On Fri, 21 Mar 2003, Daniel wrote:

> Melisa,
>  
> I get the same problem (missing libglide2x.so)  with XFree86
4.2.99.902
> release (essentially 4.3) whilst trying to get my Radion 9000 pro to
run
> in X under Linux Mandrake 9.0. How did you solve this? 
> -Did you get create the soft link with the libglide3x.so rather than
> libglide2x.so 

>>no, as I was informed the libglide3x.so was used only with 3Dfx cards
>>(Note: i have no idea why the message appeared -- on reboot it did not
>>show up again).  Do you still get that message?  Were you able to make
>>Xconfig recognize your card?  Did you get your driver from ATI (I
don't
>>remember what u said)?

> I have to admit, I haven't attempted to start X since getting the
message (missing libglide2x.so) when I run Xfree86 -configure. I guess I
assumed the worst and didn't bother. Assuming the XF8Config.new looks ok
then I will try this tomorrow.

The drivers from ATI didn't work (I'm not alone in experiencing how
ineffectual they are!)

1) attempted to install the 4.2.X ATI drivers found
athttp://www.ati.com/support/drivers/linux/radeon-linux.html?cboOS=Linux
XFree86&cboProducts=RADEON+9000&eula=&choice=agree&cm
however,  when I login as root and try:
2) $>rpm -i <name of file for x server 4.2.x>     : yields no ouptut, so
do I assume everything is ok

3) $>rpm -q <name of file for x server 4.2.x>    :tells me the package
is not installed

4) $>rpm -qpl <name of file for x server4 .2.x>  : yields no output

5) Also I also can't seem to find where "fglrxconfig" is meant to be
installed let alone run it! 






>>Note: I have read a number of posts on ATI chips...most particularly
the
>>Radeon 9000. Perhaps messaging one of those people who answered
queries on
>>that type card (they tend to know one manufacturer well) would attract
>>attention? Do you keep these posts? (try [EMAIL PROTECTED] -- I
sent
>>you one of his posts that mentioned Radeon's 9000)

thanks for sending me the email from Danian - that too looks promising


> -Did you have to edit the XF86config to take account of this change (I
> have created mine with XFree86 - configure)
>  
>>My Xconfig would not work until I reduced the refresh rate to 60, the
>>color bit to 8 and selected VESA...way bad, but was able to at least
>>increase the resolution to over 800x600! 
Hmmmm sounds a bit worrying; I will bear this in mind

>>VSince I am not content (I got better results with the XFree86 version
>>that
>>came with RH7.3 -- I only went to XFree86 ver4.3 as it promised SiS300
>>support which wasn't happening under the RH7.3 version (I forget which
>>version that is)), I am gonna try to go to RH8.0 and be content till I
can
>>buy a new card... ;P

>  
> I'm beginning to see why Windows XP (which happily coexists with my
> 9000) is so popular!  
>  
>  

Without XP we wouldn't be able to exchange these e-mails! I like Linux
(as it is similar to the Solaris I use at work) but I would want to be
totally reliant on it!


So to end I will give some of your suggestions a go in a structured
fashion and see what works best 


Good night

Daniel



>>Yes, I understand that a bit! I do dual boot with Win2K still as
evidently
>>I too am far away from being ready/able to changeover;[ ! 

>>Sorry I can't help you more...I keep checking all the posts and
reading
>>elsewhere in hopes to find something that might put some light on this
>>subject. If I read anything (more), or get help from the Xconfig
>>people (before or after the upgrade), I will try to pass it on. 


mgolter
>  
>  
> Regards
>  
>  
> Daniel
>  
>  
>  
> >The linux and XFree4 install was so I can run some 3D
> applications...but I
> >did not know that glide was so specifically aimed...the Real problem
> was
> >that I couldn't get the X server configured at all.  Right now I am
> >stuck with 16 bit color...(using generic VESA in Xconfigurator, which
> is
> >not as good as what I could get with the XFree86 version that came
with
> >RH7.3!
>  
> >{I installed the 4.3 version as no other version even lists the
SiS300
> >chip...and it looks like 4.3 doesn't really support it either...)
>  
> >Thanks for info on the .so (so's I am not a gonna worry (esp since no
> >system complaints!)
>  
> ;)
>  
> mgolter
>  
>  
>  
> On Fri, 14 Mar 2003, Mike A. Harris wrote:
>  
> > On Fri, 14 Mar 2003, Melissa Golter wrote:
> > 
> > >Date: Fri, 14 Mar 2003 14:57:34 -0600 (CST)
> > >From: Melissa Golter <[EMAIL PROTECTED]>
> > >To: "'[EMAIL PROTECTED]'" <[EMAIL PROTECTED]>
> > >Cc: [EMAIL PROTECTED]
> > >Reply-To: [EMAIL PROTECTED]
> > >Content-Type: TEXT/PLAIN; charset=US-ASCII
> > >Subject: RE: Sis300 support in XFree86 version 4.3.0
> > >
> > >If I am reading the filename correctly, that file is 26Mb -- but if
> that
> > >is OK to
> > >send to you, will do...in the meantime, I put it in
> > >ftp.evl.uic.edu/pub/INcoming/mgolter/xfree/
> > >
> > >btw, ver 4.3.0 has libglide3.so but not the 2x.so nec to configure
> the
> > >system correctly.  I am supposing I can find the libglide2x.so
> somewhere
> > >(note: the previous version of XFree86 -- the one that came with
> RH7.3,
> > >did not include it either it seems (a *whereis* did not yield a
> result
> > >from the saved XFree version directory either). ;P
> > 
> > Just so you don't end up wasting your time....
> > 
> > Glide is strictly a 3Dfx low level 3D video driver library which 
> > talks directly to 3Dfx Voodoo and Banshee video hardware.
> > 
> > Glide 2 is for Voodoo Graphics I/II hardware, and Glide3 is for 
> > Voodoo 3/4/5 and Banshee hardware.
> > 
> > Glide does not work on any other video hardware, and is totally 
> > useless unless you have 3Dfx video hardware, in which case it 
> > provides the layer between DRI and the 3Dfx video card for 3D 
> > acceleration.
> > 
> > In short: You've got an SiS video card, and Glide is meaningless 
> > as far as your system is concerned.
> > 
> > -- 
> > Mike A. Harris
> > 
> > 
> > _______________________________________________
> > XFree86 mailing list
> > [EMAIL PROTECTED]
> > http://XFree86.Org/mailman/listinfo/xfree86
>  
>  
> Radion 9000 Pro ML9.0 and the m
> 




_______________________________________________
XFree86 mailing list
[EMAIL PROTECTED]
http://XFree86.Org/mailman/listinfo/xfree86

Reply via email to