oooh how stupid of me probably my eyes have stopped working from reading the user-guide 2 much on my computer screen.
now i am faced by a new error i get a 3:waiting in queue bcoz VSMSC driver not found what do i do about it I am using kannel for sending and recieving only sms with nokia 6610i and a serial cable my configuration file is: group = smsc smsc = at smsc-id = VSMSC modemtype = auto device = /dev/ttyS1 speed=19200 port = 10000 connect-allow-ip = 127.0.0.1 # SMSBOX SETUP group = smsbox bearerbox-host = 127.0.0.1 sendsms-port = 13013 global-sender = 13013 #sendsms-chars = "0123456789 +-" log-file = "/tmp/smsbox.log" log-level = 1 access-log = "/tmp/access.log" #--------------------------------------------- # SEND-SMS USERS group = sendsms-user username = tester password = foobar #user-deny-ip = "" user-allow-ip = "127.0.0.1" ******************************************************* I have the cable checked it works fine with nokia suite for transferring data. output of wvdialconf is ************************************************************************ [EMAIL PROTECTED]:~/Desktop/gateway-1.4.1/checks$ wvdialconf Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. WvModem<*1>: Cannot set information for serial port. ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. WvModem<*1>: Cannot set information for serial port. ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Modem Port Scan<*1>: S2 S3 S4 S5 S6 S7 S8 S9 Modem Port Scan<*1>: S10 S11 S12 S13 S14 S15 S16 S17 Modem Port Scan<*1>: S18 S19 S20 S21 S22 S23 S24 S25 Modem Port Scan<*1>: S26 S27 S28 S29 S30 S31 S32 S33 Modem Port Scan<*1>: S34 S35 S36 S37 S38 S39 S40 S41 Modem Port Scan<*1>: S42 S43 S44 S45 S46 S47 Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at http://open.nit.ca/wiki/?WvDial If you still have problems, send mail to <[EMAIL PROTECTED]>. **************************************************************** the ouput of setserial command is ************************************************ [EMAIL PROTECTED]:~/Desktop/gateway-1.4.1/checks$ setserial /dev/ttyS1 /dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3 I am clueless regarding how 2 go about this problem plz help -- View this message in context: http://www.nabble.com/error-codes-tf3361861.html#a9370846 Sent from the Kannel - User mailing list archive at Nabble.com.
