FYI, when I get "info", I see good stuff. So weewx can talk to the device
OK. :-/
rob@pi4:/etc/weewx $ weectl device weewx.conf --info
Using configuration file weewx.conf
Using driver weewx.drivers.vantage.
Using Vantage driver version 3.6.3 (weewx.drivers.vantage)
Querying...
Davis Vantage EEPROM settings:
CONSOLE TYPE: Vantage Vue
CONSOLE FIRMWARE:
Date: Feb 3 2015
Version: 4.18
CONSOLE SETTINGS:
Archive interval: 300 (seconds)
Altitude: 150 (foot)
Wind cup type: large
Rain bucket type: 0.01 inches
Rain year start: 1
Onboard time: 2025-10-14 18:08:22
CONSOLE DISPLAY UNITS:
Barometer: mbar
Temperature: degree_F
Rain: inch
Wind: mile_per_hour
CONSOLE STATION INFO:
Latitude (onboard): +47.6
Longitude (onboard): -122.3
Use manual or auto DST? AUTO
DST setting: N/A
Use GMT offset or zone code? ZONE_CODE
Time zone code: 4
GMT offset: N/A
Temperature logging: LAST
TRANSMITTERS:
Channel Receive Retransmit Repeater Type
1 active N NONE iss
2 inactive N NONE (N/A)
3 inactive N NONE (N/A)
4 inactive N NONE (N/A)
5 inactive N NONE (N/A)
6 inactive N NONE (N/A)
7 inactive N NONE (N/A)
8 inactive N NONE (N/A)
RECEPTION STATS:
Total packets received: 9832
Total packets missed: 15605
Number of resynchronizations: 1
Longest good stretch: 8
Number of CRC errors: 5459
BAROMETER CALIBRATION DATA:
Current barometer reading: 30.032 inHg
Altitude: 150 feet
Dew point: 42 F
Virtual temperature: 49 F
Humidity correction factor: 1.8
Correction ratio: 1.006
Correction constant: +0.000 inHg
Gain: 0.000
Offset: -33.000
OFFSETS:
Wind direction: +0 deg
Inside Temperature: +0.0 F
Inside Humidity: +0 %
Outside Temperature: +0.0 F
Outside Humidity: +0 %
On Tuesday, October 14, 2025 at 5:59:51 PM UTC-7 Rob Cranfill wrote:
> And my station is a Vangage VUE; the config section for that is, as it was
> before,
>
> [Vantage]
> # This section is for the Davis Vantage series of weather stations.
>
> # Connection type: serial or ethernet
> # serial (the classic VantagePro)
> # ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
> type = serial
>
> # If the connection type is serial, a port must be specified:
> # Debian, Ubuntu, Redhat, Fedora, and SuSE:
> # /dev/ttyUSB0 is a common USB port name
> # /dev/ttyS0 is a common serial port name
> # BSD:
> # /dev/cuaU0 is a common serial port name
> port = /dev/ttyUSB0
>
>
> On Tuesday, October 14, 2025 at 5:39:06 PM UTC-7 Rob Cranfill wrote:
>
>> I should have mentioned I have been installing/upgrading via the
>> "configure apt" method - not a .deb file, as detailed at
>> https://weewx.com/docs/5.2/quickstarts/debian/.
>> /r
>>
>>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion visit
https://groups.google.com/d/msgid/weewx-user/0385c686-fd60-48cd-a322-c1c27fd93294n%40googlegroups.com.
