Sam: Yes, updating to the recently released UHD 3.15.0.0 resolved this issue.
Thank you Subu On Fri, Jan 3, 2020 at 8:07 PM Sam Reiter <sam.rei...@ettus.com> wrote: > Hey Subu, > > I'd suspect that the MPM versioning is the issue here. You can manually > compile and install MPM on your E320, or you can simply reflash your SD > card with the latest SDimg. Based on when this was posted vs when v3.15.0.0 > was tagged, I'd guess you're working with a release candidate and didn't > have access to a fresh filesystem image to install. You'll want to install > v3.15.0.0 on your host first, then follow this guide for the mender update: > > https://kb.ettus.com/E320_Getting_Started_Guide#Mender_Update_Process > > Or this guide for reflashing the SD card by physically inserting it into > your PC (you need to take the backplate off the E320 to access the SD): > > https://kb.ettus.com/Writing_the_USRP_File_System_Disk_Image_to_a_SD_Card > > Sam Reiter > Ettus Research > > On Tue, Dec 24, 2019 at 12:15 PM Subu Rama via USRP-users < > usrp-users@lists.ettus.com> wrote: > >> I am going to run my USRP E320 in host mode. To make sure that the FPGA >> images on my development host and E320 match, I am trying to upload 1G FPGA >> image to the E320. >> >> The following is the process I am following: >> >> Network interfaces on the E320: >> >> root@ni-e320-31BB638:~# ip a >> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1000 >> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 >> inet 127.0.0.1/8 scope host lo >> valid_lft forever preferred_lft forever >> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen >> 1000 >> link/ether 00:80:2f:28:8d:7e brd ff:ff:ff:ff:ff:ff >> inet 192.168.1.2/24 brd 192.168.1.255 scope global eth0 >> valid_lft forever preferred_lft forever >> 3: sfp0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen >> 1000 >> link/ether 00:80:2f:28:8d:7f brd ff:ff:ff:ff:ff:ff >> inet 192.168.10.2/24 brd 192.168.10.255 scope global sfp0 >> valid_lft forever preferred_lft forever >> >> -------------------------------------------------------------- >> Trying to upload the 1G image to the E320: >> >> gnuradio@nuc-qrc3 (UHD-3.15.LTS):/usr/local/src/uhd/fpga-src >> >> uhd_image_loader --args >> "type=e3xx,product=e320,mgmt_addr=192.168.1.2,fpga=1G" >> [INFO] [UHD] linux; GNU C++ version 9.2.1 20191008; Boost_107100; >> UHD_3.15.0.0-0-g4e06022c >> [INFO] [MPMD] Initializing 1 device(s) in parallel with args: >> mgmt_addr=192.168.1.2,type=e3xx,product=e320,serial=31BB638,claimed=False,skip_init=1 >> [INFO] [MPMD] Claimed device without full initialization. >> [INFO] [MPMD IMAGE LOADER] Starting update. This may take a while. >> [INFO] [MPM.PeriphManager] Updating component `fpga' >> [INFO] [MPM.PeriphManager] Updating component `dts' >> [ERROR] [MPM.PeriphManager] Error executing `dtc': Command '['dtc', >> '--symbols', '-O', 'dtb', '-q', '-o', '/lib/firmware/e320.dtbo', >> '/lib/firmware/e320.dts']' returned non-zero exit status 1 >> [INFO] [MPM.RPCServer] Resetting peripheral manager. >> [INFO] [MPM.PeriphManager] Device serial number: 31BB638 >> [INFO] [MPMD IMAGE LOADER] Update component function succeeded. >> [INFO] [MPM.PeriphManager] Found 1 daughterboard(s). >> [WARNING] [MPM.PeriphManager] Actual minor compat ahead of expected >> compat for component `FPGA'. Expected: 3.0 Actual: 3.1 >> >> ----------------------- >> Result of a probe: >> >> gnuradio@nuc-qrc3 (UHD-3.15.LTS):/usr/local/src/uhd/fpga-src >> >> uhd_usrp_probe --args "addr=192.168.10.2" >> [INFO] [UHD] linux; GNU C++ version 9.2.1 20191008; Boost_107100; >> UHD_3.15.0.0-0-g4e06022c >> [INFO] [MPMD] Initializing 1 device(s) in parallel with args: >> mgmt_addr=192.168.10.2,type=e3xx,product=e320,serial=31BB638,claimed=False,addr=192.168.10.2 >> [INFO] [MPM.main] Launching USRP/MPM, version: 3.13.0.2-gunknown >> [INFO] [MPM.main] Spawning RPC process... >> [INFO] [MPM.PeriphManager] Device serial number: 31BB638 >> [INFO] [MPM.PeriphManager] Found 1 daughterboard(s). >> [WARNING] [MPM.PeriphManager] Actual minor compat ahead of expected >> compat for component `FPGA'. Expected: 3.0 Actual: 3.1 >> [INFO] [MPM.RPCServer] RPC server ready! >> [INFO] [MPM.RPCServer] Spawning watchdog task... >> [WARNING] [MPMD] Could not determine link speed; using 1GibE max speed of >> 1.25e+08 >> [WARNING] [MPMD] Could not determine link speed; using 1GibE max speed of >> 1.25e+08 >> [INFO] [0/DmaFIFO_0] Initializing block control (NOC ID: >> 0xF1F0D00000000000) >> [INFO] [MPM.PeriphManager] init() called with device args >> `product=e320,mgmt_addr=192.168.10.2'. >> [INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1329 MB/s) >> [INFO] [0/DmaFIFO_0] BIST passed (Throughput: 1336 MB/s) >> [WARNING] [MPMD] Could not determine link speed; using 1GibE max speed of >> 1.25e+08 >> [WARNING] [MPMD] Could not determine link speed; using 1GibE max speed of >> 1.25e+08 >> [INFO] [0/Radio_0] Initializing block control (NOC ID: 0x12AD100000003320) >> [WARNING] [MPMD] Could not determine link speed; using 1GibE max speed of >> 1.25e+08 >> [WARNING] [MPMD] Could not determine link speed; using 1GibE max speed of >> 1.25e+08 >> [INFO] [0/DDC_0] Initializing block control (NOC ID: 0xDDC0000000000000) >> [WARNING] [MPMD] Could not determine link speed; using 1GibE max speed of >> 1.25e+08 >> [WARNING] [MPMD] Could not determine link speed; using 1GibE max speed of >> 1.25e+08 >> [INFO] [0/DUC_0] Initializing block control (NOC ID: 0xD0C0000000000002) >> [ERROR] [UHD] Exception caught in safe-call. >> in uhd::mpmd::mpmd_mboard_impl::~mpmd_mboard_impl() >> at /usr/local/src/uhd/host/lib/usrp/mpmd/mpmd_mboard_impl.cpp:308 >> dump_logs(); _claimer_task.reset(); _xport_mgr.reset(); if (not >> rpc->request_with_token<bool>("unclaim")) { >> uhd::_log::log(uhd::log::warning, >> "/usr/local/src/uhd/host/lib/usrp/mpmd/mpmd_mboard_impl.cpp", 310, "MPMD", >> boost::this_thread::get_id()) << "Failure to ack unclaim!";; } -> >> rpc::timeout: Timeout of 2000ms while calling RPC function 'unclaim' >> Error: rpc::timeout: Timeout of 60000ms while calling RPC function >> 'db_0_catalina_tune' >> ..... >> >> See that this still shows USRP 3.13 version: >> >> [INFO] [MPM.main] Launching USRP/MPM, version: 3.13.0.2-gunknown >> >> So, how do I get the uhd_image_loader command to run successfully to get >> the 3.15 version on the E320? >> >> Thank you >> Subu >> >> >> >> _______________________________________________ >> USRP-users mailing list >> USRP-users@lists.ettus.com >> http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com >> >
_______________________________________________ USRP-users mailing list USRP-users@lists.ettus.com http://lists.ettus.com/mailman/listinfo/usrp-users_lists.ettus.com
