It worked. Thank you very much for your help ! :)
2014-04-03 11:03 GMT+02:00 James Dobson <jdob...@velocix.com>: > You need to upgrade the version of libvirt, basically support for > openvswitch wasn't added until a later version if you don't have the later > version you have to use brcompat. > > > > http://libvirt.org/formatnetwork.html > > > > bridge > > This network describes either 1) an existing host bridge that was > configured outside of libvirt (if a <bridge name='xyz'/> element has been > specified, Since 0.9.4), 2) an existing Open vSwitch bridge that was > configured outside of libvirt (if both a <bridge name='xyz'/> element > *and* a <virtualport type='openvswitch'/> have been specified Since > 0.10.0) 3) an interface or group of interfaces to be used for a "direct" > connection via macvtap using macvtap's "bridge" mode (if the forward > element has one or more <interface> subelements, Since 0.9.4) (see Direct > attachment to physical > interface<http://libvirt.org/formatdomain.html#elementsNICSDirect>for > descriptions of the various macvtap modes). libvirt doesn't attempt to > manage the bridge interface at all, thus the <bridge> element's stp and > delay attributes are not allowed; no iptables rules, IP addresses, or > DHCP/DNS services are added; at the IP level, the guest interface appears > to be directly connected to the physical interface.Since 0.9.4 > > > > This also may help.. > > > > > http://blog.scottlowe.org/2012/11/05/compiling-libvirt-1-0-0-on-ubuntu-12-04-and-12-10/ > > > > I was lucky that in centos 6 the epel repository had a later version I > could use. > > > > HTH, > > > > James > > > > *From:* users-boun...@lists.opennebula.org [mailto: > users-boun...@lists.opennebula.org] *On Behalf Of *Leszek Master > *Sent:* 03 April 2014 09:40 > *To:* Stefan Kooman; Users OpenNebula > *Subject:* Re: [one-users] Opennebula and openvswitch problem. > > > > I'm waiting for official relese of next LTS version, i can use only LTS in > my production, so i was testing it on the 12.04. If there isn't any > official manual how ot solve this problem i'll upgrade my distro and try > then :) Thanks for your help. > > > > 2014-04-03 9:25 GMT+02:00 Stefan Kooman <ste...@bit.nl>: > > Quoting Leszek Master (keks...@gmail.com): > > Still the same problem: > > > > failed: error: Unable to add bridge br0 port vnet0: Operation not > supported > > > > sudo ovs-vsctl show > > e2e80002-00ea-464d-9c62-5af5e0889d81 > > Bridge "br0" > > Port "eth1" > > Interface "eth1" > > Port "br0" > > Interface "br0" > > type: internal > > ovs_version: "1.4.6" > > leni@node-03:~$ sudo brctl show > > bridge name bridge id STP enabled interfaces > > leni@node-03:~$ > > > > > > Tryied updating openvswitch from 1.4 to 1.9, the problem stays the same. > > The only thing to get this working for now is to load brcompat module to > > os, but it's problematic with new nodes. Any one have solution to this > > problem? > > I believe I managed to get it going on Precise, but I had some issues, > just like you. It's been some time ago though. Ubuntu Precise Trusty > Tahr is due in a few weeks. Any particular reason you would want to stay > on Precise?. > > > Gr. Stefan > > -- > | BIT BV http://www.bit.nl/ Kamer van Koophandel 09090351 > | GPG: 0xD14839C6 +31 318 648 688 / i...@bit.nl > > >
_______________________________________________ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org
