s)
> Booting from mmc ...
> ## Booting kernel from Legacy Image at 80200000 ...
> Image Name: Linux-3.14.0-yocto-standard
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 4981624 Bytes = 4.8 MiB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> ## Flattened Device Tree blob at 80f80000
> Booting using the fdt blob at 0x80f80000
> Loading Kernel Image ... OK
> Using Device Tree in place at 80f80000, end 80f8a207
>
> Starting kernel ...
> ==================================================================================
>
> Any ideas what I've done wrong?
>
This is strange because last week I booted myself a BBB.
This actually looks like the serial doesn't output, perhaps the kernel
does boot. I wonder if console is right for the kernel cmdline.
On Friday I built and booted from
master:db80f796e78746014a0f9497638e5c6fd2953ef0 which is a bit earlier
that what you have but basically the same thing (updates for kernel
which should fix things, I've tested with SRCREV_meta_pn-linux-yocto =
"${AUTOREV}" those before they entered in master because I didn't had
HDMI output on my master commit).
I'm gonna rebuild from daisy tip and see what happens.
Cheers,
Stefan
> Thanks
>
> --
> ------------------------------------------------------------
> Gary Thomas | Consulting for the
> MLB Associates | Embedded world
> ------------------------------------------------------------
--
_______________________________________________
yocto mailing list
yocto@yoctoproject.org
https://lists.yoctoproject.org/listinfo/yocto
