Thank you for your help
Do I need to specify what port the vlan are going to use?
1.- create vlnasconf tvlan 65,300-800end
2.- conf tswitchport mode trunkswitchport trunk encapsulation dot1q switchport
trunk allowed vlan 65,300-800end
From: Sateesh Chodapuneedi <[email protected]>
To: "[email protected]" <[email protected]>; Luis
<[email protected]>
Cc: Paul Angus <[email protected]>
Sent: Friday, September 8, 2017 9:42 AM
Subject: Re: Configuring CS with Advance Networking for an internal laboratory
Hi Luis,
I have configured Cisco 3750G switch for my CloudStack advanced mode setup.
Configuration should be the similar for Cisco 3560 as well, probably might help
you.
>> 4 Nics: 2 for Management-Storage (LACP) and 2 for Public-Guest
Make sure to setup the VLANs before configuring the switch ports for interfaces
meant for Public and Guest traffic
conf t
vlan <PUBLIC_VLAN_RANGE>,<ZONE_VLAN_RANGE>
end
Please note that the VLAN range meant for public traffic are routable (with
subnet assigned)
Configure the switch ports for Public and Guest traffic
switchport mode trunk
switchport trunk encapsulation dot1q
switchport trunk allowed vlan <PUBLIC_VLAN_RANGE>,<ZONE_VLAN_RANGE>
Ex: If 100 is VLAN ID of routable VLAN meant for public traffic, and VLAN IDs
500 to 600 are guest (zone) VLANs, then above command looks like,
switchport trunk allowed vlan 100,500-600
Regards,
Sateesh Chodapuneedi,
CloudStack Development,
Engineering, http://accelerite.com
Santa Clara, 95054, CA
@accelerite
-----Original Message-----
From: Luis <[email protected]>
Reply-To: "[email protected]" <[email protected]>, Luis
<[email protected]>
Date: Friday, 8 September 2017 at 5:39 PM
To: Paul Angus <[email protected]>, "[email protected]"
<[email protected]>
Subject: Re: Configuring CS with Advance Networking for an internal laboratory
Thank you Paul
Your article is really helpful, I think my problem is finding the correct
commands to setup the switch, this is what I have
CS 4.10: on Ubuntu 14.044 nics: 2 for management (LACP) and 2 for Storage
(LACP)
XenServer for host4 Nics: 2 for Management-Storage (LACP) and 2 for
Public-Guest
Is it possible for you or the group to help me with the lines to set up
correctly the Cisco Switch, I will appreciate your help
Cisco Switch 3560Ports: 9 - 10 for Management-storageconf tinterface range
Gi0/9 - 10switchport mode accessno shutchannel-group 3 mode
activechannel-protocol lacpend
Port 11 - 12 for Piblic-Guest
conf tinterface range Gi0/11 - 12switchport mode accessno shutchannel-group
4 mode activechannel-protocol lacpend From: Paul Angus
<[email protected]>
To: "[email protected]" <[email protected]>; Luis
<[email protected]>
Sent: Friday, September 8, 2017 5:19 AM
Subject: RE: Configuring CS with Advance Networking for an internal
laboratory
Luis,
You may find this blog from yester-year helpful:
http://www.shapeblue.com/understanding-cloudstacks-physical-networking-architecture/
Kind regards,
Paul Angus
[email protected]
www.shapeblue.com
53 Chandos Place, Covent Garden, London WC2N 4HSUK
@shapeblue
-----Original Message-----
From: Paul Angus [mailto:[email protected]]
Sent: 07 September 2017 22:12
To: Luis <[email protected]>; [email protected]
Subject: RE: Configuring CS with Advance Networking for an internal
laboratory
No problem Luis,
1. Advanced networking replies on VLANs (or some SDN isolation method),
so you need at have a range of VLANs free, that you tell CloudStack that it can
use.
2. The IP ranges I described were only an example you can you any range
you like, but ‘public’ traffic generally is going to require a gateway in order
to ‘go’ somewhere.
3. I looks to me like you are setting all of your interfaces as access
ports. You’ll need ports which deal with multiple VLANs (like ones used for
guest networks) to be trunk ports – with the VLANs which are allowed matching
those that you have told CloudStack that it can use.
Kind regards,
Paul Angus
[email protected]
www.shapeblue.com
53 Chandos Place, Covent Garden, London WC2N 4HSUK @shapeblue
From: Luis [mailto:[email protected]]
Sent: 07 September 2017 20:32
To: Paul Angus <[email protected]>; [email protected]
Subject: Re: Configuring CS with Advance Networking for an internal
laboratory
thank you for your help, I have some questions if you can help me to answer
this
1.- can i not use VLAN's for Advance Networking or are necessary for the
configuration
2.- Do I need to create an extra server ans use it as gateway for this
range of IP's?
3.- this is what I am using to create my vlan's on a Cisco 3560, is this
correct?
conf t
interface range Gi0/9 - 10
switchport mode access
no shut
switchport access vlan 65
channel-group 3 mode active
channel-protocol lacp
end
Thank you for your help
________________________________
From: Paul Angus <[email protected]<mailto:[email protected]>>
To: "[email protected]<mailto:[email protected]>"
<[email protected]<mailto:[email protected]>>; Luis
<[email protected]<mailto:[email protected]>>
Sent: Thursday, September 7, 2017 3:05 PM
Subject: RE: Configuring CS with Advance Networking for an internal
laboratory
Hi Luis,
You can give CloudStack a range of RFC1918 addresses (ie private addresses)
to act as an 'internal' public network.
10.0.1.10 - 10.0.1.30
GW: 10.0.1.254
Netmask - 255.255.255.0
If the gateway at 10.0.1.254 can route to the outside world then CloudStack
will still be able to download templates, if not you can always register a
template which you are hosting on an internal network.
If you do the second option ensure that the global setting
'secstorage.allowed.internal.sites' includes the hosting server's IP address.
Kind regards,
Paul Angus
[email protected]<mailto:[email protected]>
www.shapeblue.com<http://www.shapeblue.com>
53 Chandos Place, Covent Garden, London WC2N 4HSUK @shapeblue
-----Original Message-----
From: Luis
[mailto:[email protected]<mailto:[email protected]>]
Sent: 07 September 2017 18:42
To: Users <[email protected]<mailto:[email protected]>>
Subject: Configuring CS with Advance Networking for an internal laboratory
Hi
I am configuring CS with Advance Networking for internal use without
rotatable IP's, this is for testing and lean CS Advance Networking, This is
what I have CS 4.10XenServer 7.0FreeNas CS is already installed but I can't
download any iso because V-Router can't ping outside my network, any advice?
Public IP:209.229.131.0Internal IP: 10.0.0.0 Thank you for your help.
DISCLAIMER
==========
This e-mail may contain privileged and confidential information which is the
property of Accelerite, a Persistent Systems business. It is intended only for
the use of the individual or entity to which it is addressed. If you are not
the intended recipient, you are not authorized to read, retain, copy, print,
distribute or use this message. If you have received this communication in
error, please notify the sender and delete all copies of this message.
Accelerite, a Persistent Systems business does not accept any liability for
virus infected mails.
