Hi,

I am having pixel corruption problems with an S3 Virge DX, and XFree
4.2.1.  Whenever a portion of the screen needs to be redrawn, flickering
occurs.  In the most extreme cases, it is apparent that the flickering
pixels are duplicated from other sections of the screen.  Moving the
mouse over blank areas of the screen does not generate any pixel
corruption.

This corruption occurs above 1024x768 at depth 16.

No flickering at 24 bits up to 800x600, but after that bands of two or
three gray lines move slowly up the screen.  It's hard to tell if there
is similar corruption occuring underneath that behaviour.

To reduce the flickering, I have tried setting NoAccel and SWCusor to
true.  The only difference that made was to slow redrawing down, while
retaining the pixel corruption.

The option that seems to have helped is disabling XVideo.  This greatly
reduces the corruption.  I've also tried lowering the first value in the
1280x960 mode line:

  Modeline "1280x960" 148.50 \
      1280 1344 1504 1728 960 961 964 1011 +hsync +vsync

It defaults to 148.5.  Lowering it to 110 clears the flickering, but
causes the edges of the viewable are to bow out, so I'm guessing that
isn't the way to do it.  120 seems to be the best trade off between
flickering and screen shape.

Clutching at straws, I remember reading somewhere about X and serial
port IRQ conflicts.  The flickering and an increase in serial port silo
overflows seem to coincide.  I think that this was at the point I
upgraded to 4.2.1 from 4.0 (I think).  But I can't find that article
again.

If anyone could offer advice to clean this screen up I would appreciate
it.  I've attached my XFree86 config file and a copy of
/var/log/XFree86.0.log.  Anything else that might help to post, just
ask.

Thanks
James

Section "ServerLayout"
        Identifier     "XFree86 Configured"
        Screen      0  "Screen0" 0 0
        InputDevice    "Mouse0" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
        RgbPath      "/usr/X11R6/lib/X11/rgb"
        ModulePath   "/usr/X11R6/lib/modules"
        FontPath     "/usr/X11R6/lib/X11/fonts/local/"
        FontPath     "/usr/X11R6/lib/X11/fonts/misc/"
        FontPath     "/usr/X11R6/lib/X11/fonts/Speedo/"
        FontPath     "/usr/X11R6/lib/X11/fonts/Type1/"
        FontPath     "/usr/X11R6/lib/X11/fonts/75dpi/"
        FontPath     "/usr/X11R6/lib/X11/fonts/100dpi/"
EndSection

Section "Module"
        Load  "extmod"
        Load  "xie"
        Load  "pex5"
        Load  "glx"
        Load  "dri"
        Load  "dbe"
        Load  "record"
        Load  "xtrap"
        Load  "speedo"
        Load  "type1"
EndSection

Section "InputDevice"
        Identifier  "Keyboard0"
        Driver      "keyboard"
EndSection

Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Protocol" "auto"
        Option      "Device" "/dev/sysmouse"
        Option      "ZAxisMapping"      "4 5"
EndSection

Section "Monitor"
        ## DisplaySize    370   270     # mm
        Identifier   "Monitor0"
        VendorName   "NEC"
        ModelName    "NEC V920"
        ## HorizSync    31.5 - 82.0
        ## VertRefresh  40.0 - 150.0
        Option      "DPMS"

        ModeLine     "1280x960"  120.0 1280 1344 1504 1728 960 961 964 1011 +hsync 
+vsync
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        #Option     "slow_edodram"              # [<bool>]
        #Option     "slow_dram"                 # [<bool>]
        #Option     "fast_dram"                 # [<bool>]
        #Option     "fpm_vram"                  # [<bool>]
        #Option     "pci_burst"                 # [<bool>]
        #Option     "fifo_conservative"         # [<bool>]
        #Option     "fifo_moderate"             # [<bool>]
        #Option     "fifo_aggressive"           # [<bool>]
        #Option     "pci_retry"                 # [<bool>]
        #Option     "NoAccel"                   # [<bool>]
        #Option     "early_ras_precharge"       # [<bool>]
        #Option     "late_ras_precharge"        # [<bool>]
        #Option     "lcd_center"                # [<bool>]
        #Option     "set_lcdclk"                # <i>
        #Option     "set_mclk"                  # <freq>
        #Option     "set_refclk"                # <freq>
        #Option     "show_cache"                # [<bool>]
        #Option     "HWCursor"                  # [<bool>]
        #Option     "SWCursor"                  # [<bool>]
        #Option     "ShadowFB"                  # [<bool>]
        #Option     "Rotate"                    # [<str>]
        #Option     "UseFB"                     # [<bool>]
        #Option     "mxcr3afix"                 # [<bool>]
        Option      "XVideo"    "False"
        Identifier  "Card0"
        Driver      "s3virge"
        VendorName  "S3"
        BoardName   "ViRGE/DX or /GX"
        ChipSet     "virge dx"
        BusID       "PCI:0:20:0"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device     "Card0"
        Monitor    "Monitor0"
        DefaultDepth 16
#       SubSection "Display"
#               Depth     24
#               Modes       "1280x960" "1024x768" "800x600" "640x480"
#       EndSubSection
        SubSection "Display"
                Depth     16
                Modes       "1280x960" "1024x768" "800x600" "640x480"
        EndSubSection
        SubSection "Display"
                Depth     15
        EndSubSection
        SubSection "Display"
                Depth     8
        EndSubSection
EndSection

Section "DRI"
        Group        0
EndSection

XFree86 Version 4.2.1 / X Window System
(protocol Version 11, revision 0, vendor release 6600)
Release Date: 3 September 2002
        If the server is older than 6-12 months, or if your card is
        newer than the above date, look for a newer version before
        reporting problems.  (See http://www.XFree86.Org/)
Build Operating System: FreeBSD 4.7-RELEASE i386 [ELF] 
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
         (++) from command line, (!!) notice, (II) informational,
         (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Fri Mar 21 10:06:55 2003
(==) Using config file: "/etc/XF86Config"
(==) ServerLayout "XFree86 Configured"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(==) Keyboard: CustomKeycode disabled
(**) FontPath set to 
"/usr/X11R6/lib/X11/fonts/local/,/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(**) ModulePath set to "/usr/X11R6/lib/modules"
(--) Using syscons driver with X support (version 2.0)
(--) using VT number 9

(II) Module ABI versions:
        XFree86 ANSI C Emulation: 0.1
        XFree86 Video Driver: 0.5
        XFree86 XInput driver : 0.3
        XFree86 Server Extension : 0.1
        XFree86 Font Renderer : 0.3
(II) Loader running on freebsd
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        Module class: XFree86 Font Renderer
        ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 0.1.0
        ABI class: XFree86 Video Driver, version 0.5
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 8086,7030 card 0000,0000 rev 02 class 06,00,00 hdr 00
(II) PCI: 00:07:0: chip 8086,7000 card 0000,0000 rev 01 class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 8086,7010 card 0000,0000 rev 00 class 01,01,80 hdr 00
(II) PCI: 00:07:2: chip 8086,7020 card 0000,0000 rev 01 class 0c,03,00 hdr 00
(II) PCI: 00:13:0: chip 10ec,8139 card 1186,1301 rev 10 class 02,00,00 hdr 00
(II) PCI: 00:14:0: chip 5333,8a01 card 5333,8a01 rev 01 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) LoadModule: "scanpci"
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 0.1.0
        ABI class: XFree86 Video Driver, version 0.5
(II) UnloadModule: "scanpci"
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(II) Host-to-PCI bridge:
(II) PCI-to-ISA bridge:
(II) Bus 0: bridge is at (0:0:0), (-1,0,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus 0 I/O range:
        [0] -1  0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
        [0] -1  0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
        [0] -1  0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1: bridge is at (0:7:0), (0,-1,0), BCTRL: 0x08 (VGA_EN is set)
(II) Bus -1 I/O range:
(II) Bus -1 non-prefetchable memory range:
(II) Bus -1 prefetchable memory range:
(--) PCI:*(0:20:0) S3 ViRGE/DX or /GX rev 1, Mem @ 0xe0000000/26
(II) Addressable bus resource ranges are
        [0] -1  0x00000000 - 0xffffffff (0x0) MX[B]
        [1] -1  0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
        [0] -1  0xffe00000 - 0xffffffff (0x200000) MX[B](B)
        [1] -1  0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
        [2] -1  0x000f0000 - 0x000fffff (0x10000) MX[B]
        [3] -1  0x000c0000 - 0x000effff (0x30000) MX[B]
        [4] -1  0x00000000 - 0x0009ffff (0xa0000) MX[B]
        [5] -1  0x0000ffff - 0x0000ffff (0x1) IX[B]
        [6] -1  0x00000000 - 0x000000ff (0x100) IX[B]
(II) Active PCI resource ranges:
        [0] -1  0xe4000000 - 0xe7ffffff (0x4000000) MX[B]E
        [1] -1  0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
        [2] -1  0x00006100 - 0x000061ff (0x100) IX[B]E
        [3] -1  0x00006000 - 0x000060ff (0x100) IX[B]E
        [4] -1  0x0000f000 - 0x0000f0ff (0x100) IX[B]E
(II) Active PCI resource ranges after removing overlaps:
        [0] -1  0xe4000000 - 0xe7ffffff (0x4000000) MX[B]E
        [1] -1  0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
        [2] -1  0x00006100 - 0x000061ff (0x100) IX[B]E
        [3] -1  0x00006000 - 0x000060ff (0x100) IX[B]E
        [4] -1  0x0000f000 - 0x0000f0ff (0x100) IX[B]E
(II) OS-reported resource ranges after removing overlaps with PCI:
        [0] -1  0xffe00000 - 0xffffffff (0x200000) MX[B](B)
        [1] -1  0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
        [2] -1  0x000f0000 - 0x000fffff (0x10000) MX[B]
        [3] -1  0x000c0000 - 0x000effff (0x30000) MX[B]
        [4] -1  0x00000000 - 0x0009ffff (0xa0000) MX[B]
        [5] -1  0x0000ffff - 0x0000ffff (0x1) IX[B]
        [6] -1  0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
        [0] -1  0xffe00000 - 0xffffffff (0x200000) MX[B](B)
        [1] -1  0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
        [2] -1  0x000f0000 - 0x000fffff (0x10000) MX[B]
        [3] -1  0x000c0000 - 0x000effff (0x30000) MX[B]
        [4] -1  0x00000000 - 0x0009ffff (0xa0000) MX[B]
        [5] -1  0xe4000000 - 0xe7ffffff (0x4000000) MX[B]E
        [6] -1  0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
        [7] -1  0x0000ffff - 0x0000ffff (0x1) IX[B]
        [8] -1  0x00000000 - 0x000000ff (0x100) IX[B]
        [9] -1  0x00006100 - 0x000061ff (0x100) IX[B]E
        [10] -1 0x00006000 - 0x000060ff (0x100) IX[B]E
        [11] -1 0x0000f000 - 0x0000f0ff (0x100) IX[B]E
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) LoadModule: "xie"
(II) Loading /usr/X11R6/lib/modules/extensions/libxie.a
(II) Module xie: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension XIE
(II) LoadModule: "pex5"
(II) Loading /usr/X11R6/lib/modules/extensions/libpex5.a
(II) Module pex5: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension X3D-PEX
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
(II) Module dri: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading sub module "drm"
(II) LoadModule: "drm"
(II) Loading /usr/X11R6/lib/modules/freebsd/libdrm.a
(II) Module drm: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension XFree86-DRI
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "record"
(II) Loading /usr/X11R6/lib/modules/extensions/librecord.a
(II) Module record: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.13.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension RECORD
(II) LoadModule: "xtrap"
(II) Loading /usr/X11R6/lib/modules/extensions/libxtrap.a
(II) Module xtrap: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        Module class: XFree86 Server Extension
        ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension DEC-XTRAP
(II) LoadModule: "speedo"
(II) Loading /usr/X11R6/lib/modules/fonts/libspeedo.a
(II) Module speedo: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.1
        Module class: XFree86 Font Renderer
        ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Speedo
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.1
        Module class: XFree86 Font Renderer
        ABI class: XFree86 Font Renderer, version 0.3
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "s3virge"
(II) Loading /usr/X11R6/lib/modules/drivers/s3virge_drv.o
(II) Module s3virge: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.8.3
        Module class: XFree86 Video Driver
        ABI class: XFree86 Video Driver, version 0.5
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        Module class: XFree86 XInput Driver
        ABI class: XFree86 XInput driver, version 0.3
(II) S3VIRGE: driver (version 1.8.3) for S3 ViRGE chipsets: virge, 86C325,
        virge vx, 86C988, virge dx, virge gx, 86C375, 86C385, virge gx2,
        86C357, virge mx, 86C260, virge mx+, 86C280, trio 3d, 86C365,
        trio 3d/2x, 86C362, 86C368
(II) Primary Device is: PCI 00:14:0
(**) Chipset override: virge dx
(**) Chipset virge dx found
(II) resource ranges after xf86ClaimFixedResources() call:
        [0] -1  0xffe00000 - 0xffffffff (0x200000) MX[B](B)
        [1] -1  0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
        [2] -1  0x000f0000 - 0x000fffff (0x10000) MX[B]
        [3] -1  0x000c0000 - 0x000effff (0x30000) MX[B]
        [4] -1  0x00000000 - 0x0009ffff (0xa0000) MX[B]
        [5] -1  0xe4000000 - 0xe7ffffff (0x4000000) MX[B]E
        [6] -1  0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
        [7] -1  0x0000ffff - 0x0000ffff (0x1) IX[B]
        [8] -1  0x00000000 - 0x000000ff (0x100) IX[B]
        [9] -1  0x00006100 - 0x000061ff (0x100) IX[B]E
        [10] -1 0x00006000 - 0x000060ff (0x100) IX[B]E
        [11] -1 0x0000f000 - 0x0000f0ff (0x100) IX[B]E
(II) resource ranges after probing:
        [0] -1  0xffe00000 - 0xffffffff (0x200000) MX[B](B)
        [1] -1  0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
        [2] -1  0x000f0000 - 0x000fffff (0x10000) MX[B]
        [3] -1  0x000c0000 - 0x000effff (0x30000) MX[B]
        [4] -1  0x00000000 - 0x0009ffff (0xa0000) MX[B]
        [5] -1  0xe4000000 - 0xe7ffffff (0x4000000) MX[B]E
        [6] -1  0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
        [7] 0   0x000a0000 - 0x000affff (0x10000) MS[B]
        [8] 0   0x000b0000 - 0x000b7fff (0x8000) MS[B]
        [9] 0   0x000b8000 - 0x000bffff (0x8000) MS[B]
        [10] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
        [11] -1 0x00000000 - 0x000000ff (0x100) IX[B]
        [12] -1 0x00006100 - 0x000061ff (0x100) IX[B]E
        [13] -1 0x00006000 - 0x000060ff (0x100) IX[B]E
        [14] -1 0x0000f000 - 0x0000f0ff (0x100) IX[B]E
        [15] 0  0x000003b0 - 0x000003bb (0xc) IS[B]
        [16] 0  0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 0.1.0
        ABI class: XFree86 Video Driver, version 0.5
(**) S3VIRGE(0): Depth 16, (--) framebuffer bpp 16
(==) S3VIRGE(0): RGB weight 565
(==) S3VIRGE(0): Default visual is TrueColor
(**) S3VIRGE(0): Option "XVideo" "False"
(==) S3VIRGE(0): Using HW Cursor
(==) S3VIRGE(0): Using fb.
(==) S3VIRGE(0): mx_cr3a_fix.
(**) S3VIRGE(0): Disabling XVideo.
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 Video Driver, version 0.5
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/libint10.a
(II) Module int10: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 Video Driver, version 0.5
(II) S3VIRGE(0): initializing int10
(II) S3VIRGE(0): Primary V_BIOS segment is: 0xc000
(II) S3VIRGE(0): VESA BIOS detected
(II) S3VIRGE(0): VESA VBE Version 2.0
(II) S3VIRGE(0): VESA VBE Total Mem: 4096 kB
(II) S3VIRGE(0): VESA VBE OEM: S3 Incorporated. ViRGE /DX /GX
(II) S3VIRGE(0): VESA VBE OEM Software Rev: 1.1
(II) S3VIRGE(0): VESA VBE OEM Vendor: S3 Incorporated.
(II) S3VIRGE(0): VESA VBE OEM Product: ViRGE /DX /GX
(II) S3VIRGE(0): VESA VBE OEM Product Rev: Rev B
(**) S3VIRGE(0): Chipset: "virge dx"
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 Video Driver, version 0.5
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) S3VIRGE(0): VESA VBE DDC supported
(II) S3VIRGE(0): VESA VBE DDC Level 2
(II) S3VIRGE(0): VESA VBE DDC transfer in appr. 1 sec.
(II) S3VIRGE(0): VESA VBE DDC read successfully
(II) S3VIRGE(0): Manufacturer: NEC  Model: 5dc1  Serial#: 16843009
(II) S3VIRGE(0): Year: 2000  Week: 44
(II) S3VIRGE(0): EDID Version: 1.2
(II) S3VIRGE(0): Analog Display Input,  Input Voltage Level: 0.700/0.300 V
(II) S3VIRGE(0): Sync:  Separate  Composite
(II) S3VIRGE(0): Max H-Image Size [cm]: horiz.: 37  vert.: 27
(II) S3VIRGE(0): Gamma: 2.20
(II) S3VIRGE(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) S3VIRGE(0): First detailed timing is preferred mode
(II) S3VIRGE(0): redX: 0.629 redY: 0.330   greenX: 0.281 greenY: 0.600
(II) S3VIRGE(0): blueX: 0.148 blueY: 0.068   whiteX: 0.283 whiteY: 0.297
(II) S3VIRGE(0): Supported VESA Video Modes:
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED] (interlaced)
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): [EMAIL PROTECTED]
(II) S3VIRGE(0): Manufacturer's mask: 0
(II) S3VIRGE(0): Supported Future Video Modes:
(II) S3VIRGE(0): #0: hsize: 640  vsize 480  refresh: 85  vid: 22833
(II) S3VIRGE(0): #1: hsize: 800  vsize 600  refresh: 85  vid: 22853
(II) S3VIRGE(0): #2: hsize: 1024  vsize 768  refresh: 85  vid: 22881
(II) S3VIRGE(0): #3: hsize: 1152  vsize 864  refresh: 75  vid: 20337
(II) S3VIRGE(0): #4: hsize: 1280  vsize 960  refresh: 85  vid: 22913
(II) S3VIRGE(0): #5: hsize: 1280  vsize 1024  refresh: 85  vid: 39297
(II) S3VIRGE(0): #6: hsize: 1600  vsize 1200  refresh: 75  vid: 20393
(II) S3VIRGE(0): #7: hsize: 1920  vsize 1440  refresh: 60  vid: 16593
(II) S3VIRGE(0): Supported additional Video Mode:
(II) S3VIRGE(0): clock: 157.5 MHz   Image Size:  356 x 267 mm
(II) S3VIRGE(0): h_active: 1280  h_sync: 1344  h_sync_end 1504 h_blank_end 1728 
h_border: 0
(II) S3VIRGE(0): v_active: 1024  v_sync: 1025  v_sync_end 1028 v_blanking: 1072 
v_border: 0
(II) S3VIRGE(0): Ranges: V min: 55  V max: 160 Hz, H min: 31  H max: 96 kHz, PixClock 
max 240 MHz
(II) S3VIRGE(0): Monitor name: NEC V920
(II) S3VIRGE(0): Serial No: 0Y00105YA
(==) S3VIRGE(0): Using gamma correction (1.0, 1.0, 1.0)
(--) S3VIRGE(0): videoram:  4096k
(--) S3VIRGE(0): Detected current MCLK value of 40.091 MHz
(WW) S3VIRGE(0): Monitor0: Using default hsync range of 31.00-96.00kHz
(WW) S3VIRGE(0): Monitor0: using default vrefresh range of 55.00-160.00Hz
(II) S3VIRGE(0): Clock range:  20.00 to 270.00 MHz
(II) S3VIRGE(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1600x1200" (horizontal timing out of range)
(II) S3VIRGE(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) S3VIRGE(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) S3VIRGE(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan)
(--) S3VIRGE(0): Virtual size is 1280x960 (pitch 1280)
(**) S3VIRGE(0): Mode "1280x960": 120.0 MHz, 69.4 kHz, 68.7 Hz
(II) S3VIRGE(0): Modeline "1280x960"  120.00  1280 1344 1504 1728  960 961 964 1011 
+hsync +vsync
(**) S3VIRGE(0): Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz
(II) S3VIRGE(0): Modeline "1024x768"   94.50  1024 1072 1168 1376  768 769 772 808 
+hsync +vsync
(**) S3VIRGE(0): Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(II) S3VIRGE(0): Modeline "800x600"   56.30  800 832 896 1048  600 601 604 631 +hsync 
+vsync
(**) S3VIRGE(0): Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz
(II) S3VIRGE(0): Modeline "640x480"   36.00  640 696 752 832  480 481 484 509 -hsync 
-vsync
(--) S3VIRGE(0): Display dimensions: (370, 270) mm
(--) S3VIRGE(0): DPI set to (87, 90)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 ANSI C Emulation, version 0.1
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 1.0.0
        ABI class: XFree86 Video Driver, version 0.5
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="The XFree86 Project"
        compiled for 4.2.1, module version = 0.1.0
        ABI class: XFree86 Video Driver, version 0.5
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
        [0] 0   0xe0000000 - 0xe3ffffff (0x4000000) MS[B]
        [1] -1  0xffe00000 - 0xffffffff (0x200000) MX[B](B)
        [2] -1  0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
        [3] -1  0x000f0000 - 0x000fffff (0x10000) MX[B]
        [4] -1  0x000c0000 - 0x000effff (0x30000) MX[B]
        [5] -1  0x00000000 - 0x0009ffff (0xa0000) MX[B]
        [6] -1  0xe4000000 - 0xe7ffffff (0x4000000) MX[B]E
        [7] -1  0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
        [8] 0   0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
        [9] 0   0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
        [10] 0  0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
        [11] -1 0x0000ffff - 0x0000ffff (0x1) IX[B]
        [12] -1 0x00000000 - 0x000000ff (0x100) IX[B]
        [13] -1 0x00006100 - 0x000061ff (0x100) IX[B]E
        [14] -1 0x00006000 - 0x000060ff (0x100) IX[B]E
        [15] -1 0x0000f000 - 0x0000f0ff (0x100) IX[B]E
        [16] 0  0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
        [17] 0  0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) S3VIRGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(**) S3VIRGE(0): Using FB
(II) S3VIRGE(0): Using XFree86 Acceleration Architecture (XAA)
        Screen to screen bit blits
        Solid filled rectangles
        8x8 mono pattern filled rectangles
        CPU to Screen color expansion
        Solid Horizontal and Vertical Lines
        Image Writes
        Offscreen Pixmaps
        Setting up tile and stipple cache:
                26 128x128 slots
                6 256x256 slots
(==) S3VIRGE(0): Backing store disabled
(==) S3VIRGE(0): Silken mouse enabled
(**) Option "dpms"
(**) S3VIRGE(0): DPMS enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
PEXExtensionInit: Couldn't open default PEX font file  Roman_M
(**) Option "Protocol" "auto"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: Core Pointer
(**) Option "Device" "/dev/sysmouse"
(**) Option "ZAxisMapping" "4 5"
(**) Mouse0: ZAxisMapping: buttons 4 and 5
(**) Mouse0: Buttons: 5
(II) Keyboard "Keyboard0" handled by legacy driver
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(II) Mouse0: SetupAuto: hw.iftype is 4, hw.model is 0
(II) Mouse0: SetupAuto: protocol is SysMouse
(**) Option "BaudRate" "1200"
(**) Option "BaudRate" "1200"
(**) Option "StopBits" "2"
(**) Option "DataBits" "8"
(**) Option "Parity" "None"
(**) Option "Vmin" "1"
(**) Option "Vtime" "0"
(**) Option "FlowControl" "None"
(II) Mouse0: SetupAuto: hw.iftype is 4, hw.model is 0
(II) Mouse0: SetupAuto: protocol is SysMouse

Reply via email to