RE: build in wronge state

[Jonathan Tilley]

Hi,   I have tried 1)forced a build 2)restart Contiunnm 3) Reboot server, but still Continuum thinks the build is alive.   “Jun 8, 2006 3:00:04 PM Started since : 19 h 27 min 35 sec Result”     3 Jun 9, 2006 10:00:04 AM Jun 9, 2006 10:02:58 AM Duration : 2 min 54 sec Result 2 Jun 9, 2006 8:23:19 AM Jun 9, 2006 8:25:53 AM Duration : 2 min 34 sec Result Jun 8, 2006 4:08:03 PM Jun 8, 2006 4:09:10 PM Duration : 1 min 7 sec Result Jun 8, 2006 4:00:02 PM Jun 8, 2006 4:07:34 PM Duration : 7 min 32 sec Result Jun 8, 2006 3:00:04 PM Started since : 19 h 27 min 35 sec Result     My thinking is that there must be entries in the Derby database that can be changed to tell Continuum that a build has completed. The problem is how to do it.   Cheers   Jonathan     -----Original Message----- From: Emmanuel Venisse [mailto:[EMAIL PROTECTED] Sent: 09 June 2006 10:03 To: continuum-users@maven.apache.org Subject: Re: build in wronge state   Try to force a new build. If it doesn't work, restart your Continuum.   Emmanuel   Jonathan Tilley a écrit : > Hi, > >  > > I have a build that has completed in failure, but Continuum still thinks > that the build is running. > >  > > The tail of the build logs is > >  > > [surefire] Tests run: 1, Failures: 0, Errors: 0, Time elapsed: 0 sec > > [INFO] ------------------------------------------------------------------------ > > [ERROR] BUILD ERROR > > [INFO] ------------------------------------------------------------------------ > > [INFO] There are test failures. > > [INFO] ------------------------------------------------------------------------ > > [INFO] For more information, run Maven with the -e switch > > [INFO] ------------------------------------------------------------------------ > > [INFO] Total time: 4 minutes 49 seconds > > [INFO] Finished at: Thu Jun 08 15:04:55 BST 2006 > > [INFO] Final Memory: 27M/63M > > [INFO] ------------------------------------------------------------------------ > > errorcode after mvn clean install is ... > > 1 > > starting postExec... > >  > >  > >  > > But Continuum doesn’t recognise that the build has completed > > The build results says > >  > > Start Time Jun 8, 2006 3:00:04 PM > > End Time Duration Started since : 17 h 48 min 41 sec > > Build Trigger Scheduled State BuildingBuild# > >  > >  > > My question is how can one manually kill a build or tell Continuum that the build > > has completed. > >  > > Cheers > >  > > Jonathan > >  > >  > >  > >  > > This transmission is confidential and intended solely for the person or > organisation to whom it is addressed. It may contain privileged and > confidential information. If you are not the intended recipient, you > should not copy, distribute or take any action in reliance on it. If you > have received this transmission in error, please notify the sender > immediately. Any opinions or advice contained in this e-mail are those > of the individual sender except where they are stated to be the views of > RDF Group plc. All messages passing through this gateway are virus scanned. >   This transmission is confidential and intended solely for the person or organisation to whom it is addressed. It may contain privileged and confidential information. If you are not the intended recipient, you should not copy, distribute or take any action in reliance on it. If you have received this transmission in error, please notify the sender immediately. Any opinions or advice contained in this e-mail are those of the individual sender except where they are stated to be the views of RDF Group plc. All messages passing through this gateway are virus scanned.