I suspect that something is wrong with your Intel C++ compiler installation, but you can simply avoid the issue if you add --disable-vt to Open MPI's ./configure command line. This will skip building the (optional) Vampir Trace package, which is where you are running into this problem (VT is written in C++; the vast majority of the rest of Open MPI is written in C).
On Sep 22, 2013, at 10:40 AM, Syed Ahsan Ali <ahsansha...@gmail.com> wrote: > Its ok Jeff. > I am not sure about other C++ codes and STL with icpc because it never > happened and I don't know anything about STL.(pardon my less > knowledge). What do you suggest in this case? installation of > different version of openmpi or intel compilers? or any other > solution. > > On Fri, Sep 20, 2013 at 8:35 PM, Jeff Squyres (jsquyres) > <jsquy...@cisco.com> wrote: >> Sorry for the delay replying -- I actually replied on the original thread >> yesterday, but it got hung up in my outbox and I didn't notice that it >> didn't actually go out until a few moments ago. :-( >> >> I'm *guessing* that this is a problem with your local icpc installation. >> >> Can you compile / run other C++ codes that use the STL with icpc? >> >> >> On Sep 20, 2013, at 6:59 AM, Syed Ahsan Ali <ahsansha...@gmail.com> wrote: >> >>> Output of make V=1 is attached. Again same error. If intel compiler is >>> using C++ headers from gfortran then how can we avoid this. >>> >>> On Fri, Sep 20, 2013 at 11:07 AM, Bert Wesarg >>> <bert.wes...@googlemail.com> wrote: >>>> Hi, >>>> >>>> On Fri, Sep 20, 2013 at 4:49 AM, Syed Ahsan Ali <ahsansha...@gmail.com> >>>> wrote: >>>>> I am trying to compile openmpi-1.6.5 on fc16.x86_64 with icc and ifort >>>>> but getting the subject error. config.out and make.out is attached. >>>>> Following command was used for configure >>>>> >>>>> ./configure CC=icc CXX=icpc FC=ifort F77=ifort F90=ifort >>>>> --prefix=/home/openmpi_gfortran -enable-mpi-f90 --enable-mpi-f77 |& >>>>> tee config.out >>>> >>>> could you also run make with 'make V=1' and send the output. Anyway it >>>> looks like the intel compiler uses the C++ headers from GCC 4.6.3 and >>>> I don't know if this is supported. >>>> >>>> Bert >>>> >>>>> Please help/advise. >>>>> Thank you and best regards >>>>> Ahsan >>>>> >>> >>> >>> >>> -- >>> Syed Ahsan Ali Bokhari >>> Electronic Engineer (EE) >>> >>> Research & Development Division >>> Pakistan Meteorological Department H-8/4, Islamabad. >>> Phone # off +92518358714 >>> Cell # +923155145014 >>> <makeV.zip>_______________________________________________ >>> users mailing list >>> us...@open-mpi.org >>> http://www.open-mpi.org/mailman/listinfo.cgi/users >> >> >> -- >> Jeff Squyres >> jsquy...@cisco.com >> For corporate legal information go to: >> http://www.cisco.com/web/about/doing_business/legal/cri/ >> >> _______________________________________________ >> users mailing list >> us...@open-mpi.org >> http://www.open-mpi.org/mailman/listinfo.cgi/users > > > > -- > Syed Ahsan Ali Bokhari > Electronic Engineer (EE) > > Research & Development Division > Pakistan Meteorological Department H-8/4, Islamabad. > Phone # off +92518358714 > Cell # +923155145014 > _______________________________________________ > users mailing list > us...@open-mpi.org > http://www.open-mpi.org/mailman/listinfo.cgi/users -- Jeff Squyres jsquy...@cisco.com For corporate legal information go to: http://www.cisco.com/web/about/doing_business/legal/cri/
