Hey everyone, I use Proxmox to manage my VMs, and one of the VMs requires a passed-through HBA. Up until today I've been using Proxmox 3.4 with kernel 2.6.32, which did not use VFIO for passthrough. This set-up worked fine using an IBM M1015 (SAS2008) flashed to 9211-8i IT mode, so the card isn't faulty and is possible to be passed through. Today I updated to the latest version of Proxmox where passthrough is always done via VFIO as far as I can tell.
However, with VFIO it is not possible to pass through this card. A dummy command for pass-through returns: # qemu-system-x86_64 -enable-kvm -m 10G -net none -monitor stdio -serial > none -parallel none -vnc :1 -device vfio-pci,host=1:00.0 -S > QEMU 2.9.1 monitor - type 'help' for more information > (qemu) c > (qemu) qemu-system-x86_64: VFIO_MAP_DMA: -14 > qemu-system-x86_64: vfio_dma_map(0x7f548f0a1fc0, 0xfebd0000, 0x2000, > 0x7f54a909d000) = -14 (Bad address) > qemu: hardware error: vfio: DMA mapping failed, unable to continue > CPU #0: > EAX=00000103 EBX=80001804 ECX=00000103 EDX=00000cfc > ESI=00001800 EDI=00000000 EBP=bffab6b0 ESP=00006d34 > EIP=000eda90 EFL=00000046 [---Z-P-] CPL=0 II=0 A20=1 SMM=0 HLT=0 > ES =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] > CS =0008 00000000 ffffffff 00c09b00 DPL=0 CS32 [-RA] > SS =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] > DS =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] > FS =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] > GS =0010 00000000 ffffffff 00c09300 DPL=0 DS [-WA] > LDT=0000 00000000 0000ffff 00008200 DPL=0 LDT > TR =0000 00000000 0000ffff 00008b00 DPL=0 TSS32-busy > GDT= 000f7070 00000037 > IDT= 000f70ae 00000000 > CR0=00000011 CR2=00000000 CR3=00000000 CR4=00000000 > DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 > DR3=0000000000000000 > DR6=00000000ffff0ff0 DR7=0000000000000400 > EFER=0000000000000000 > FCW=037f FSW=0000 [ST=0] FTW=00 MXCSR=00001f80 > FPR0=0000000000000000 0000 FPR1=0000000000000000 0000 > FPR2=0000000000000000 0000 FPR3=0000000000000000 0000 > FPR4=0000000000000000 0000 FPR5=0000000000000000 0000 > FPR6=0000000000000000 0000 FPR7=0000000000000000 0000 > XMM00=00000000000000000000000000000000 > XMM01=00000000000000000000000000000000 > XMM02=00000000000000000000000000000000 > XMM03=00000000000000000000000000000000 > XMM04=00000000000000000000000000000000 > XMM05=00000000000000000000000000000000 > XMM06=00000000000000000000000000000000 > XMM07=00000000000000000000000000000000 > Aborted > This has been previously reported on this mailing list ( https://www.redhat.com/archives/vfio-users/2016-May/msg00054.html), but no solution was found for the poster. It seems that on Fedora this passthrough works fine ( https://www.redhat.com/archives/vfio-users/2016-May/msg00246.html), but in Ubuntu and Proxmox (also Debian-based), it doesn't. Other cards, such as the 9207-8i (SAS2308 chip) also seem to work ( https://forum.proxmox.com/threads/promxox4-4-qm-status-stopped-for-passthrough-of-ibm1015.32841/#post-169018 ). Any ideas on how to get this card working? I'd be grateful for any input, and I'm not alone in this combination of hardware. For completeness: root@pve:~# uname -a Linux pve 4.13.4-1-pve #1 SMP PVE 4.13.4-26 (Mon, 6 Nov 2017 11:23:55 +0100) x86_64 GNU/Linux and 01:00.0 Serial Attached SCSI controller [0107]: LSI Logic / Symbios Logic SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] [1000:0072] (rev 03) Subsystem: LSI Logic / Symbios Logic SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] [1000:3020] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at e000 [disabled] [size=256] Region 1: Memory at df6c0000 (64-bit, non-prefetchable) [disabled] [size=16K] Region 3: Memory at df280000 (64-bit, non-prefetchable) [disabled] [size=256K] Expansion ROM at df200000 [disabled] [size=512K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D3 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Exit Latency L0s <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range BC, TimeoutDis+, LTR-, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [d0] Vital Product Data pcilib: sysfs_read_vpd: read failed: Input/output error Not readable Capabilities: [a8] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [c0] MSI-X: Enable- Count=15 Masked- Vector table: BAR=1 offset=00002000 PBA: BAR=1 offset=00003800 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [138 v1] Power Budgeting <?> Capabilities: [150 v1] Single Root I/O Virtualization (SR-IOV) IOVCap: Migration-, Interrupt Message Number: 000 IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy- IOVSta: Migration- Initial VFs: 16, Total VFs: 16, Number of VFs: 0, Function Dependency Link: 00 VF offset: 1, stride: 1, Device ID: 0072 Supported Page Size: 00000553, System Page Size: 00000001 Region 0: Memory at 00000000df6c4000 (64-bit, non-prefetchable) Region 2: Memory at 00000000df2c0000 (64-bit, non-prefetchable) VF Migration: offset: 00000000, BIR: 0 Capabilities: [190 v1] Alternative Routing-ID Interpretation (ARI) ARICap: MFVC- ACS-, Next Function: 0 ARICtl: MFVC- ACS-, Function Group: 0 Kernel driver in use: vfio-pci Kernel modules: mpt3sas
_______________________________________________ vfio-users mailing list vfio-users@redhat.com https://www.redhat.com/mailman/listinfo/vfio-users