Thanks for the help Gary. I was literally 2 hours away at the beach, away
from my Pi at the time that it's stuck at, so I know I didn't make any
changes intentionally. The only correlation I can come up close to the
11:55pm time that it's stuck at is, each night @ 11:59pm via a cron job, I
stop weewx, back it up and then restart it. Based on /var/log/messages, it
was back up and running 18 seconds later.
pi@corbett:~ $ wee_debug --info
Using verbosity=1, displaying most info
wee_debug output will be sent to stdout(console)
Using configuration file /etc/weewx/weewx.conf
Using database binding 'wx_binding', which is bound to database
'archive_sqlite'
System info
Platform: Linux-4.19.66-v7+-armv7l-with-debian-9.13
Python Version: 2.7.13
Load Information
1 minute load average: 0.00
5 minute load average: 0.00
15 minute load average: 0.00
General Weewx info
Weewx version 4.2.0 detected.
Station info
Station type: Vantage
Driver: weewx.drivers.vantage
Driver info
[Vantage]
# This section is for the Davis Vantage series of weather stations.
# Connection type: serial or ethernet
# serial (the classic VantagePro)
# ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
type = serial
# If the connection type is serial, a port must be specified:
# Debian, Ubuntu, Redhat, Fedora, and SuSE:
# /dev/ttyUSB0 is a common USB port name
# /dev/ttyS0 is a common serial port name
# BSD:
# /dev/cuaU0 is a common serial port name
port = /dev/ttyUSB0
# If the connection type is ethernet, an IP Address/hostname is
required:
host = 1.2.3.4
######################################################
# The rest of this section rarely needs any attention.
# You can safely leave it "as is."
######################################################
# Serial baud rate (usually 19200)
baudrate = 19200
# TCP port (when using the WeatherLinkIP)
tcp_port = 22222
# TCP send delay (when using the WeatherLinkIP):
tcp_send_delay = 0.5
# The type of LOOP packet to request: 1 = LOOP1; 2 = LOOP2; 3 = both
loop_request = 1
# The id of your ISS station (usually 1). If you use a wind meter
connected
# to a anemometer transmitter kit, use its id
iss_id = 1
# How long to wait for a response from the station before giving up (in
# seconds; must be greater than 2)
timeout = 4
# How long to wait before trying again (in seconds)
wait_before_retry = 1.2
# How many times to try before giving up:
max_tries = 4
# Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2
model_type = 2
# The driver to use:
driver = weewx.drivers.vantage
Currently installed extensions
Extension Name Version Description
mqtt 0.23 Upload weather data to MQTT server.
forecast 3.3.2 Generate and display weather and tide forecasts.
Archive info
Database name: weewx.sdb
Table name: archive
Version 2
Unit system: 1 (US)
First good timestamp: 2019-07-03 21:35:00 PDT (1562214900)
Last good timestamp: 2021-01-03 20:10:00 PST (1609733400)
Number of records: 156772
weewx (weewx.conf) is set to use an archive interval of 300 seconds.
The station hardware was not interrogated in determining archive interval.
Databases configured in weewx.conf
Database name: weewx.sdb
Database driver: weedb.sqlite
Database name: weewx
Database driver: weedb.mysql
Database host: localhost
Database name: forecast.sdb
Database driver: weedb.sqlite
Parsed and obfuscated weewx.conf
# WEEWX CONFIGURATION FILE
#
# Copyright (c) 2009-2019 Tom Keffer <tkef...@gmail.com>
# See the file LICENSE.txt for your rights.
##############################################################################
# This section is for general configuration information.
# Set to 1 for extra debug info, otherwise comment it out or set to zero
debug = 1
# Root directory of the weewx data file hierarchy for this station
WEEWX_ROOT = /
# Whether to log successful operations
log_success = True
# Whether to log unsuccessful operations
log_failure = True
# How long to wait before timing out a socket (FTP, HTTP) connection
socket_timeout = 20
# Do not modify this. It is used when installing and updating weewx.
version = 4.2.0
##############################################################################
# This section is for information about the station.
[Station]
# Description of the station location
location = "Corbett Ln. : Portland, OR"
# Latitude and longitude in decimal degrees
latitude = 45.4557641
longitude = -122.6769627
# Altitude of the station, with unit it is in. This is downloaded from
# from the station if the hardware supports it.
altitude = 475, foot
# Set to type of station hardware. There must be a corresponding stanza
# in this file with a 'driver' parameter indicating the driver to be
used.
station_type = Vantage
# If you have a website, you may specify an URL
station_url = XXX obfuscated by wee_debug XXX
# The start of the rain year (1=January; 10=October, etc.). This is
# downloaded from the station if the hardware supports it.
rain_year_start = 10
# Start of week (0=Monday, 6=Sunday)
week_start = 6
##############################################################################
[Vantage]
# This section is for the Davis Vantage series of weather stations.
# Connection type: serial or ethernet
# serial (the classic VantagePro)
# ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
type = serial
# If the connection type is serial, a port must be specified:
# Debian, Ubuntu, Redhat, Fedora, and SuSE:
# /dev/ttyUSB0 is a common USB port name
# /dev/ttyS0 is a common serial port name
# BSD:
# /dev/cuaU0 is a common serial port name
port = /dev/ttyUSB0
# If the connection type is ethernet, an IP Address/hostname is
required:
host = 1.2.3.4
######################################################
# The rest of this section rarely needs any attention.
# You can safely leave it "as is."
######################################################
# Serial baud rate (usually 19200)
baudrate = 19200
# TCP port (when using the WeatherLinkIP)
tcp_port = 22222
# TCP send delay (when using the WeatherLinkIP):
tcp_send_delay = 0.5
# The type of LOOP packet to request: 1 = LOOP1; 2 = LOOP2; 3 = both
loop_request = 1
# The id of your ISS station (usually 1). If you use a wind meter
connected
# to a anemometer transmitter kit, use its id
iss_id = 1
# How long to wait for a response from the station before giving up (in
# seconds; must be greater than 2)
timeout = 4
# How long to wait before trying again (in seconds)
wait_before_retry = 1.2
# How many times to try before giving up:
max_tries = 4
# Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2
model_type = 2
# The driver to use:
driver = weewx.drivers.vantage
##############################################################################
[AcuRite]
# This section is for AcuRite weather stations.
# The station model, e.g., 'AcuRite 01025' or 'AcuRite 02032C'
model = AcuRite 01036
# The driver to use:
driver = weewx.drivers.acurite
##############################################################################
# This section is for uploading data to Internet sites
[StdRESTful]
[[MQTT]]
server_url = XXX obfuscated by wee_debug XXX
topic = corbett/weather
retain = True
[[StationRegistry]]
# To register this weather station with weewx, set this to true
register_this_station = true
[[AWEKAS]]
# This section is for configuring posts to AWEKAS.
# If you wish to do this, set the option 'enable' to true,
# and specify a username and password.
# To guard against parsing errors, put the password in quotes.
enable = false
username = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[CWOP]]
# This section is for configuring posts to CWOP.
# If you wish to do this, set the option 'enable' to true,
# and specify the station ID (e.g., CW1234).
enable = false
station = XXX obfuscated by wee_debug XXX
# If this is an APRS (radio amateur) station, uncomment
# the following and replace with a passcode (e.g., 12345).
#passcode = replace_me (APRS stations only)
[[PWSweather]]
# This section is for configuring posts to PWSweather.com.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
# To guard against parsing errors, put the password in quotes.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[WOW]]
# This section is for configuring posts to WOW.
# If you wish to do this, set the option 'enable' to true,
# and specify a station and password.
# To guard against parsing errors, put the password in quotes.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
[[Wunderground]]
# This section is for configuring posts to the Weather Underground.
# If you wish to do this, set the option 'enable' to true,
# and specify a station (e.g., 'KORHOODR3') and password.
# To guard against parsing errors, put the password in quotes.
enable = false
station = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
# Set the following to True to have weewx use the WU "Rapidfire"
# protocol. Not all hardware can support it. See the User's Guide.
rapidfire = false
# If you plan on using wunderfixer, set the following
# to your API key:
api_key = XXX obfuscated by wee_debug XXX
##############################################################################
# This section specifies what reports, using which skins, to generate.
[StdReport]
# Where the skins reside, relative to WEEWX_ROOT
SKIN_ROOT = /etc/weewx/skins
# Where the generated reports should go, relative to WEEWX_ROOT
HTML_ROOT = /var/www/html/weewx
# The database binding indicates which data should be used in reports.
data_binding = wx_binding
# Whether to log a successful operation
log_success = True
# Whether to log an unsuccessful operation
log_failure = False
####
# Each of the following subsections defines a report that will be run.
# See the customizing guide to change the units, plot types and line
# colors, modify the fonts, display additional sensor data, and other
# customizations. Many of those changes can be made here by overriding
# parameters, or by modifying templates within the skin itself.
[[SeasonsReport]]
# The SeasonsReport uses the 'Seasons' skin, which contains the
# images, templates and plots for the report.
skin = Seasons
enable = true
[[[CheetahGenerator]]]
search_list_extensions = user.forecast.ForecastVariables
[[[CopyGenerator]]]
copy_once = seasons.css, seasons.js, favicon.ico, font/*.woff,
font/*.woff2, forecast_strip.css, icons/*
[[SmartphoneReport]]
# The SmartphoneReport uses the 'Smartphone' skin, and the images
and
# files are placed in a dedicated subdirectory.
skin = Smartphone
enable = true
HTML_ROOT = /var/www/html/weewx/smart/
[[MobileReport]]
# The MobileReport uses the 'Mobile' skin, and the images and files
# are placed in a dedicated subdirectory.
skin = Mobile
enable = true
HTML_ROOT = /var/www/html/weewx/mobile/
[[StandardReport]]
# This is the old "Standard" skin. By default, it is not enabled.
skin = Standard
enable = true
HTML_ROOT = /var/www/html/weewx/standard
[[forecast]]
enable = false
HTML_ROOT = /var/www/html/weewx/forecast
skin = forecast
[[FTP]]
# FTP'ing the results to a webserver is treated as just another
report,
# albeit one with an unusual report generator!
skin = Ftp
# If you wish to use FTP, set "enable" to "true", then
# fill out the next four lines.
# Use quotes around passwords to guard against parsing errors.
enable = false
user = XXX obfuscated by wee_debug XXX
password = XXX obfuscated by wee_debug XXX
server = replace_me # The ftp server name, e.g, www.myserver.org
path = replace_me # The destination directory, e.g., /weather
# Set to True for an FTP over TLS (FTPS) connection. Not all servers
# support this.
secure_ftp = False
# To upload files from something other than what HTML_ROOT is set
# to above, specify a different HTML_ROOT here.
#HTML_ROOT = /var/www/html/weewx
# Most FTP servers use port 21
port = 21
# Set to 1 to use passive mode, zero for active mode
passive = 1
[[RSYNC]]
# rsync'ing to a webserver is treated as just another report
skin = Rsync
# If you wish to use rsync, you must configure passwordless ssh
using
# public/private key authentication from the user account that weewx
# runs to the user account on the remote machine where the files
# will be copied.
#
# If you wish to use rsync, set "enable" to "true", then
# fill out server, user, and path.
# The server should appear in your .ssh/config file.
# The user is the username used in the identity file.
# The path is the destination directory, such as
/var/www/html/weather.
# Be sure that the user has write permissions on the destination!
enable = false
server = replace_me
user = XXX obfuscated by wee_debug XXX
path = replace_me
# To upload files from something other than what HTML_ROOT is set
# to above, specify a different HTML_ROOT here.
#HTML_ROOT = /var/www/html/weewx
# Rsync can be configured to remove files from the remote server if
# they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you
# make a mistake in the remote path, you could could unintentionally
# cause unrelated files to be deleted. Set to 1 to enable remote
file
# deletion, zero to allow files to accumulate remotely.
delete = 0
####
# Various options for customizing your reports.
[[Defaults]]
[[[Units]]]
# The following section sets what unit to use for each unit
group.
# NB: The unit is always in the singular. I.e., 'mile_per_hour',
# NOT 'miles_per_hour'
[[[[Groups]]]]
group_altitude = foot # Options are 'foot' or 'meter'
group_degree_day = degree_F_day # Options are
'degree_F_day' or 'degree_C_day'
group_pressure = inHg # Options are 'inHg', 'mmHg',
'mbar', or 'hPa'
group_rain = inch # Options are 'inch', 'cm', or 'mm'
group_rainrate = inch_per_hour # Options are
'inch_per_hour', 'cm_per_hour', or 'mm_per_hour'
group_speed = mile_per_hour # Options are
'mile_per_hour', 'km_per_hour', 'knot', or 'meter_per_second'
group_speed2 = mile_per_hour2 # Options are
'mile_per_hour2', 'km_per_hour2', 'knot2', or 'meter_per_second2'
group_temperature = degree_F # Options are 'degree_F' or
'degree_C'
group_distance = mile
# The following section sets the formatting for each type of
unit.
[[[[StringFormats]]]]
centibar = %.0f
cm = %.2f
cm_per_hour = %.2f
degree_C = %.1f
degree_F = %.1f
degree_compass = %.0f
foot = %.0f
hPa = %.1f
hour = %.1f
inHg = %.3f
inch = %.2f
inch_per_hour = %.2f
km_per_hour = %.0f
km_per_hour2 = %.1f
knot = %.0f
knot2 = %.1f
mbar = %.1f
meter = %.0f
meter_per_second = %.1f
meter_per_second2 = %.1f
mile_per_hour = %.0f
mile_per_hour2 = %.1f
mm = %.1f
mmHg = %.1f
mm_per_hour = %.1f
percent = %.0f
second = %.0f
uv_index = %.1f
volt = %.1f
watt_per_meter_squared = %.0f
NONE = " N/A"
# The following section sets the label for each type of unit
[[[[Labels]]]]
day = " day", " days"
hour = " hour", " hours"
minute = " minute", " minutes"
second = " second", " seconds"
NONE = ""
# The following section sets the format for each time scale.
# The values below will work in every locale, but they may not
look
# particularly attractive.
[[[[TimeFormats]]]]
hour = %H:%M
day = %X
week = %X (%A)
month = %x %X
year = %x %X
rainyear = %x %X
current = %x %X
ephem_day = %X
ephem_year = %x %X
[[[[Ordinates]]]]
# Ordinal directions. The last one is for no wind direction
directions = N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW,
WSW, W, WNW, NW, NNW, N/A
# The following section sets the base temperatures used for the
# calculation of heating and cooling degree-days.
[[[[DegreeDays]]]]
# Base temperature for heating days, with unit:
heating_base = 65, degree_F
# Base temperature for cooling days, with unit:
cooling_base = 65, degree_F
# Base temperature for growing days, with unit:
growing_base = 50.0, degree_F
# A trend takes a difference across a time period. The following
# section sets the time period, and how big an error is allowed
to
# still be counted as the start or end of a period.
[[[[Trend]]]]
time_delta = 10800 # 3 hours
time_grace = 300 # 5 minutes
# The labels to be used for each observation type
[[[Labels]]]
# Set to hemisphere abbreviations suitable for your location:
hemispheres = N, S, E, W
# Formats to be used for latitude whole degrees, longitude whole
# degrees, and minutes:
latlon_formats = %02d, %03d, %05.2f
# Generic labels, keyed by an observation type.
[[[[Generic]]]]
barometer = Barometer
dewpoint = Dew Point
ET = ET
heatindex = Heat Index
inHumidity = Inside Humidity
inTemp = Inside Temperature
outHumidity = Humidity
outTemp = Outside Temperature
radiation = Radiation
rain = Rain
rainRate = Rain Rate
UV = UV Index
windDir = Wind Direction
windGust = Gust Speed
windGustDir = Gust Direction
windSpeed = Wind Speed
windchill = Wind Chill
windgustvec = Gust Vector
windvec = Wind Vector
extraTemp1 = Temperature1
extraTemp2 = Temperature2
extraTemp3 = Temperature3
# Sensor status indicators
rxCheckPercent = Signal Quality
txBatteryStatus = Transmitter Battery
windBatteryStatus = Wind Battery
rainBatteryStatus = Rain Battery
outTempBatteryStatus = Outside Temperature Battery
inTempBatteryStatus = Inside Temperature Battery
consBatteryVoltage = Console Battery
heatingVoltage = Heating Battery
supplyVoltage = Supply Voltage
referenceVoltage = Reference Voltage
[[[Almanac]]]
# The labels to be used for the phases of the moon:
moon_phases = New, Waxing crescent, First quarter, Waxing
gibbous, Full, Waning gibbous, Last quarter, Waning crescent
##############################################################################
# This service acts as a filter, converting the unit system coming from
# the hardware to a unit system in the database.
[StdConvert]
# The target_unit affects only the unit system in the database. Once
# chosen it cannot be changed without converting the entire database.
# Modification of target_unit after starting weewx will result in
# corrupt data - the database will contain a mix of US and METRIC data.
#
# The value of target_unit does not affect the unit system for
# reporting - reports can display US, Metric, or any combination of
units.
#
# In most cases, target_unit should be left as the default: US
#
# In particular, those migrating from a standard wview installation
# should use US since that is what the wview database contains.
# DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING!
target_unit = US # Options are 'US', 'METRICWX', or 'METRIC'
##############################################################################
# This section can adjust data using calibration expressions.
[StdCalibrate]
[[Corrections]]
# For each type, an arbitrary calibration expression can be given.
# It should be in the units defined in the StdConvert section.
# Example:
foo = foo + 0.2
##############################################################################
# This section is for quality control checks. If units are not specified,
# values must be in the units defined in the StdConvert section.
[StdQC]
[[MinMax]]
barometer = 26, 32.5, inHg
pressure = 24, 34.5, inHg
outTemp = -40, 120, degree_F
inTemp = 10, 120, degree_F
outHumidity = 0, 100
inHumidity = 0, 100
windSpeed = 0, 120, mile_per_hour
rain = 0, 10, inch
##############################################################################
# This section controls the origin of derived values.
[StdWXCalculate]
[[Calculations]]
# How to calculate derived quantities. Possible values are:
# hardware - use the value provided by hardware
# software - use the value calculated by weewx
# prefer_hardware - use value provide by hardware if available,
# otherwise use value calculated by weewx
pressure = prefer_hardware
barometer = prefer_hardware
altimeter = prefer_hardware
windchill = prefer_hardware
heatindex = prefer_hardware
dewpoint = prefer_hardware
inDewpoint = prefer_hardware
rainRate = prefer_hardware
maxSolarRad = prefer_hardware
cloudbase = prefer_hardware
humidex = prefer_hardware
appTemp = prefer_hardware
ET = prefer_hardware
windrun = prefer_hardware
##############################################################################
# For hardware that supports it, this section controls how often the
# onboard clock gets updated.
[StdTimeSynch]
# How often to check the weather station clock for drift (in seconds)
clock_check = 14400
# How much it can drift before we will correct it (in seconds)
max_drift = 5
##############################################################################
# This section is for configuring the archive service.
[StdArchive]
# If the station hardware supports data logging then the archive
interval
# will be downloaded from the station. Otherwise, specify it (in
seconds).
archive_interval = 300
# If possible, new archive records are downloaded from the station
# hardware. If the hardware does not support this, then new archive
# records will be generated in software.
# Set the following to "software" to force software record generation.
record_generation = software
# Whether to include LOOP data in hi/low statistics
loop_hilo = True
# The data binding used to save archive records
data_binding = wx_binding
##############################################################################
# This section binds a data store to a database.
[DataBindings]
[[wx_binding]]
# The database must match one of the sections in [Databases].
# This is likely to be the only option you would want to change.
database = archive_sqlite
# The name of the table within the database
table_name = archive
# The manager handles aggregation of data for historical summaries
manager = weewx.wxmanager.WXDaySummaryManager
# The schema defines the structure of the database.
# It is *only* used when the database is created.
schema = schemas.wview.schema
[[forecast_binding]]
database = forecast_sqlite
##############################################################################
# This section defines various databases.
[Databases]
# A SQLite database is simply a single file
[[archive_sqlite]]
database_name = weewx.sdb
database_type = SQLite
# MySQL
[[archive_mysql]]
database_name = weewx
database_type = MySQL
[[forecast_sqlite]]
database_name = forecast.sdb
database_type = SQLite
##############################################################################
# This section defines defaults for the different types of databases.
[DatabaseTypes]
# Defaults for SQLite databases
[[SQLite]]
driver = weedb.sqlite
# Directory in which the database files are located
SQLITE_ROOT = /var/lib/weewx
# Defaults for MySQL databases
[[MySQL]]
driver = weedb.mysql
# The host where the database is located
host = localhost
# The user name for logging in to the host
user = XXX obfuscated by wee_debug XXX
# The password for the user name (quotes guard against parsing
errors)
password = XXX obfuscated by wee_debug XXX
##############################################################################
# This section configures the internal weewx engine.
[Engine]
# The following section specifies which services should be run and in
what order.
[[Services]]
prep_services = weewx.engine.StdTimeSynch
data_services = ,
process_services = weewx.engine.StdConvert,
weewx.engine.StdCalibrate, weewx.engine.StdQC,
weewx.wxservices.StdWXCalculate
xtype_services = weewx.wxxtypes.StdWXXTypes,
weewx.wxxtypes.StdPressureCooker, weewx.wxxtypes.StdRainRater,
weewx.wxxtypes.StdDelta
archive_services = weewx.engine.StdArchive,
user.forecast.ZambrettiForecast, user.forecast.NWSForecast,
user.forecast.WUForecast, user.forecast.OWMForecast,
user.forecast.UKMOForecast, user.forecast.AerisForecast,
user.forecast.WWOForecast, user.forecast.DSForecast,
user.forecast.XTideForecast
restful_services = weewx.restx.StdStationRegistry,
weewx.restx.StdWunderground, weewx.restx.StdPWSweather,
weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS,
user.mqtt.MQTT
report_services = weewx.engine.StdPrint, weewx.engine.StdReport
##############################################################################
# Options for extension 'forecast'
[Forecast]
data_binding = forecast_binding
[[OWM]]
api_key = XXX obfuscated by wee_debug XXX
[[WWO]]
api_key = XXX obfuscated by wee_debug XXX
[[WU]]
api_key = XXX obfuscated by wee_debug XXX
[[NWS]]
lid = ORZ006
foid = PQR
[[UKMO]]
api_key = XXX obfuscated by wee_debug XXX
location = INSERT_UK_LOCATION_HERE
[[XTide]]
location = "INSERT_LOCATION_HERE (e.g., Boston)"
[[Zambretti]]
hemisphere = NORTH
[[Aeris]]
client_secret = INSERT_AERIS_CLIENT_SECRET_HERE
client_id = INSERT_AERIS_CLIENT_ID_HERE
[[DS]]
api_key = XXX obfuscated by wee_debug XXX
wee_debug report successfully generated
On Sun, Jan 3, 2021 at 7:31 PM gjr80 <gjroder...@gmail.com> wrote:
> Hi,
>
> That is interesting, you have debug = 1 but the detail that is showing in
> the log is less than there should be. Could you please post the output from
> wee_debug
> --info <http://weewx.com/docs/utilities.htm#wee_debug_utility>. Before
> posting the wee_debug output check to make sure there is no sensitive
> info in the output such as user names, passwords, api keys etc, wee_debug
> will obfuscate such info but it is not perfect.
>
> Gary
>
> On Monday, 4 January 2021 at 12:58:27 UTC+10 blu...@gmail.com wrote:
>
>> On my Seasons skins, for some reason the index.html file isn't getting
>> updated. I don't remember changing anything since the 1/1/21 @ 11:55pm
>> timestamp of the last update.
>>
>> The Standard and Mobile versions are both updating correctly.
>>
>> http://wx.ke7k.com/
>>
>> I changed debug = 1 and restarted....
>>
>> Jan 3 18:24:29 corbett weewx[18565] INFO __main__: Initializing weewx
>> version 4.2.0
>> Jan 3 18:24:29 corbett weewx[18565] INFO __main__: Using Python 2.7.13
>> (default, Aug 22 2020, 10:03:02) #012[GCC 6.3.0 20170516]
>> Jan 3 18:24:29 corbett weewx[18565] INFO __main__: Platform
>> Linux-4.19.66-v7+-armv7l-with-debian-9.13
>> Jan 3 18:24:29 corbett weewx[18565] INFO __main__: Locale is
>> 'en_US.UTF-8'
>> Jan 3 18:24:29 corbett weewx[18565] INFO __main__: PID file is
>> /var/run/weewx.pid
>> Jan 3 18:24:29 corbett weewx[18569] INFO __main__: Using configuration
>> file /etc/weewx/weewx.conf
>> Jan 3 18:24:29 corbett weewx[18569] INFO __main__: Debug is 1
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.engine: Loading station
>> type Vantage (weewx.drivers.vantage)
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.engine: StdConvert target
>> unit is 0x1
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.engine: Archive will use
>> data binding wx_binding
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.engine: Record generation
>> will be attempted in 'software'
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.engine: Using archive
>> interval of 300 seconds (software record generation)
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: Zambretti: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: Zambretti:
>> interval=600 max_age=604800 winddir_period=1800 pressure_period=10800
>> hemisphere=NORTH lower_pressure=950.0 upper_pressure=1050.0
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: NWS: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: NWS: interval=10800
>> max_age=604800 lid=ORZ006 foid=PQR
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: WU: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: OWM: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: UKMO: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: Aeris: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: WWO: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: DS: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewxd: forecast: MainThread: XTide: forecast
>> version 3.3.2
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.restx: StationRegistry:
>> Station will be registered.
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.restx: Wunderground:
>> Posting not enabled.
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.restx: PWSweather:
>> Posting not enabled.
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.restx: CWOP: Posting not
>> enabled.
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.restx: WOW: Posting not
>> enabled.
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.restx: AWEKAS: Posting
>> not enabled.
>> Jan 3 18:24:29 corbett weewx[18569] INFO user.mqtt: service version is
>> 0.23
>> Jan 3 18:24:29 corbett weewx[18569] INFO user.mqtt: binding to archive
>> Jan 3 18:24:29 corbett weewx[18569] INFO user.mqtt: topic is
>> corbett/weather
>> Jan 3 18:24:29 corbett weewx[18569] INFO user.mqtt: data will be
>> uploaded to mqtt://127.0.0.1:1883
>> Jan 3 18:24:29 corbett weewx[18569] INFO __main__: Starting up weewx
>> version 4.2.0
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.engine: Clock error is
>> 0.07 seconds (positive is fast)
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.engine: Using binding
>> 'wx_binding' to database 'weewx.sdb'
>> Jan 3 18:24:29 corbett weewx[18569] INFO weewx.manager: Starting
>> backfill of daily summaries
>> Jan 3 18:24:32 corbett weewx[18569] INFO weewx.engine: Starting main
>> packet loop.
>> Jan 3 18:25:14 corbett weewx[18569] INFO weewx.manager: Added record
>> 2021-01-03 18:25:00 PST (1609727100) to database 'weewx.sdb'
>> Jan 3 18:25:14 corbett weewx[18569] INFO weewx.manager: Added record
>> 2021-01-03 18:25:00 PST (1609727100) to daily summary in 'weewx.sdb'
>> Jan 3 18:25:14 corbett weewxd: forecast: NWSThread: NWS: downloading
>> forecast from '
>> http://forecast.weather.gov/product.php?site=NWS&product=PFM&format=txt&issuedby=PQR
>> '
>> Jan 3 18:25:15 corbett weewx[18569] INFO weewx.restx: MQTT: Published
>> record 2021-01-03 18:25:00 PST (1609727100)
>> Jan 3 18:25:15 corbett weewx[18569] INFO weewx.restx: StationRegistry:
>> Published record 2021-01-03 18:25:00 PST (1609727100)
>> Jan 3 18:25:15 corbett weewxd: forecast: ZambrettiThread: Zambretti:
>> generated 1 forecast record
>> Jan 3 18:25:20 corbett weewx[18569] INFO weewx.cheetahgenerator:
>> Generated 7 files for report SeasonsReport in 5.29 seconds
>> Jan 3 18:25:20 corbett weewxd: forecast: NWSThread: NWS: got 40 forecast
>> records for Scappoose-Columbia OR 45.77N 122.86W Elev. 49 ft
>> Jan 3 18:25:21 corbett weewx[18569] INFO weewx.imagegenerator: Generated
>> 14 images for report SeasonsReport in 1.05 seconds
>> Jan 3 18:25:21 corbett weewx[18569] INFO weewx.reportengine: Copied 87
>> files to /var/www/html/weewx
>> Jan 3 18:25:21 corbett weewx[18569] INFO weewx.cheetahgenerator:
>> Generated 6 files for report SmartphoneReport in 0.35 seconds
>> Jan 3 18:25:22 corbett weewx[18569] INFO weewx.imagegenerator: Generated
>> 6 images for report SmartphoneReport in 0.38 seconds
>> Jan 3 18:25:22 corbett weewx[18569] INFO weewx.reportengine: Copied 6
>> files to /var/www/html/weewx/smart/
>> Jan 3 18:25:22 corbett weewx[18569] INFO weewx.cheetahgenerator:
>> Generated 1 files for report MobileReport in 0.11 seconds
>> Jan 3 18:25:22 corbett weewx[18569] INFO weewx.imagegenerator: Generated
>> 4 images for report MobileReport in 0.26 seconds
>> Jan 3 18:25:22 corbett weewx[18569] INFO weewx.reportengine: Copied 2
>> files to /var/www/html/weewx/mobile/
>> Jan 3 18:25:26 corbett weewx[18569] INFO weewx.cheetahgenerator:
>> Generated 14 files for report StandardReport in 3.95 seconds
>> Jan 3 18:25:27 corbett weewx[18569] INFO weewx.imagegenerator: Generated
>> 12 images for report StandardReport in 0.80 seconds
>> Jan 3 18:25:27 corbett weewx[18569] INFO weewx.reportengine: Copied 14
>> files to /var/www/html/weewx/standard
>>
>>
>> --
> You received this message because you are subscribed to the Google Groups
> "weewx-user" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to weewx-user+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/weewx-user/abfd3be6-b829-4b40-98c4-751dcc0cf047n%40googlegroups.com
> <https://groups.google.com/d/msgid/weewx-user/abfd3be6-b829-4b40-98c4-751dcc0cf047n%40googlegroups.com?utm_medium=email&utm_source=footer>
> .
>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to weewx-user+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/CAHiQ_B2mpEf1BF2eycPnbA36DQ3onx10Gvg6-N2CUJ-HjcUb%3DQ%40mail.gmail.com.
