Excellent! Thanks, -daw-
On 02/16/2017 02:43 PM, Damjan Marion (damarion) wrote:
Looks like I was too optimistic when it comes to syscalls i was planning to use. I was not able to get more than 3 Mpps so I switched to standard shared memory. After a bit of tuning, I’m getting following results: broadwell 3.2GHz, TurboBoost disabled: IXIA - XL710-40G - VPP1 - MEMIF - VPP2 - XL710-40G - IXIA Both VPP instances are running single-core. So it is symetrical setup where each VPP is forwarding between physical NIC and MEMIF. With 64B packets, I’m getting 13.6 Mpps aggregate throughput. With 1500B packets, I’m getting around 29Gbps. Good thing with this new setup, both VPPs can be inside un-priviledged containers. New code is in gerrit...On 14 Feb 2017, at 14:21, Damjan Marion (damarion) <damar...@cisco.com> wrote: I got first pings running over new shared memory interface driver. Code [1] is still very fragile, but basic packet forwarding works ... This interface defines master/slave relationship. Some characteristics: - slave can run inside un-privileged containers - master can run inside container, but it requires global PID namespace and PTRACE capability - initial connection is done over the unix socket, so for container networking socket file needs to be mapped into container - slave allocates shared memory for descriptor rings and passes FD to master - slave is ring producer for both tx and rx, it fills rings with either full or empty buffers - master is ring consumer, it reads descriptors and executes memcpy from/to buffer - process_vm_readv, process_vm_writev linux system calls are used for copy of data directly between master and slave VM (it avoids 2nd memcpy) - process_vm_* system calls are executed once per vector of packets - from security perspective, slave doesn’t have access to master memory - currently polling-only - reconnection should just work - slave runs reconnect process in case when master disappears TODO: - multi-queue - interrupt mode (likely simple byte read/write to file descriptor) - lightweight library to be used for non-VPP clients - L3 mode ??? - perf tuning - user-mode memcpy - master maps slave buffer memory directly… - docs / specification At this point I would really like to hear feedback from people, specially from the usability side. config is basically: create memif socket /path/to/unix_socket.file [master|slave] set int state memif0 up DBGvpp# show interfaces Name Idx State Counter Count local0 0 down memif0 1 up DBGvpp# show interfaces address local0 (dn): memif0 (up): 172.16.0.2/24 DBGvpp# ping 172.16.0.1 64 bytes from 172.16.0.1: icmp_seq=1 ttl=64 time=18.4961 ms 64 bytes from 172.16.0.1: icmp_seq=2 ttl=64 time=18.4282 ms 64 bytes from 172.16.0.1: icmp_seq=3 ttl=64 time=26.4333 ms 64 bytes from 172.16.0.1: icmp_seq=4 ttl=64 time=18.4255 ms 64 bytes from 172.16.0.1: icmp_seq=5 ttl=64 time=14.4133 ms Statistics: 5 sent, 5 received, 0% packet loss DBGvpp# show interfaces Name Idx State Counter Count local0 0 down memif0 1 up rx packets 5 rx bytes 490 tx packets 5 tx bytes 490 drops 5 ip4 5 [1] https://gerrit.fd.io/r/#/c/5004/ _______________________________________________ vpp-dev mailing list vpp-dev@lists.fd.io https://lists.fd.io/mailman/listinfo/vpp-dev_______________________________________________ vpp-dev mailing list vpp-dev@lists.fd.io https://lists.fd.io/mailman/listinfo/vpp-dev
_______________________________________________ vpp-dev mailing list vpp-dev@lists.fd.io https://lists.fd.io/mailman/listinfo/vpp-dev
