When I log into X I seem to have the wrong resolution (My screen: vga 19"LCD envision rated at 1440x900). I am able to get around that by typing the following:
xrandr --newmode "1440x900_60.00" 106.50 1440 1528 1672 1904 900 903 909 934 -hsync +vsync xrandr --addmode VGA-0 1440x900_60.00 xrandr --output VGA-0 --mode 1440x900_60.00 I haven't been able to figure out how to make this happen automatically, i.e. how to save this as the default mode at login. If you look at the log excerpt which is attached you see that there are some modes selected there but I don't know how to change that. I don't know where those modes came from. Trying Xorg -configure was unsuccessful due to "Number of screens..." Could you make any recommendations or point me in the right direction? Thank you, Jon. [ 2142.973] (II) RADEON(0): Output VGA-0 using monitor section Monitor0 [ 2142.975] (II) RADEON(0): Output HDMI-0 has no monitor section [ 2143.204] (II) RADEON(0): EDID for output VGA-0 [ 2143.204] (II) RADEON(0): Printing probed modes for output VGA-0 [ 2143.204] (II) RADEON(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) [ 2143.204] (II) RADEON(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) [ 2143.204] (II) RADEON(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e) [ 2143.204] (II) RADEON(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e) [ 2143.204] (II) RADEON(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz e) [ 2143.206] (II) RADEON(0): EDID for output HDMI-0 [ 2143.206] (II) RADEON(0): Output VGA-0 connected [ 2143.206] (II) RADEON(0): Output HDMI-0 disconnected [ 2143.206] (II) RADEON(0): Using exact sizes for initial modes [ 2143.206] (II) RADEON(0): Output VGA-0 using initial mode 1024x768 [ 2143.206] (II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. [ 2143.206] (II) RADEON(0): mem size init: gart size :1fdff000 vram size: s:10000000 visible:fcc0000 [ 2143.206] (II) RADEON(0): EXA: Driver will allow EXA pixmaps in VRAM [ 2143.206] (==) RADEON(0): DPI set to (96, 96) _______________________________________________ xorg@lists.x.org: X.Org support Archives: http://lists.freedesktop.org/archives/xorg Info: http://lists.x.org/mailman/listinfo/xorg Your subscription address: %(user_address)s
