Hi Misak, I do not think we will be supporting any in the near future. Enabling gfapi means that access mechanism of drive changes and i think we will need to stop the vms.
Thanks kasturi On Wed, Nov 15, 2017 at 12:27 PM, Misak Khachatryan <[email protected]> wrote: > Hi, > > will it be a more clean approach? I can't tolerate full stop of all > VMs just to enable it, seems too disastrous for real production > environment. Will it be some migration mechanisms in future? > > Best regards, > Misak Khachatryan > > > On Fri, Nov 10, 2017 at 12:35 AM, Darrell Budic <[email protected]> > wrote: > > You do need to stop the VMs and restart them, not just issue a reboot. I > > havn’t tried under 4.2 yet, but it works in 4.1.6 that way for me. > > > > ________________________________ > > From: Alessandro De Salvo <[email protected]> > > Subject: Re: [ovirt-users] Enabling libgfapi disk access with oVirt 4.2 > > Date: November 9, 2017 at 2:35:01 AM CST > > To: [email protected] > > > > > > Hi again, > > > > OK, tried to stop all the vms, except the engine, set engine-config -s > > LibgfApiSupported=true (for 4.2 only) and restarted the engine. > > > > When I tried restarting the VMs they are still not using gfapi, so it > does > > not seem to help. > > > > Cheers, > > > > > > Alessandro > > > > > > > > Il 09/11/17 09:12, Alessandro De Salvo ha scritto: > > > > Hi, > > where should I enable gfapi via the UI? > > The only command I tried was engine-config -s LibgfApiSupported=true but > the > > result is what is shown in my output below, so it’s set to true for > v4.2. Is > > it enough? > > I’ll try restarting the engine. Is it really needed to stop all the VMs > and > > restart them all? Of course this is a test setup and I can do it, but for > > production clusters in the future it may be a problem. > > Thanks, > > > > Alessandro > > > > Il giorno 09 nov 2017, alle ore 07:23, Kasturi Narra <[email protected]> > ha > > scritto: > > > > Hi , > > > > The procedure to enable gfapi is below. > > > > 1) stop all the vms running > > 2) Enable gfapi via UI or using engine-config command > > 3) Restart ovirt-engine service > > 4) start the vms. > > > > Hope you have not missed any !! > > > > Thanks > > kasturi > > > > On Wed, Nov 8, 2017 at 11:58 PM, Alessandro De Salvo > > <[email protected]> wrote: > >> > >> Hi, > >> > >> I'm using the latest 4.2 beta release and want to try the gfapi access, > >> but I'm currently failing to use it. > >> > >> My test setup has an external glusterfs cluster v3.12, not managed by > >> oVirt. > >> > >> The compatibility flag is correctly showing gfapi should be enabled with > >> 4.2: > >> > >> # engine-config -g LibgfApiSupported > >> LibgfApiSupported: false version: 3.6 > >> LibgfApiSupported: false version: 4.0 > >> LibgfApiSupported: false version: 4.1 > >> LibgfApiSupported: true version: 4.2 > >> > >> The data center and cluster have the 4.2 compatibility flags as well. > >> > >> However, when starting a VM with a disk on gluster I can still see the > >> disk is mounted via fuse. > >> > >> Any clue of what I'm still missing? > >> > >> Thanks, > >> > >> > >> Alessandro > >> > >> _______________________________________________ > >> Users mailing list > >> [email protected] > >> http://lists.ovirt.org/mailman/listinfo/users > > > > > > > > > > _______________________________________________ > > Users mailing list > > [email protected] > > http://lists.ovirt.org/mailman/listinfo/users > > > > > > _______________________________________________ > > Users mailing list > > [email protected] > > http://lists.ovirt.org/mailman/listinfo/users > > > > > > > > _______________________________________________ > > Users mailing list > > [email protected] > > http://lists.ovirt.org/mailman/listinfo/users > > > _______________________________________________ > Users mailing list > [email protected] > http://lists.ovirt.org/mailman/listinfo/users >
_______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
