After I run CSIT with 2 physical cores and 2 worker-threads, the HW cryptodev is not working:
https://jenkins.fd.io/view/csit/job/csit-vpp-perf-master-all/1178/console Testing is HW is there was successful and it was initialized. Can you please take a look? The only change I did was adding 1 more worker threads. Initialization remains the same and Cryptodev HW was not recognized? Peter Mikus Engineer – Software Cisco Systems Limited From: Peter Mikus -X (pmikus - PANTHEON TECHNOLOGIES at Cisco) Sent: Monday, March 13, 2017 2:19 PM To: 'Sergio Gonzalez Monroy' <sergio.gonzalez.mon...@intel.com>; Maciek Konstantynowicz (mkonstan) <mkons...@cisco.com>; Rybalchenko, Kirill <kirill.rybalche...@intel.com>; Nicolau, Radu <radu.nico...@intel.com> Cc: Tibor Frank -X (tifrank - PANTHEON TECHNOLOGIES at Cisco) <tifr...@cisco.com>; csit-...@lists.fd.io; vpp-dev <vpp-dev@lists.fd.io> Subject: RE: IPsec Multi-Tunnel performance test suite failure + Looping @csit-dev @vpp-dev I will add 2 workers/threads that is not a problem. To avoid possible exploding of number of test, we should pick only the representative one. Apart from implementation are there any other differences between tunnel and interface mode? Thanks. Peter Mikus Engineer – Software Cisco Systems Limited From: Sergio Gonzalez Monroy [mailto:sergio.gonzalez.mon...@intel.com] Sent: Monday, March 13, 2017 9:58 AM To: Maciek Konstantynowicz (mkonstan) <mkons...@cisco.com<mailto:mkons...@cisco.com>>; Peter Mikus -X (pmikus - PANTHEON TECHNOLOGIES at Cisco) <pmi...@cisco.com<mailto:pmi...@cisco.com>>; Rybalchenko, Kirill <kirill.rybalche...@intel.com<mailto:kirill.rybalche...@intel.com>>; Nicolau, Radu <radu.nico...@intel.com<mailto:radu.nico...@intel.com>> Cc: Tibor Frank -X (tifrank - PANTHEON TECHNOLOGIES at Cisco) <tifr...@cisco.com<mailto:tifr...@cisco.com>> Subject: Re: IPsec Multi-Tunnel performance test suite failure First, thank you to all involved! I reckon those numbers are in the expected range. The current test is single thread with bidirectional traffic. I would definitely like to see tests with 2 workers/threads, one worker for each direction. One of the reasons is that we cannot saturate QAT with a single worker (QAT should be able to do +40Gbps of encryption). Would it make sense to have another set of tests with 2 workers or just update the current tests to use 2 workers? Regarding the difference between ipsec interface and tunnels (a.k.a. SPD), the results are expected. Basically, it is all about the SPD (Security Policy Database) implementation. The "tunnels" tests use the SPD, whereas the ipsec interfaces do not. The current SPD implementation in VPP follows the guidelines of the RFC, but it does not scale. The ipsec interfaces do not use the SPD at all and a single entry in the fib is all we need to "select" the traffic to encrypt. They effectively are different graph node paths, and even though both end up taking the same amount of cycles (at least for decryption), the interfaces scale much better. Sergio On 11/03/2017 18:36, Maciek Konstantynowicz (mkonstan) wrote: Great Peter, thanks for this final push ! Sergio, team - are these the results you expect to see? Why such a difference interfaces vs. tunnels at 1k scale? aes-gcm interfaces 1 tunnel 1k tunnels Mpps Gbps Mpps Gbps 64B 2.5 1.7 2.3 1.5 IMIX 2.4 7.1 2.1 6.4 1518B 2.4 28.9 2.1 26.0 cbc-sha1 interfaces 1 tunnel 1k tunnels Mpps Gbps Mpps Gbps 64B 2.5 1.7 2.3 1.5 IMIX 2.4 7.2 2.1 6.4 1518B 2.4 29.2 2.1 29.2 aes-gcm tunnels 1 tunnel 1k tunnels Mpps Gbps Mpps Gbps 64B 2.4 1.6 0.4 0.2 IMIX 2.4 7.0 0.3 1.0 1518B 2.2 27.8 0.4 4.3 cbc-sha1 tunnels 1 tunnel 1k tunnels Mpps Gbps Mpps Gbps 64B 2.5 1.7 0.4 0.3 IMIX 2.4 7.2 0.3 1.0 1518B 2.4 29.2 0.4 5.0 -Maciek On 11 Mar 2017, at 06:45, Peter Mikus -X (pmikus - PANTHEON TECHNOLOGIES at Cisco) <pmi...@cisco.com<mailto:pmi...@cisco.com>> wrote: IPSEC is now working. PDR and NDR results are same and can be found there: https://jenkins.fd.io/view/csit/job/csit-vpp-perf-master-all/1156/console Plots will be updated to display IPsecHW (seems like wrong xpath eval). I will check on Monday. So far I will run couple more iterations to see the results @Maciek, I think it is about time to populate all TBs with QAT. Can we coordinate? Peter Mikus Engineer – Software Cisco Systems Limited From: Nicolau, Radu [mailto:radu.nico...@intel.com] Sent: Wednesday, March 08, 2017 2:07 PM To: Gonzalez Monroy, Sergio <sergio.gonzalez.mon...@intel.com<mailto:sergio.gonzalez.mon...@intel.com>>; Peter Mikus -X (pmikus - PANTHEON TECHNOLOGIES at Cisco) <pmi...@cisco.com<mailto:pmi...@cisco.com>>; Rybalchenko, Kirill <kirill.rybalche...@intel.com<mailto:kirill.rybalche...@intel.com>> Cc: Tibor Frank -X (tifrank - PANTHEON TECHNOLOGIES at Cisco) <tifr...@cisco.com<mailto:tifr...@cisco.com>>; Maciek Konstantynowicz (mkonstan) <mkons...@cisco.com<mailto:mkons...@cisco.com>> Subject: RE: IPsec Multi-Tunnel performance test suite failure Hi, I submitted a small patch to only bind QAT VFs. https://gerrit.fd.io/r/#/c/5671/ The downside is that the additional check will have to be updated for new devices. Regards, Radu
_______________________________________________ vpp-dev mailing list vpp-dev@lists.fd.io https://lists.fd.io/mailman/listinfo/vpp-dev
