On Wednesday 02 November 2005 23:41, Tassilo Horn wrote: > Blaisorblade wrote: > > It's a FAQ, your /etc/inittab uses DevFS names, while it should be > > updated to normal ones. I.e. vc/0 or ttys/0 rather than tty0, and so > > on. At least, this is the normal thing. > Does this apply to udev-enabled systems (host and guest), too? Sorry, I said the reverse of what I actually meant.
You can find in inittab vc/0 or ttys/0, which are wrong, and you must go back to tty0. tty1 is correct with udev and/or static dev... Revert back the change. In this case, you have a problem with channel selection - either in the config there's none enabled, or the ones which are enabled don't work for some reason (for instance, you're using the "xterm" default but you don't have xterm installed or X running or DISPLAY set in the env). > After I've changed my inittab from > # TERMINALS > c1:12345:respawn:/sbin/agetty 38400 tty1 linux > [EMAIL PROTECTED]> linux ubd0=root_fs > Checking for /proc/mm...found > Checking for the skas3 patch in the host...found > Checking PROT_EXEC mmap in /tmp...OK > Linux version 2.6.12-usermode-r2-bs11 ([EMAIL PROTECTED]) (gcc-Version 4.0.2 > (Gentoo 4.0.2-r1, HTB-4.0.1-1.00, pie-8.7.8)) #4 Wed Nov 2 20:00:37 CET > 2005 > Built 1 zonelists > Kernel command line: ubd0=root_fs root=98:0 > PID hash table entries: 256 (order: 8, 4096 bytes) > Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) > Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) > Memory: 28720k available > Mount-cache hash table entries: 512 > Checking for host processor cmov support...Yes > Checking for host processor xmm support...No > Checking that ptrace can change system call numbers...OK > Checking syscall emulation patch for ptrace...OK > Checking advanced syscall emulation patch for ptrace...OK > Checking that host ptys support output SIGIO...Yes > Checking that host ptys support SIGIO on close...No, enabling workaround > Checking for /dev/anon on the host...Not available (open failed with > errno 2) > NET: Registered protocol family 16 > mconsole (version 2) initialized on /root/.uml/omwtSk/mconsole > Initializing Cryptographic API > io scheduler noop registered > io scheduler cfq registered > NET: Registered protocol family 2 > IP: routing cache hash table of 512 buckets, 4Kbytes > TCP established hash table entries: 2048 (order: 2, 16384 bytes) > TCP bind hash table entries: 2048 (order: 1, 8192 bytes) > TCP: Hash tables configured (established 2048 bind 2048) > NET: Registered protocol family 1 > Initialized stdio console driver > Console initialized on /dev/tty0 > ubda: unknown partition table > VFS: Mounted root (ext2 filesystem) readonly. > line_ioctl: tty0: ioctl KDSIGACCEPT called > INIT: version 2.86 booting > line_ioctl: tty0: ioctl TIOCLINUX called > > Gentoo Linux; http://www.gentoo.org/ > Copyright 1999-2005 Gentoo Foundation; Distributed under the GPLv2 > > Press I to enter interactive boot mode > > * Mounting proc at /proc ... [ ok ] > * Mounting sysfs at /sys ... [ ok ] > * Mounting /dev for udev ... [ ok ] > * Configuring system to use udev ... > * Setting /sbin/udevsend as hotplug agent ... [ ok ] > * Mounting devpts at /dev/pts ... [ ok ] > * Activating (possible) swap ... [ ok ] > * Skipping root filesystem check (fstab's passno == 0) ...[ ok ] > * Remounting root filesystem read/write ... [ ok ] > * Setting hostname to uml ... [ ok ] > * System.map not found - unable to check symbols > * Checking all filesystems ... [ ok ] > * Mounting local filesystems ...mount: special device /dev/ubd/1 does > not exist > * Some local filesystem failed to mount [ !! ] > * Activating (possibly) more swap ... [ ok ] > * Setting system clock using the hardware clock [UML] ... [ ok ] > * Configuring kernel parameters ... [ ok ] > * Updating environment ... [ ok ] > * Cleaning /var/lib/net-scripts/state ... [ ok ] > * Cleaning /var/lock, /var/run ... [ ok ] > * Cleaning /tmp directory ... [ ok ] > * Starting lo > * Bringing up lo > * 127.0.0.1/8 [ ok ] > * Adding routes > * 127.0.0.0/8 ... [ ok ] > * Initializing random number generator ... [ ok ] > INIT: Entering runlevel: 3 > * Starting local ... [ ok ] > * umlboot starts network interfaces config ... > * Unable to locate /opt/umlboot script ! > * Starting sshd ... > > That's it. > > Regards, > Tassilo -- Inform me of my mistakes, so I can keep imitating Homer Simpson's "Doh!". Paolo Giarrusso, aka Blaisorblade (Skype ID "PaoloGiarrusso", ICQ 215621894) http://www.user-mode-linux.org/~blaisorblade ___________________________________ Yahoo! Mail: gratis 1GB per i messaggi e allegati da 10MB http://mail.yahoo.it ------------------------------------------------------- SF.Net email is sponsored by: Tame your development challenges with Apache's Geronimo App Server. Download it for free - -and be entered to win a 42" plasma tv or your very own Sony(tm)PSP. Click here to play: http://sourceforge.net/geronimo.php _______________________________________________ User-mode-linux-user mailing list User-mode-linux-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/user-mode-linux-user
