Hello Klaus,
Am 08.11.24 um 04:35 schrieb schorpp:
Am 07.11.24 um 21:36 schrieb Klaus Schmidinger:
On 06.11.24 04:57, schorpp wrote:
Hello,
I've build a new VDR with h.264 xineliboutput plugin software decoding
and got a problem now with
buffer overruns and distorted recordings on all HD channels:
...
Nov 5 05:32:03 vdr2 vdr: [32753] ERROR: 47231 ring buffer overflows (8879240
bytes dropped)
Nov 5 05:32:09 vdr2 vdr: [32753] ERROR: 31042 ring buffer overflows (5835896
bytes dropped)
Nov 5 05:32:15 vdr2 vdr: [32753] ERROR: 47325 ring buffer overflows (8897100
bytes dropped)
Nov 5 05:32:21 vdr2 vdr: [32753] ERROR: 28306 ring buffer overflows (5321528
bytes dropped)
Nov 5 05:32:27 vdr2 vdr: [32753] ERROR: 14033 ring buffer overflows (2638204
bytes dropped)
...
This occurs with both saa7146 and mantis pci tuner cards.
This has not occured with the old VDR system using Broadcomm's crystalhd
decoder in libxine.
I've FIXED it.
Not yet. It occurs again after some days system uptime.
Nov 9 18:25:33 vdr2 vdr: [5318] buffer stats: 178600 (3%) used
Nov 9 18:25:33 vdr2 vdr: [5337] TS buffer on device 1 thread started
(pid=4621, tid=5337, prio=high)
Nov 9 20:12:00 vdr2 vdr: [8367] TS buffer on device 2 thread started
(pid=4621, tid=8367, prio=high)
Nov 9 21:57:57 vdr2 vdr: [11332] TS buffer on device 3 thread started
(pid=4621, tid=11332, prio=high)
Nov 9 23:13:00 vdr2 vdr: [5337] TS buffer on device 1 thread ended (pid=4621,
tid=5337)
Nov 9 23:13:00 vdr2 vdr: [5335] buffer stats: 500268 (9%) used
Nov 9 23:13:00 vdr2 vdr: [13456] TS buffer on device 1 thread started
(pid=4621, tid=13456, prio=high)
Nov 9 23:13:01 vdr2 vdr: [4621] buffer stats: 0 (0%) used
Nov 9 23:30:00 vdr2 vdr: [4621] buffer stats: 222968 (1%) used
Nov 9 23:37:52 vdr2 vdr: [4621] buffer stats: 474136 (2%) used
Nov 9 23:37:52 vdr2 vdr: [11332] TS buffer on device 3 thread ended (pid=4621,
tid=11332)
Nov 9 23:37:52 vdr2 vdr: [11331] buffer stats: 233872 (11%) used
Nov 9 23:37:53 vdr2 vdr: [14185] TS buffer on device 3 thread started
(pid=4621, tid=14185, prio=high)
Nov 10 00:37:14 vdr2 vdr: [4621] buffer stats: 0 (0%) used
Cause was HW unsupported pci hotplug damaged motherboard pci bridge and/or
removed antenna signal amplififier.
No. dd write speed test showed a regression in the 3.12.40 AHCI SATA
driver, HDD write performance dropped down from 60MB/s to 4MB/s on the
which is too slow for HDTV or multiple recordings.
After reboot full speed is back. I've upgraded the kernel to the last
longterm 4.19.324 stable version to check if this resolves the issue or
it is a hardware issue of the
# lspci -vvv -s 00:1f.2
00:1f.2 SATA controller: Intel Corporation 7 Series/C210 Series Chipset
Family 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 7 Series/C210 Series Chipset Family 6-port
SATA Controller [AHCI mode]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 32
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7e36000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee08004 Data: 4022
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
SATA HBA or WDC Drive Firmware.
y
tom
