On 2014-04-13 20:33, Denys Dmytriyenko wrote: > On Sun, Apr 13, 2014 at 03:12:16AM -0600, Gary Thomas wrote: >> I just tried building (core-image-sato) for my BeagleBoneBlack >> using the latest Poky/Yocto master: >> >> Build Configuration: >> BB_VERSION = "1.23.0" >> BUILD_SYS = "i686-linux" >> NATIVELSBSTRING = "Fedora-13" >> TARGET_SYS = "arm-poky-linux-gnueabi" >> MACHINE = "beaglebone" >> DISTRO = "poky" >> DISTRO_VERSION = "1.6+snapshot-20140411" >> TUNE_FEATURES = "armv7a vfp neon callconvention-hard cortexa8" >> TARGET_FPU = "vfp-neon" >> meta >> meta-yocto >> meta-yocto-bsp = "master:863cc7483f5ee43189537940de8ee5c0964d24cc" >> >> This built the kernel using SRCREV 928d7b2dda >> >> I followed the bring-up instructions from README.hadware and the >> boot failed to even start the kernel. Here's what I see: >> >> =============================== boot log >> ========================================= >> U-Boot 2013.07 (Apr 11 2014 - 15:03:04) >> >> I2C: ready >> DRAM: 512 MiB >> WARNING: Caches not enabled >> NAND: 0 MiB >> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 >> *** Warning - readenv() failed, using default environment >> >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >> SoftConn) >> musb-hdrc: MHDRC RTL version 2.0 >> musb-hdrc: setup fifo_mode 4 >> musb-hdrc: 28/31 max ep, 16384/16384 memory >> USB Host mode controller at 47401800 using PIO, IRQ 0 >> Net: <ethaddr> not set. Validating first E-fuse MAC >> Phy not found >> PHY reset timed out >> cpsw, usb_ether >> Hit any key to stop autoboot: 0 >> mmc0 is current device >> SD/MMC found on device 0 >> reading uEnv.txt >> ** Unable to read file uEnv.txt ** >> 4981688 bytes read in 613 ms (7.7 MiB/s) >> 29192 bytes read in 46 ms (619.1 KiB/s) >> Booting from mmc ... >> ## Booting kernel from Legacy Image at 80200000 ... >> Image Name: Linux-3.14.0-yocto-standard >> Image Type: ARM Linux Kernel Image (uncompressed) >> Data Size: 4981624 Bytes = 4.8 MiB >> Load Address: 80008000 >> Entry Point: 80008000 >> Verifying Checksum ... OK >> ## Flattened Device Tree blob at 80f80000 >> Booting using the fdt blob at 0x80f80000 >> Loading Kernel Image ... OK >> Using Device Tree in place at 80f80000, end 80f8a207 >> >> Starting kernel ... >> ================================================================================== >> >> Any ideas what I've done wrong? > > Hmm, everything looks sane. What revision is your BBB? And did you press > USER/BOOT button or erased eMMC partition per instructions? >
Revision A5A, with an LCD cape Yes, I erased the eMMC before trying this. -- ------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------ -- _______________________________________________ yocto mailing list yocto@yoctoproject.org https://lists.yoctoproject.org/listinfo/yocto
