Hi Fabian, I think the bad route is a link local route 169.254.0.0/16. I am not quite sure if it's a real bug but in my case I have to remove this route. Also I am using ramdisk based node without a local disk. Can anything be persisted?
David ----- Original Message ----- > From: Fabian Deutsch <[email protected]> > To: David Li <[email protected]> > Cc: "[email protected]" <[email protected]> > Sent: Wednesday, December 4, 2013 11:17 AM > Subject: Re: [Users] How to pxeboot ovrit node into memory automatically? > > Am Montag, den 02.12.2013, 13:53 -0800 schrieb David Li: >> Hi Fabian, >> >> Everytime the ovirt node boots up, it adds a route entry that I have to > manually remove. Otherwise it messed up my routing. >> How do I modify the boot scripts to automatically remove it? > > Hey David, > > could you file a bug for that route problem? > > You can try the following workaround: > > # Create /etc/rc.d/rc.local with the commands to run > $ vi /etc/rc.d/rc.local > $ chmod a+x /etc/rc.d/rc.local > $ persist /etc/rc.d/rc.local > > /etc/rc.d/rc.local should then be run on every boot. > > - fabian > >> ----- Original Message ----- >> > From: Fabian Deutsch <[email protected]> >> > To: David Li <[email protected]> >> > Cc: "[email protected]" <[email protected]> >> > Sent: Monday, October 28, 2013 7:45 AM >> > Subject: Re: [Users] How to pxeboot ovrit node into memory > automatically? >> > >> > Am Montag, den 28.10.2013, 07:42 -0700 schrieb David Li: >> >> >> >> Hi Fabian, >> >> >> >> Yes rootpwd worked too! Thanks. >> >> >> >> Two new problems: >> >> >> >> But I found there is no networking for the stateless node. >> >> What kernel boot options are used to either use DHCP or > statically >> > configure the IP address for an interface on the node? >> >> >> >> I also need to have the sshd enabled. Is there a kernel option > for that? >> > >> > Hey David, >> > >> > here you can find all the supported boot params in ovirt node: >> > > http://gerrit.ovirt.org/gitweb?p=ovirt-node.git;a=blob;f=scripts/ovirt-init-functions.sh.in;h=c4280caefb89c77afc1e8bec8c925aa7f3039733;hb=HEAD#l214 >> > >> > Greetings >> > fabian >> > >> >> David >> >> >> >> >> >> >> >> ----- Original Message ----- >> >> > From: Fabian Deutsch <[email protected]> >> >> > To: David Li <[email protected]> >> >> > Cc: "[email protected]" <[email protected]> >> >> > Sent: Friday, October 25, 2013 9:10 AM >> >> > Subject: Re: [Users] How to pxeboot ovrit node into memory >> > automatically? >> >> > >> >> > Am Freitag, den 25.10.2013, 08:57 -0700 schrieb David Li: >> >> >> Hi Fabian, >> >> >> >> >> >> That kernel option worked for me! The node is booted > up in RAM. >> > Thanks! >> >> >> >> >> >> My next question is: >> >> >> How do I specify the root login and passwd as boot > parameters? >> >> > >> >> > Hey David. >> >> > >> >> > Nice that it worked! Were you able to register to the > Engine? >> >> > >> >> > You can use the adminpw= and rootpw= kernel arguments to set > >> > passwords. >> >> > use >> >> > $ openssl passwd -salt 42 >> >> > to create one or two passwords >> >> > >> >> > Greetings >> >> > fabian >> >> > >> >> >> David >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> ----- Original Message ----- >> >> >> > From: Fabian Deutsch <[email protected]> >> >> >> > To: David Li <[email protected]> >> >> >> > Cc: "[email protected]" > <[email protected]> >> >> >> > Sent: Thursday, October 24, 2013 11:47 PM >> >> >> > Subject: Re: [Users] How to pxeboot ovrit node > into memory >> >> > automatically? >> >> >> > >> >> >> > Am Donnerstag, den 24.10.2013, 16:26 -0700 schrieb > David Li: >> >> >> >> Hi, >> >> >> >> >> >> >> >> I was following the instructions at >> >> > http://www.ovirt.org/Node_PXE. My goal >> >> >> > is to use pxeboot (iPXE) to boot the node entirely > into RAM >> > with >> >> > rootfs. What I >> >> >> > got now is an installation screen which requires a > local >> > storage. My >> >> > system has >> >> >> > no disk and this doesn't quite work for me. >> >> >> >> >> >> >> >> What's are the kernel parameters I need > to use to >> > boot the >> >> > node into >> >> >> > RAM automatically? I am OK as the first step with > a >> > stateless node. >> >> >> > >> >> >> > Hey David, >> >> >> > >> >> >> > the stateless mode is currently not completely > working with >> > oVirt >> >> >> > Engine. That means a Node needs to be approved > each time it >> > boots into >> >> >> > the stateless mode. >> >> >> > The stateless mode can be entered by appending > stateless to >> > the >> >> > default >> >> >> > kernel arguments. >> >> >> > >> >> >> > Greetings >> >> >> > fabian >> >> >> > >> >> > >> > > _______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
