Hi,
Not a sdr driver or Acurite user but looking at the sdr driver as far as I
can tell the sdr driver expects Acurite5n1PacketV2 rain data to be in field
rain_mm whereas you appear to have rain_in. You could try adding the
following two highlighted lines to /usr/share/weewx/user/sdr.py:
if 'wind_dir_deg' in obj:
pkt['wind_dir'] = Packet.get_float(obj, 'wind_dir_deg')
if 'rain_mm' in obj:
pkt['rain_total'] = Packet.get_float(obj, 'rain_mm') / 25.4
if 'rain_in' in obj:
pkt['rain_total'] = Packet.get_float(obj, 'rain_in')
if 'temperature_F' in obj:
pkt['temperature'] = Packet.get_float(obj, 'temperature_F')
Save sdr.py then try running sdr.py directly again.
Oh, and of course, make sure you keep a back of sdr.py before making any
changes.
Gary
On Thursday, 21 May 2020 12:54:38 UTC+10, Andrew Mackey wrote:
>
> After installing the rtl software and the weewx software on my Pi 4 and
> getting everything configured I am getting things to work as expected.
> Just no rain data. I was expecting to have this problem because the
> output from running the command sudo PYTHONPATH=/usr/share/weewx python
> /usr/share/weewx/user/sdr.py --cmd="rtl_433 -M utc -F json" is missing the
> rain data in the parsed section. Notice in the output below that there is
> a value in the 'rain_in' for the out section, but that rain data is not in
> the parsed section.
>
>
> out:[u'{"time" : "2020-05-21 02:27:42", "model" : "Acurite-5n1", "subtype"
> : 49, "id" : 1066, "channel" : "B", "sequence_num" : 0, "battery_ok" : 1,
> "wind_avg_km_h" : 14.245, "wind_dir_deg" : 112.500, "rain_in" : 28.500,
> "mic" : "CHECKSUM"}\n', u'{"time" : "2020-05-21 02:27:42", "model" :
> "Acurite-5n1", "subtype" : 49, "id" : 1066, "channel" : "B", "sequence_num"
> : 1, "battery_ok" : 1, "wind_avg_km_h" : 14.245, "wind_dir_deg" : 112.500,
> "rain_in" : 28.500, "mic" : "CHECKSUM"}\n', u'{"time" : "2020-05-21
> 02:27:42", "model" : "Acurite-5n1", "subtype" : 49, "id" : 1066, "channel"
> : "B", "sequence_num" : 2, "battery_ok" : 1, "wind_avg_km_h" : 14.245,
> "wind_dir_deg" : 112.500, "rain_in" : 28.500, "mic" : "CHECKSUM"}\n']
>
>
> parsed: {'wind_speed.042A.Acurite5n1PacketV2': 14.245,
> 'model.042A.Acurite5n1PacketV2': u'Acurite-5n1',
> 'channel.042A.Acurite5n1PacketV2': u'B',
> 'wind_dir.042A.Acurite5n1PacketV2': 112.5,
> 'battery.042A.Acurite5n1PacketV2': 1, 'dateTime': 1590028062,
> 'freq.042A.Acurite5n1PacketV2': None, 'mod.042A.Acurite5n1PacketV2': None,
> 'snr.042A.Acurite5n1PacketV2': None,
> 'sequence_num.042A.Acurite5n1PacketV2': 0, 'noise.042A.Acurite5n1PacketV2':
> None, 'protocol.042A.Acurite5n1PacketV2': None,
> 'rssi.042A.Acurite5n1PacketV2': None, 'msg_type.042A.Acurite5n1PacketV2':
> 49, 'usUnits': 1}
>
>
> I have done a lot of searching on this forum and the web and I understand
> that there have been many changes to the labeling of rain data on the
> Acurite 5n1 system. Howerver I just can't figure out where in the code I
> can make a change that will accept label that my version of the weather
> station uses for rain.
>
>
> I have done a fair share of programming and I have the help of my son who
> is a computer science graduate. I feel quite comfortable messing around in
> the code
>
>
> So far the only change in code that I have tried was to change the line in
> sdr.py
>
>
> I am running rtl_433 version 20.02-55-gc1d1f9f branch master at
> 202005162227
>
>
> thanks for your help
>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/ad940d8b-d4a6-4624-9fc9-a1bd2c0ba17c%40googlegroups.com.
